ENGLAON LED24X80 24 Inch Full HD Smart 12V TV User Manual
- June 15, 2024
- ENGLAON
Table of Contents
LED24X80 24 Inch Full HD Smart 12V TV
Product Information
Model: LED24X80
This is a 24-inch Full HD LED TV DVD Combo. It features a
built-in DVD player for convenient playback of DVDs. The TV has
various input terminals for connecting external equipment,
including one AUDIO L/R output, one EARPHONE output, one RF input,
two HDMI inputs, two USB inputs, one COAXIAL output, and one RJ45
input.
Safety Information
Important Safety Precautions:
-
Please, immediately pull out the AC power plug from the adapter
if there is an abnormal sound or smell or if the LED TV has sound
but no picture, and contact after sales support. -
The LED TV should be kept free from rain, moisture, and dust to
prevent electrical shock and short circuits. Do not cover the
ventilation openings with tablecloths, curtains, newspapers,
etc. -
The LED TV should be kept away from high-temperature heating
sources or direct sunlight. Good ventilation is required. Allow 10
cm of space between the LED TV and other appliances or built-in
cabinet walls. -
When cleaning the front cabinet, please make sure the power
plug is pulled out and use a soft, dry, lint-free cloth. Do not
repeatedly wipe the panel or scrape, tap, or strike it with a hard
object. -
Do not use any petrol, chemical, or alcohol-based solvents to
clean the LED TV as it may damage the panel and cabinet. -
When the television receiver is not used for an extended period
of time, it is advisable to disconnect the AC power cord from the
AC outlet. -
Do not place the LED TV on an unstable surface.
-
Do not place the power cord or other cables across a walkway in
case they are trampled on. Do not overload the power cord or power
socket. When disconnecting and connecting the device using the
power plug, it should easily go into the power source. -
Do not disassemble the back cover, as it contains high voltages
inside and may cause electric shock. Only qualified professionals
should conduct internal adjustments, maintenance, and checks. -
The TV set should not be subjected to water droplets, vapor, or
splash. This equipment should not be placed on objects filled with
liquids. Do not place flame sources, such as lit candles, on or
near the LED TV. If there are abnormal objects or water in the TV,
please pull out the power plug and contact after-sales
support. -
Pull out the power cord and antenna cable during electrical
storms to prevent damage to the LED TV from electrical surges. Keep
all people away from the antenna cable during electrical
storms.
Product Usage Instructions
To use the LED TV DVD Combo:
-
Assemble the stand according to the instructions provided in
the user manual. -
Connect the antenna cable to the RF input for receiving TV
signals. -
Connect external equipment, such as a DVD player or set-top
box, via HDMI inputs for audio and video playback. -
If you want to connect earphones for private listening, use the
EARPHONE output. -
Make sure the LED TV is connected to a power source using the
AC power cord. -
Turn on the LED TV by pressing the power button on the remote
control. -
To navigate through the on-screen display (OSD) menu, use the
buttons on the remote control. -
If you encounter any issues with the DVD player, refer to the
DVD troubleshooting section in the user manual for possible
solutions. -
If you experience picture defects, refer to the section on
picture defects and their reasons in the user manual for
troubleshooting steps.
USER’S MANUAL
24″ FHD LED TV DVD COMBO
Model: LED24X80
User’s Manual
Please Read this manual carefully and retain for future reference
Scan to download the Manual
For support please contact our service department at service@englaon.com.au
Safety Information
IMPORTANT SAFETY INSTRUCTIONS
Read these instructions. Keep these instructions. Heed all warnings. Follow
all instructions. Do not use this apparatus near water. Clean only with dry
cloth. Do not block any ventilation openings. Install in accordance with the
manufacture’s instructions. Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus (including amplifiers)
that produce heat. Do not defeat the safety purpose of the polarized or
grounding plug. A polarized plug has two blades with one wider than the other.
A grounding plug has two blades and a third grounding prong. The wide blade or
the third prong is provided for your safety. If the provided plug does not fit
into your outlet, consult an electrician for replacement of the obsolete
outlet. Protect the power cord from being walked on or pinched particularly at
the plugs, convenience receptacles, and at the point where they exit from the
apparatus. Only use attachments/accessories specified by the manufacturer. Use
only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart or rack is used, use
caution when moving the cart/apparatus combination to avoid injury from tip-
over.
Unplug the apparatus during lightning storms or when unused for long periods
of time. Refer all servicing to qualified personnel. Servicing is required
when the apparatus has been damaged in any way, such as power supply cord or
plug is damaged, liquid has been spilled or objects have fallen into the
apparatus has been exposed to rain or moisture, does not operate normally, or
has been dropped. CAUTION: These servicing instructions are for use by
qualified service personnel only. To reduce the risk of electric shock, do not
perform any servicing other than that contained in the operating instructions
unless you are qualified to do so. WARNINGTo reduce the risk of fire or
electric shock, do not expose this apparatus to rain or moisture. The
apparatus shall not be exposed to dripping or splashing and that objects
filled with liquids, such as vases, shall not be placed on apparatus. WARNING:
The mains plug is used as disconnect device, the disconnect device shall
remain readily operable.
– This lightning flash with arrowhead symbol within an equilateral triangle is
intended to alert the user to the presence of non-insulated “dangerous
voltage” within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock. – Warning: To reduce the risk of electric
shock, do not remove cover (or back) as there are no user-serviceable parts
inside. Refer servicing to qualified personnel. – The exclamation point within
an equilateral triangle is intended to alert the user to the presence of
important operating and maintenance instructions in the literature
accompanying the appliance. Apparatus with class I construction shall be
connected to a mains socket outlet with a protective earthing connection.
Important Safety Precautions
Please, immediately pull out the AC power plug from adapter if there is an
abnormal sound or smell or the LED TV has sound but no picture, and contact
after sales support.
The LED TV should be kept free from rain, moisture and dust to prevent
electrical shock and short circuits. Do not cover the ventilation openings
with table clothes, curtains, newspapers, etc.
The LED TV should be kept from high temperature heating sources or direct
sunlight. Good ventilation is required. Allow 10 cm. between the LED TV and
other appliances or built-in cabinet walls.
When you wipe the front cabinet, please make sure the power plug is pulled out
and use a soft, dry, lint-free cloth and handle it with care. Do not
repeatedly wipe the panel, nor scrape, tap or strike the panel with a hard
object.
Do not wipe the LED TV with any petrol, chemical or alcohol based solvents as
it will lead to product damage of the panel and cabinet.
When the television receiver is not used for an extended period of time, it is
advisable to disconnect the AC power cord from the AC outlet.
Important Safety Precautions
Do not place the LED TV on an unstable surface.
Do not place the power cord or other cables across a walkway in case it is
trampled on. Do not overload the power cord or power socket. When the power
plug is used to disconnect and connect the device, it should easily go into
the power source.
Do not disassemble the back cover, as it contains high voltages inside and
will cause electric shock. Only qualified professionals should conduct
internal adjustments, maintenance, and checks.
The TV set should not be subjected to water droplets, vapor, or splash. This
equipment should not be placed on objects filled with liquids. Do not place
flame sources, such as lit candles, on or near the LED TV. Please, pull out
the power plug and contact after sales support if there are abnormal objects
or water in the TV.
Pull out the power cord and antenna cable during electrical storms so the LED
TV is not damaged by electrical surges. Keep all people away from the antenna
cable during electrical storms.
Table of Contents
Introduction Features Accessories Specifications Hardware Configuration
General Description Overview of front and side panel Overview of back panel
Assembling Stand Process Overview of remote control Installing Batteries in
the Remote Control
Antenna connection
External Connection Connecting DVD Player/Set-Top Box via HDMI Connecting
EARPHONE
Supporting signals
Basic operation Turning the TV On and Off
OSD Menu Operations
DVD Troubleshooting
Picture defects and the reason
2 2 3 3
4 4 5 6-8 6-8 9
10-11 10 11
11
12 12
13-31
32-33 34 35
1
Introduction
Features
Input terminals used for external equipment connection
One AUDIO L/R output One EARPHONE output One RF input
Two HDMI input Two USB input One COAXIAL output One RJ45 input
Batteries (AAAx 2)
Instructions Manual
Remote Control Column bracket
Base
Screws
2
Introduction WSpaercniifincgastions
Model Power supply
Video input Format Antenna input Average Power Consumption
Color LED display LED24X80 1920X1080 DC 12V 4A PAL/DVB-T
48.25MHz-863.25MHz PAL/NTSC
antenna socket 75 32W
541.4 x 125 x 345.7 mm
3.7 Kg
0oC-35oC
Remarks: The above listed specifications and data are subject to change without prior notice.
Hardware Configuration
CPU GPU DDR SIZE eMMC Flash
ARM Cortex-A55 quad core Mali G31MP2 1.5 GB 8 GB
3
POWER
CH+
SOURCE
VOL+ MENU VOL-
CH-
SPEAKER REMOTE CONTROL SENSOR
POWER INDICATOR White: standby mode. Transparent: power on mode.
SOURCE Toggles between all the available input sources MENU Press to see an
on-screen menu of your TV’s features. CH+/Press to change channels. In the on-
screen menu, use the CH +/buttons as up/down arrow buttons.
VOL+/Press to increase or decrease the volume. In the on-screen menu, use the
VOL +/buttons as left/right arrow buttons.
POWER Press POWER button to toggle between normal and standby mode.
100 mm
Screw M4 x 8MM
100 mm
4
Side port
DC 12V
RJ45
COAXIAL OUT
L
R HDMI2
HDMI1 RF
1 Port
USB2
2
3
EARPHONE OUT
USB1
4
5
67
8
9
10
1. DC 12V
6. HDMI1
DC input.
Connecting for HDMI signal.
2. RJ45
7. RF
Ethernet connection.
Connected to external antenna to receive
3. COAXIAL
the ATV/DTV program in ATV/DTV mode.
Coaxial Digital audio output.
8. USB 2
4. L/R
USB input.
Connect to the audio output jacks on your 9. EARPHONE
amplifier/home theater.
Connecting for headphone.
5. HDMI2
10.USB 1
Connecting for HDMI signal.
USB input.
Assembling Stand Process
Screw hole A Screw hole B
Screw
Screw hole C
Screw
Screw hole D
Instruction: 1.Place the TV unit on a flat and clean table. 2.Fix stand by 2 pcs screws via screw hole B and A. 3.Fix stand by 3 pcs screws via screw hole D and C.
General Description
Overview of remote control
1
2
3
4
5
7
6
8
9
11
10
12
13
15
14
16
18
19 17
20
21
23
22
24
General Description
Overview of remote control
1. POWER: Turn the TV on and off. 2. : Search function. 3. Digital
Buttons(0-9, -): Directly select channel with digital buttons. 4. SOURCE:
Press to open the input source list. 5. NETFLIX: If network connects, press
this key to view NETFLIX directly. 6. Google Play: If network connects, press
this key to view Google Play directly. 7. YouTube: If network connects, press
this key to view YouTube directly. 8. Prime Video: If network connects, press
this key to view Prime Video directly. 9. HOME: Display the HOME page. 10.
Arrow button : Use to select on-screen menu items and change menu values. 11.
MENU: Display the main menu or exit the current menu. 12. OK: Confirms
selection. 13. BACK: Return to the previous menu. 14. MUTE: Press this button
to cut off the sound of the TV set temporarily, press again to resume. 15.
EXIT: Exit the menu. 16. VOL +/- : Press these buttons to adjust the volume.
17. COLOR BUTTONS: It’s used in the APPS.
: Open/close in DVD mode. D.MENU: Quick navigation during Teletext or setup
settings / DVD: Video DVD Menu button. SETUP: DVD system setup. D.DISP: Quick
navigation during Teletext or setup settings / DVD: DVD Information button.
7
General Description
Overview of remote control
18. CH/: Press these buttons to change channel upward or downward. 19. GUIDE:
Select electronic program guide, in DTV mode, it will display all the
information of program in a week when pressing this button. 20. DIGITAL MEDIA
PLAYER CONTROL BUTTON: Include backward, forward, play/pause, stop in USB
mode. In DTV mode, press button to record the TV program. Please refer to
relevant instructions in the section of multimedia player. 21. LIST: Press to
display the channel list. A-B: Press the A-B button once to set point A. Press
the A-B button a second time to set point B. After setting the program repeat
playing from A to B. Pressing the AB button a third time will cancel the
repeat. 22. TEXT: Press to select the teletext mode. REPEAT: DVD: Repetition
mode button. 23. AUDIO: Press to select mono, nicam, stereo for ATV channel,
audio language for DTV channel. 24. SUBT: Open or close subtitle. TITLE: Press
this button to return to the title of the disc.
8
General Description
Installing Batteries in the Remote Control
Installing Batteries
1 Open the battery compartment cover on the back side.
Battery Cover
Insert two 1.5V AAA size batteries in
2 correct polarity. Don´t mix old or used batteries with new ones.
2xsize AAA 1.5V
Point the remote towards the remote control sensor of the wireless TV and use
it within 7 meters.
Put the used batteries into the recycling bin since it can negatively affect
the environment.
3 Closed the cover.
Battery Cover
The battery (battery or batteries or battery pack) shall not be exposed to excessive heat such as sunshine, fire or the like.
External Connection
Antenna connection
Antenna input impedance of this unit is 75ohm. VHF/UHF 75ohm coaxial cable can be
connected to the antenna jack directly, if the antenna cable is 300ohm parallel flat feeder
cable, you need to use the 300ohm/75ohm converter to connect the antenna cable to the
antenna jack. For details Please refer to the following drawing.
Antennas with 300ohm flat twins Leads
Antennas with 75ohm Round Leads
Use a 75ohm – 300ohm converter ANT IN
300ohm coaxial cable Antenna feeder
9
75ohm coaxial cable
Antenna cable
External Connection
Connecting DVD Player/Set-Top Box via HDMI
This connection can only be made if there is a HDMI Output connector on the external device.
DVD Player/Set-Top Box
TV Rear Panel
IN HDMI
HDMI Cable (Not supplied)
What is HDMI? HDMI, or high-definition multimedia interface, is a next-
generation interface that enables the transmission of digital audio and video
signals using a single cable without compression. Multimedia interface is a
more accurate name for it especially because it allows multiple channels of
digital audio (5.1 channels). The difference between HDMI and DVI is that the
HDMI device is smaller in size, has the HDCP(High Bandwidth Digital Copy
Protection) coding feature installed, and supports multi-channel digital
audio. Each DVD player/STB has a different back panel configuration. We
recommend the use of cables with a Ferrite Core.
1. Connect an HDMI Cable between the HDMI connector on the TV and the HDMI
connector on the DVD player/Set-Top Box.
10
External Connection
Connecting EARPHONE
EARPHONE OUT
Phone Out
1.Plug EARPHONE out connector into EARPHONE out jack on the TV the TV speaker
will be muted.
Supporting signals
Basic Operation
Turning the TV On and Off
How to turn the TV on or off 1. Insert the power cord plug into a polarized DC
outlet.
2. Press POWER button on the remote control or button on the LED TV.
3. Normal picture will be displayed on the screen after 6 seconds. If no
signal input, “No Signal” will be displayed on the screen.
4. If temporary POWER off is required, press POWER button on the remote
control or button on the LED TV.
5. Press and hold the power button for 6 seconds to completely turn off this
device, after which you may choose to power it off or restart the TV, or you
can unhook the unit’s power cord plug.
6. After switching off the device, you should turn on the TV again at least 5
seconds later.
Status indication lamp Green: In power on mode. Red: In standby mode.
Auto power-off If there is no signal input in any Mode, the TV will
automatically accesses the standby state in about 15 minutes.
Memory before turning TV off The settings of picture and the preset channels
will be memorized at turning off the unit. When being started up again, the
unit will work according to the mode set before being turned off.
11
12
OSD Menu Operations
INITIAL SETUP This function is used for the remote control pair code. After
the code is successful, you can use the Bluetooth remote control to operate
the TV.
OSD Menu Operations
Connect your Android phone to your TV, select “Continue” to continue the
connection, and choose “Skip” to skip this step.
Press / to select the system language and press OK to confirm the language.
Press / to select the wifi to connect, press OK and enter the password to confirm the connection is successful.
By agreeing to automatically send diagnostic information to Google to improve discriminative power, choose “YES” to accept.
13
14
OSD Menu Operations
OSD Menu Operations
HOME SCREEN After completing the wizard Settings, you can watch TV and go to
the home screen.
1
2
1. Your device is powered by Android TV and press the button to select the browsing feature. 2. You can get more apps from Google Play and press the button to go to the next screen. 3. Transfer photos and other content to the TV via the built-in chromecast, press OK to complete the browsing.
1. Open Google Assistant or start a text search. 2. Among the applications
installed on the TV, the icons for the favourite applications are shown inside
here. (Favourite applications can be added/ deleted/changed its order by
users.)
Inputs: Icon to select an input source. Settings: Various settings can be
configured here. For details on the settings, see the next explanation.
INPUT SOURCE In the HOME interface, press /// to select the “Inputs” icon,
press OK to open the input source list, then press up to highlight an input
and press OK to switch.
Press / to select the country of your deviceand press OK to confirm.
15
16
OSD Menu Operations
Under live TV, press the SOURCE button to display the list of input sources.
You can select the desired source.
OSD Menu Operations
Network 1 Press / button to select what you want set. 2. press OK button to
adjust. 3. After finishing your adjustment, press OK button to save and return
to the previous menu.
NAVIGATING THE ON-SCREEN MENU 1. In the HOME interface, press the key to select the icon of the circular settings menu, press OK to confirm.
APPS
2. Press / button to select what you want set. 3. Press OK to enter setting.
17
In this menu, you can set the APP permissions, and read the app lists. 1.
Press / button to select what you want set. 2. Press OK button to adjust. 3.
After finishing your adjustment, press BACK button to return to the previous
menu.
18
OSD Menu Operations
DEVICE PREFERENCES ABOUT
OSD Menu Operations
DATE & TIME
In this menu, you can read the information and settings of TV. 1. Press / button to select what you want set. 2. Press OK button to adjust. 3. After finishing your adjustment, press BACK button to return to the previous menu.
Automatic date & time- Press / button to select the option then press OK
button to enter the sub-menu.(Optional: Use network-provided time, Off)
Manually adjusting date & time settings will automaticall change the Automatic
date & time to OFF.
Set date- Press / button to select the option then press OK button to enter
the sub-menu. Set time- Press / button to select the option then press OK
button to enter the sub-menu. Set time zone- Press / button to select the
option then press OK button to enter the submenu. Use 24-hour format-Press /
button to select the option then press OK button to choose ON/OFF.
19
20
OSD Menu Operations
LANGUAGE
OSD Menu Operations
STORAGE
Language- Press / button to select the optionthen press button to enter the OK
select language. KEYBOARD
Current keyboard- Press / button to select the option then press OK button to
enter the sub-menu. Gboard Settings- Press / button to select the option then
press OK button to enter the sub-menu. Manage keyboards- Press / button to
select the option then press OK button to enter the sub-menu.
21
Internal shared storage- Press / button to select the option then press OK
button to enter the sub-menu. Removable Storage- Press / button to select the
option then press OK button to enter the sub-menu.(Note: Show external devices
if available) HOME SCREEN
In this menu, you can set channels, apps, open source licenses. 1. Press /
button to select what you want set. 2. Press OK button to adjust. 3. After
finishing your adjustment, press BACK button return to the previous menu.
22
English
OSD Menu Operations
GOOGLE
OSD Menu Operations
SCREEN SAVER
In this menu, you can set searchable apps, safe search filter, block offensive
words, open source licenses. 1. Press / button to select what you want set. 2.
Press OK button to adjust. 3. After finishiing your adjustment, press BACK
button return to the previous menu.
CHROMECAST BUILT-IN
Screen saver- Press / button to select the option then press OK button to
enter the sub-menu.(Optional: Turn screen off, Backdrop, Colors) When to
Start- Press / button to select the option then press OK button to enter the
sub-menu. (Optional: 5 minutes, 15 minutes, 30 minutes, 1 hour, 2 hours.)
Start now- Press / button to select the option then press OK button to enter
screen saver.
ENERGY SAVER
In this menu, you can read the information and settings of Chromecast. 1.
Press / button to select what you want set. 2. Press OK button to adjust. 3.
After finishing your adjustment, press BACK button return to the previous
menu.
23
Turn off Display- Press / button to select the option then press OK button to
enter the sub-menu. (Options: 15 minutes, 30 minutes, ….24 hours, Never.)
24
Media Menu Operations
L O C AT I O N
OSD Menu Operations
ACCESSIBILITY
Location status- Press / button to select the option then press OK button to
enter the sub-menu. (Optional: Use Wi-Fi to estimate location, Off) USAGE &
DIAGNOSTICS
Usage & diagnostics- Press / button to select the option then press button OK
to choose ON/OFF.
Captions- Press / button to select the option then press OK button to enter the submenu. High contrast text- Press / button to select the option then press OK button to choose ON/OFF. Text to speech- Press / button to select the option then press OK button to enter the sub-menu. Accessibility shortcut- Press / button to select the option then press OK button to choose ON/OFF. TalkBack- Press / button to select the option then press OK button to enter the submenu. Switch Access- Press / button to select the option then press OK button to enter the sub-menu.
25
26
OSD Menu Operations
R E S TA R T Press OK button to enter the sub-menu. Restart the TV.
27
OSD Menu Operations
ADD AND USE OF MEDIA PLAYER
1. In the HOME interface, select the + icon in the APP column to add the
application, and click OK. Press up and down to select the Media Player
application, and click to add it OK to the HOME interface.
2. Focus on the corresponding USB driver and press OK to display video,
photo, audio files. Press navigation button to select the file.
28
OSD Menu Operations
PICTURE
OSD Menu Operations
SOUND
Picture Mode- Press / button to select the option button to enter the
submenu.(Optional: Standard, Dynamic, Movie, Eye Comfort, Gentle, Vivid,
Sport, Personal). Brightness/Color Saturation/Hue/Contrast/Gamma/Black Level
SharpnessPress / button to select the option. Press to decrease the parameter.
Press to increase the parameter. Gamma- Press / button to select the option.
Press to decrease the parameter. Press to increase the parameter.
ECO Press MENU key to the main menu, and select Picture. Press button to ECO
option and press OK to select the option.
Press MENU key to the main menu, and select Sound. Sound Mode- Press OK to
enter the sub-menu, press button to select option and press OK to select the
option. Pure Sound- Press / button to select the option then press OK button
to choose ON/OFF. Surround- Press / button to select the option then press OK
button to choose O N / O F F. Sound Only- Press OK to enter the sub-menu,
press OK button to select option. Output Device- Press / to enter the sub-
menu. Audio Output Type- Press / to enter the sub-menu. Advanced Settings-
Press / to enter the sub-menu.
SYSTEM
Press MENU key to the main menu, and select System. Press / button to select option and press OK to select the option.
29
30
OSD Menu Operations Media
Media Player
Movie on Media Player menu, move cursor to moive, press [OK] button to enter
into FileSelector menu. Select the file you want to play, press [PLAY/PAUSE]
to enter into full screen play. Press [LEFT]/[RIGHT] button to move cursor,
and operate according to different hint.
Music In the same way, on Media Player menu, move cursor to Music, press [OK]
button to enter into FileSelector menu. Select the file you want to play,
press [PLAY/PAUSE] to enter into full screen play. Press [LEFT]/[RIGHT] button
to move cursor, and operate according to different hint.
Photo In the same way, on Media Player menu, move cursor to Photo, press [OK]
button to enter into FileSelector menu. Select the file you want to play,
press [PLAY/PAUSE] to enter into full screen play. Press [LEFT]/[RIGHT] button
to move cursor, and operate according to different hint.
31
DVD
SOURCE Press the “SOURCE” button menu, through the up and down direction keys
can be select, Press the left or right button to select the DVD, and press the
Enter button to enter. Press the DVD SETUP button to enter.
TV SYSTEM Set the options are: NTSC/PAL/AUTO. POWER RESUME Press the ENTER
function on or off with. TV TYPE Set the screen ratio options are: PS(4:3 Pan
Scan), Normal/PS(4:3 Letter Box), and Wide (16:9)the default settings is wide.
PA S S W O R D Enter “0000” to enter. R AT I N G Level Disc Options. D E FA U
LT This option will return the DVD to it’s factory default settings.
32
DVD
OSD LANGUAGE Set the OSD Language options. AUDIO LANG DVD language selection
options. SUBTITLE LANG This player can display DVD subtitle languages if
supported by the DVD disc. when playing DVD’s you can hide the subtitle or
choose any of them as the current subtitle language. MENU LANG Set the MENU
Language options.
AUDIO OUT Press the “ENTER” Key enter, through the up and down direction keys
can be select. KEY Press the “ENTER” Key enter, through the up and down
direction keys can be select.
DUAL MONO Press the “ENTER” Key enter, through the up and down direction keys
can be select. 33
Troubleshooting
Disconnect the power cord, wait 60 seconds then reconnect the power cord and
restart the TV. C
Increase the volume. please check sound settings.
C No support for this function.
E E
E E
34
Picture defects and the reason
35
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>