Train Tech SK8 Dual Head Yellow Green Self Assembly Signal Kit User Guide

: June 13, 2024
: Train-Tech

Table of Contents

Introduction
Assembling the kit
Connecting the signal
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SK8+ Dual head Home Yellow-Green
Signal self assembly kit

CAUTION – ALWAYS SWITCH OFF POWER TO YOUR LAYOUT BEFORE CONNECTING OR DISCONNECTING ANY ACCESSORIES
This Self assembly signal kit contains an plastic kit, post and LED Light circuit board with resistors to make a Colour Light signal designed for use on OO/HO gauge model railways – please read these instructions before assembly and connecting to power.

Introduction

Contents
1 Plastic Signal kit
1 Additional 2 aspect head and cover
1 Aluminium signal post
1 Signal LED lights printed circuit board ‘PCB’
4 1KΩ resistors (Colour:Black Brown Red Gold)
1 Instruction leaflet
Recommended tools (not included)
Sharp craft knife or cutters
Small needle file, tweezers or small pliers
Adhesives to suit plastic/metal (see below)
Magnifier
Cutting mat
Thank you for purchasing one of our self assembly signal kits. This kit is an all new design based on an actual colour light signal near our base in Norfolk and is fairly typical of British outline colour light signals and designed to scale with the red light in line with the train drivers eye, just like the real thing. We have utilised the latest LEDs for the lights but unlike most signal kits we have presoldered them on narrow printed circuit boards which makes themmuch easier to assemble and connect. They are also more realistic being uncoloured until lit and have an integral lens so they shine brighterfaced from the front.
You can either control this signal using conventional Lever frame or Toggle type switches or connect it to a DCC decoder to control it from a Digital controller or computer.
(note that Train-Tech also offer this signal with abuilt-in DCC decoder which just plugs straight into the track – no wires or circuitry!)
Take extra care when using tools and adhesives.
Construction advice
The plastic part of this kit is made of a blend of mostly ABS which is slightly more forgiving and less brittle than the polystyrene often used for plastic kits. However it can still be glued together using most general model kit adhesives such as Humbrol or Revell Liquid Poly or ‘super glue’ – be sure to follow instructions for application and safety supplied with the adhesive. Note that if fixing accessories to the aluminium post, such as the phone or sign, you will need to use a glue which is suitable for bonding plastic to metal.
To remove parts from the sprue we suggest using either precision wire/model cutters (available from dcpexpress.com and model or tool suppliers) or a sharp knife working on a scrap of wood or cutting mat. Some fragile parts, such as the ladder, may be more easily prepared by first removing the part with its larger plastic moulding supports attached, then carefully removing the part from the supports.
If you wish to paint any parts most model enamel paints should work fine but if unsure check on a small piece of scrap plastic first. Please note that we cannot help customers assemble kits, but if you have difficulties making kits we suggest you try contacting your local model club for assistance.
We recommend first cutting thicker supports to release main parts then trimming off the small supports using a sharp craft knife or cutters Mounting the signal on your baseboard
You will need to drill a hole in your baseboard to clear the signal PCB – we recommend a 6-8mm hole so that the signal can be lifted with wires still fitted if required. The signal can be free standing or held by suitable glue or double sided sticky pad.
Document Ref D779688/4

Assembling the kit

The exploded diagram below shows all the various components which go to make up a complete signal, although you can fit as few or as many of the detailing parts as you wish for your model.
We recommend you read the construction advice below on how to remove parts, adhesives etc.
Suggested order of assembly:

Slide LED PCB through slot in dual head mount
Push fit or glue head mount onto aluminium post
Push fit post into main base plate and align
Glue front and back head covers around LED’s
Dry fit or glue ladder between head mount & base
Glue base cover under base if desired
Glue handrails, phone, location board if desired

Wiring advice
Electrical connection to the signal is via metal ‘pads’ at the bottom of the LED light PCB. These pads are made from thin copper bonded to the fibreglass and then ‘tinned’ to ensure reliable and easy connection.
The best method of connection is by soldering wires onto these pads using a small tip soldering iron of 18-25 watts, taking care not to apply heat for too long. Note that by pre-tinning wires before soldering onto the pads you will find that the solder will flow much more easily to make a secure joint quickly.
If you prefer not to solder then you can wrap thin stranded wire around the pads by stripping off insulation, twisting strands tightly together and wrapping them round the signal base and tightly binding insulation tape around each joint. However soldering is the preferred and most reliable method.
Whichever method you use take care not to let the wires short circuit to each other and do not forget to fit a resistor in series as shown before powering up your new signal!
Location board labels
These legends can be cut out and glued to the model Location board on the plastic detailing sprue.
If using DCC we suggest you use the address you have programmed into your signal decoder which will make the signal easier to identify and operate.

Connecting the signal

The LED lights are presoldered onto a PCB which has large contacts at the base to connect your wires to. You can either control it by conventional Lever or Toggle switches or alternatively a digital decoder (eg Train-Tech SC1 which can control two 2 aspect signals) if you wish to control it using a DCC controller or computer – follow the connection instructions supplied with the decoder.
You MUST fit resistors as shown below and power from a DC supply or DCC decoder or you will cause permanent damage to the LEDs
(Unless using with Train-Tech DCC Signal controllers which incorporate resistors inside)
IMPORTANT NOTE
The terminals on this SK+ kit have changed since the original signal kits to add connections for fitting feather and theatre route indicators, so please refer to the wiring diagram below. Using LEDs with model railways
The lights used in this signal kit are called LEDs.
LEDs are really useful lights which, unlike their conventional filament predecessors, are robust, low power and if used correctly run cool and can effectively last forever.
But there are some important considerations when using LEDs. Firstly LED stands for Light Emitting Diode and a diode is an electronic component which only works in when power is applied in one specific direction, so they always need to be fitted the correct way round to work correctly.
Also most standard miniature LEDs a modeller will use only need very small amounts of power, so the current flowing through the LED must be limited and this is usually done by a resistor as supplied in this kit. On the usual 12-16 volts DC supply a railway modeller uses a 1kΩ (one thousand ohms) will limit the current to around 10-14mA (mA is thousandths of an amp) which is ideal for most LED’s.
Note you should only ever use LEDs on a DC (direct current) supply and never an AC (alternating current) supply because although the LED may appear to work properly constant reversal of voltage using AC will eventually damage or shorten its life.
Train-Tech offers packs of various LEDs for modellers and again these always come with both instructions and suitable resistors for using them on a standard Model Railway DC supply or non TrainTech DCC controllers.
Using Signals with Train-Tech DCC controllers
Train Tech offer various LED controllers including the SC1 and SC2 DCC signal controllers which allow signals such as this to quickly and easily connect to DCC layouts for control by Digital controller or computer. They are quick to connect needing no resistors or soldering and set up in seconds with no programming of CV codes.
As well as Signal Controllers, Train-Tech also makes a range of LFX LED lighting controllers which work on both DC and DCC and offer effects to simulate level crossings, welding, traffic lights etc – again resistors are built into all of the LFX units and so LEDs connect directly to them.
See www.train-tech.com for full details.
Track Tester

Quickly tests track for power faults
Low cost and easy to use
Works on N, TT, OO or HO Track
Indicates the DC polarity, or DCC, or a fault
Small enough to check point frogs
Buffer Lights
Add realistic stop light to any siding
Simply clips onto track – No wires!
Fits next to most buffer stops & kits
Or at platform end or free standing
On DCC both lights are on constantly
On DC one light is on & varies with speed
DCC Fitted Digital Signalsc
Signal with DCC decoder built into base
Can just plug direct into track – no wires!
Easy to ﬁ t and use – no CV programming!
Can sync to other signals & points
Available with Feathers & Theatres
One-Touch DCC™ Point Controllers
Control points and uncouplers using DCC
Work with most solenoid point motors
Just connect 2 wires to DCC rails – No CV Programming!
Easy screw terminals – no soldering
Built in CDU for efﬁ cient operation
Can sync to other points and signals
LFX Lighting Effect Controllers
Easily add lighting effects to your layout
LEDs screw in – no resistors or soldering
Powered by 9v battery, 9-16V DC or DCC
On DC the effect is on when powered
On DCC the effect can be controlled
Effects LEDs are included
Level Crossing – Ready Assembled
Power from 9-16v DC, DCC or a 9v battery
Light and sound – all connections easy push ﬁ t
Includes 2 x Peco static level crossing barriers
Can turn on automatically using a Track Sensor
Available in single and pair packs
Track Sensor
Change Semaphore Signals automatically (with SC300)
Trigger Level crossing when train approaches
Power from 12-16v smooth DC or DCC
Links to a Mimic Switch to show occupancy
Links to a Sensor Signal to change block section
Automatic Tail, Firebox & Loco Lights
No switch – senses motion & turns on!
Turns off automatically 4 minutes after stop
No pickup, wires or soldering – LED plugs in
Fit in brake vans, coaches, loco, wagons etc
Runs for ages on small button battery
LEDs and batteriy included
Mimic Switches & Lights
Make a mimic panel to control LayoutLink items
Link to Track Sensors or Sensor Signals to show occupancy & signal status
Single wire to control Layout Link products
Link to Sensor Signals to switch route indicators on/off
Signal Kits Every kit includes the signal head, aluminium post and base plus detailing kit
Low cost – adapt to your own design
Control by switches or signal controller
LEDs are preﬁ tted to a narrow PCB One-Touch DCC™ Signal Controllers
Control LED & Semaphore signals by DCC
Easy to set up & use –No CV programming!
Easy screw terminals – no soldering
Can sync to other points & signals
Automatic Sensor Signals
Detects train and changes signal automatically
Use on its own & signal changes back to green after time
Or link to other SS for automatic block signalling
Can be used on both DC & DCC
Also available with Feathers & Theatres
Automatic Coach Lighting
Easy to ﬁ t in seconds – no wiring!
No switch – senses motion & turns on!
Turns off automatically 4 minutes after stopping
No pickups so works on regular DC & DCC
Traditional warm white or modern cool white
Also with tail light, sparks or door light effect
Lights stay bright & constant with no ﬂ ickering
Fits most OO/HO coaches and maybe cut down
SFX Sounds for Trains
Easy low cost sound that works on any railway
Easy to ﬁ t in seconds – no connections
No switch – senses motion & turns on!
No pickups so works on regular DC & DCC
Self contained – built in speaker & battery (included)
Tiny capsule: 25mm x 20mm x 12mm approx
Fit capsule into loco, tender, wagon, coach…
Real recorded sounds – Steam & Diesel etc
Smart Lights – Easy to ﬁ t Lighting Effects
Small – Just 1cm x 1cm x 0.3cm with 2 wire connections
Power by standard 9-16v DC or a 9v battery
Or by DCC which can also control some effects
Just connect and go – no setting up required
Disco / Emergency / Real Fire / TV / Welding / Random effects
Trafﬁ c Lights – Ready Assembled
Power from 9-16v DC, DCC or 9v battery – 2 Wire connection
Realistic standard UK sequence and timing varies randomly
Fully assembled – drill hole in baseboard & connect to power

SEE WWW.TRAIN-TECH.COM OR CONTACT DCP FOR FREE COLOUR BROCHURE

SK8+: Dual head Yellow-Green
Self assembly signal kit
www.Train-Tech.com
See our website, your local model shop or contact us for a free colour brochure
DCP Microdevelopments, Bryon Court, Bow Street, Great Ellingham, NR17 1JB, UK
Telephone 01953 457800
email sales@dcpmicro.com
www.dcpexpress.com