CRYSTAL IMAGE TECHNOLOGIES RMD-151-19A-MIL Military Grade Pack Mount Industrial Display Drawer User Manual

CRYSTAL IMAGE TECHNOLOGIES RMD-151-19A-MIL Military Grade Pack Mount

Industrial Display Drawer

Product Information

Product Name: Military Grade Rack Mount

Industrial Display Drawer Options:

• Composite Video input
• HDMI / Display port input
• Touchscreen / DC power
• 3G / HD / SD-SDI broadcasting grade input
• EMC or AR Hardness glass

Safety Instructions

1. Unplug equipment before cleaning. Use a moist cloth, not liquid or spray detergent.
2. Keep the equipment away from excessive humidity and heat. Preferably, keep it in an air-conditioned environment.
3. Place the equipment on a sturdy, level surface during installation to prevent accidental falling and damage.
4. Do not cover, block, or obstruct the gap between the equipment and the power supply when it is in an open position to ensure proper air convection and prevent overheating.
5. Arrange the power cord in a way that avoids tripping hazards. Use a power cord rated for the voltage and current labeled on the equipment.
6. Observe all precautions and warnings attached to the equipment.
7. Disconnect the equipment from the power outlet if not in use for an extended period to prevent damage from transient over-voltage.
8. Keep liquids away from the equipment to avoid spillage and potential damage, fire, or electrical shock.
9. Only qualified service personnel should open the chassis to avoid damaging the equipment and voiding the warranty.
10. If any part of the equipment becomes damaged or stops functioning, have it checked by qualified service personnel.

Warranty Coverage Exclusions

• Products with defaced, modified, or removed serial numbers.
• Removal, installation, and set-up service charges.

Regulatory Notices (Federal Communications Commission – FCC):

• Re-position or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a different circuit from that of the receiver.

Product Usage Instructions

Before Installation:

1. Mount the equipment in a suitable cabinet or on a stable surface.
2. Ensure the installation location has good ventilation, is out of direct sunlight, and away from sources of excessive heat.

Contents:

• Package Content
• Structure Diagram & Dimension
• Installation Specifications / OSD
• Product Specifications
• On-screen Display Operation (OSD) Options
• Touchscreen: Resistive, Capacitive
• DC power

Military Grade Rack Mount Industrial Display Drawer

Part# RMD-151-19A-MIL
Options :

• Composite Video input
• HDMI / Display port input
• Touchscreen / DC power
• 3G / HD / SD-SDI broadcasting grade input
• EMC or AR Hardness glass

Legal Information

Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. The information in this document is subject to change without notice. We are not liable for any injury or loss that results from the use of this equipment.

Safety Instructions

Please read all of these instructions carefully before you use the device. Save this manual for future reference.

• Unplug equipment before cleaning. Don’t use liquid or spray detergent; use a moist cloth.
• Keep equipment away from excessive humidity and heat. Preferably, keep it in an air-conditioned environment with temperatures not exceeding 40º Celsius (104º Fahrenheit).
• When installing, place the equipment on a sturdy, level surface to prevent it from accidentally falling and causing damage to other equipment or injury to persons nearby.
• When the equipment is in an open position, do not cover, block or in any way obstruct the gap between it and the power supply. Proper air convection is necessary to keep it from overheating.
• Arrange the equipment’s power cord in such a way that others won’t trip or fall over it.
• If you are using a power cord that didn’t ship with the equipment, ensure that it is rated for the voltage and current labeled on the equipment’s electrical ratings label. The voltage rating on the cord should be higher than the one listed on the equipment’s rating label.
• Observe all precautions and warnings attached to the equipment.
• If you don’t intend on using the equipment for a long time, disconnect it from the power outlet to prevent being damaged by transient over-voltage.
• Keep all liquids away from the equipment to minimize the risk of accidental spillage. Liquid spilled onto the power supply or on other hardware may cause damage, fire, or electrical shock.
• Only qualified service personnel should open the chassis. Opening it yourself could damage the equipment and invalidate its warranty.
• If any part of the equipment becomes damaged or stops functioning, have it checked by qualified service personnel.

What the warranty does not cover

• Any product, on which the serial number has been defaced, modified ed or removed.
• Damage, deterioration or malfunction resulting from:
  • Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or failure to follow instructions supplied with the product.
  • Repair or attempted repair by anyone not authorized by us.
  • Any damage of the product due to shipment.
  • Removal or installation of the product.
  • Causes external to the product, such as electric power fluctuation or failure.
  • Use of supplies or parts not meeting our specifications.
  • Normal wear and tear.
  • Any other causes which does not relate to a product defect.
• Removal, installation, and set-up service charges.

Regulatory Notices Federal Communications Commission (FCC)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Any changes or modifications made to this equipment may void the user’s authority to operate this equipment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Re-position or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

Before Installation

• It is very important to mount the equipment in a suitable cabinet or on a stable surface.
• Make sure the place has good ventilation, is out of direct sunlight, away from sources of excessive dust, dirt, heat, water, moisture and vibration.

Unpacking

The equipment comes with the standard parts shown in the package content. Check and make sure they are included and in good condition. If anything is missing, or damaged, contact the supplier immediately.

How To Clean Your LCD Monitor

Caution

• To avoid the risk of electric shock, make sure your hands are dry before unplugging your monitor from or plugging your monitor into an electrical outlet.
• When you clean your monitor, do not press down on the LCD screen. Pressing down on the screen can scratch or damage your display. Pressure damage is not covered under warranty.
• Use only cleansers made specifically for cleaning monitors and monitor screens. Cleansers not made to clean monitors and monitor screens can scratch the LCD display or strip off the fi nish.
• Do not spray any kind of liquid directly onto the screen or case of your monitor. Spraying liquids directly onto the screen or case can cause damage which is not covered under warranty.
• Do not use paper towels or abrasive pads to clean your monitor. Using an abrasive pad or any wood-based paper product such as paper towels can scratch your LCD screen.

Cleaning Your Monitor
To clean your LCD safely, please follow these steps

1. Disconnect the power cord.
2. Gently wipe the surface using a clean, dry microfiber cloth. Use as little pressure as possible.

Cleaning Tough Marks and Smudges
To remove tough marks and smudges, please follow these steps

1. Disconnect the power cord.

2. Spray a small amount of non-abrasive cleanser on a microfiber cloth.
   Caution : Do not spray or apply any liquids directly onto the monitor. Always apply the solution to your microfi ber cloth fi rst, not directly on the parts you are cleaning.

3. Gently wipe the surface. Use as little pressure as possible.

4. Wait until your monitor is completely dry before plugging it in and powering it up.

Package Content

19″ Monitor X 1

• 1.8 M VGA cable X 1
• 1.8 M DVI cable X 1
• 1.8 M Audio cable X 1
• Power cord X 1

Structure Diagram

1. 19″ LCD panel
2. Audio speakers x 2
3. LCD OSD Buttons
4. Handle
5. Thumbscrews to secure rails during storage
6. Rail lockers

Dimension-19 inch

Model

| Product Dimension (W x D x H)| Packing Dimension (W x D x H)| Net Weight| Gross Weight
---|---|---|---|---

19″ monitor

| ****

448 x 558.8 x 44 mm

| ****

790 x 580 x 190 mm

| ****

17.5 kg

| ****

21 kg

The weight is only for the pure models. It varies with accessories & options such as SDI, HDMI, audio, touchscreen & DC power.

Product Specifi cations

LCD

Panel

| Panel Size ( diagonal )| 19”
---|---|---
Display pixel ( dots x lines )| 1280 x 1024
Brightness ( typ. )| 450
Contrast Ratio ( typ. )| 1000:1
Color| 16.7M
Viewing Angle ( H/V )| 170/160
Response Time ( ms )| 5
Backlight Type| LED
Video Connectivity| Digital| HDMI (option)| HDMI 1.1, CEA-861-D
---|---|---|---
DVI| DVI-D, TMDS single link
Analog| VGA| Analog 0.7Vp-p
Plug & Play| DVI / VGA| VESA EDID structure 1.3
Synchronization| VGA| Separate, Composite & SOG
Audio Connectivity| Audio Input| Connector| 3.5mm stereo jack
---|---|---|---
Impedance / Power level| 30k Ω / 750mV
Speaker Output| Power| 2 x 2W
Power| Power Supply| Range| Auto-sensing 100 to 240VAC, 50 / 60Hz with lock connector
---|---|---|---
DC Power| Range| 9~36V DC with lock connector
Regulatory| Safety| FCC & CE certified
---|---|---
Environmental| RoHS2 & REACH compliant
Environmental Conditions| Operating| Temperature| -20 to 70°C degree
---|---|---|---
Humidity| 5~95%, non-condensing
Storage / Non-operating| Temperature| -30 to 80°C degree
Humidity| 5~95%, non-condensing
Shock| 15G / Peak (11 ms)
Vibration| 5 – 500 Hz / 1 Grms PTP
Applicable Format| DVI-D / VGA Input| PC Signal| 1280 x 1024 x 60 / 75Hz
---|---|---|---
1280 x 960 x 60Hz
1280 x 768 x 60 / 75Hz
1152 x 864 x 75Hz
1024 x 768 x 60 / 70 / 75Hz
848 x 480 x 60Hz
800 x 600 x 60 / 72 / 75Hz
720 x 400 x 70Hz
640 x 480 x 60 / 72 / 75Hz
640 x 400 x 70Hz
640 x 350 x 70Hz

On-screen Display Operation ( OSD )
LCD OSD can establish and set up LCD displays. The setup instructions of the four buttons are as follows:

Options: Touchscreen
USB Touchscreen Specifi cation

Technology Touch Point Method Activation Force Durability Response Time

Optical Transmittance Surface Hardness Haze

Glass Connector

Compatibility

| 5-Wire Resistive
Single
Stylus or Finger
≤ 50g / Stylus=R0.8
10 million touches
15 ms
80% ± 3%
3H
8% ± 3%
3.2 ±0.2 mm
USB Type A
Windows 7 / XP / Vista, Linux

• USB touchscreen package includes 1 x 1.8 M USB cable
• For detailed information, please refer to the attached CD disc
• As the touchscreen unit is not made of toughened glass, please handle it carefully

Options : DC power

Crystal Image Technologies, Inc. 800-542-2489 sales@rackmountsales.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>