WTA Sprinter High Roof Side Ladder Installation Guide

WTA Sprinter High Roof Side Ladder

Product Information

The WTA Sprinter Side Ladder is a product designed to be securely attached to your vehicle. It is important to properly assemble and inspect the mounting points and attachments before use to ensure safety. The ladder comes with all necessary components for installation, including ladder halves, screws, nuts, washers, and a mount plate.

Package Contents:

• Ladder Bottom – Quantity: 1
• Ladder Top – Quantity: 1
• M6-30 Hexagon Head Screw – Quantity: 4
• M10-22 Hexagon Head Screw – Quantity: 2
• M10-30 Hexagon Head Screw – Quantity: 2
• Mount Plate – Quantity: 1
• M6-16 Button Head Screw – Quantity: 4
• M6 Flat Washer – Quantity: 8
• M10 Spring Lock Washer – Quantity: 2
• M10 Nylock Nut – Quantity: 2
• Rail Nut – Quantity: 2
• M6 Nylock Nut – Quantity: 4
• M10 Flat Washer – Quantity: 4

Product Usage Instructions

1. Place the ladder halves front side down and insert the couplers into one half. Tighten them down using the M6-16 screws.

2. Slide the other ladder half onto the couplers and tighten them down. Optionally, you can use blue Loctite on the screws.

3. Slide the two rail nuts into the roof rail of your van. Note that if you’ve already installed a roof rack, this step may be time-consuming.

4. Position the ladder on the van, hanging it on the roof rail.
   Loosely screw the top of the ladder down to the roof rail using the M10-22 screws, M10 spring lock washers, and M10 flat washers.
   Tighten it just enough to make it snug.

5. Take the mount plate and loosely attach it to the bottom of the ladder using the M10-30 screws, M10 flat washers, and M10 nylock nuts. Ensure that the ladder is straight up and down.

6. Using a drill bit, create holes in the pinch weld for supporting the mount plate.

7. Support the mount plate onto the pinch weld using M6 bolts and nuts.

8. Support the ladder to the mount plate using M10-30 bolts and nuts.

Sprinter Side Ladder
It is crucial to ensure that all WTA products are assembled and securely attached to your vehicle. Failure to do so may result in automobile accidents, posing a significant risk of bodily injury or even death to yourself and others. As the owner, it is your responsibility to properly assemble and secure WTA products, diligently inspecting the mounting points and attachments before use, and regularly checking for any signs of wear or damage.
To guarantee optimal safety, we strongly advise engaging the services of a professional installer for the installation of any aftermarket accessories to your vehicle. If you lack mechanical experience or are unfamiliar with the installation procedures, it is imperative to have the product installed by a qualified professional or individuals who possess the necessary expertise. Remember, the responsibility lies with you, and it must be taken seriously to ensure the safety of all individuals involved.

PACKAGE CONTENTS

INSTRUCTION

LET’S GET STARTED

1. PLACE THE LADDER HALVES FRONT SIDE DOWN, INSERT THE COUPLERS INTO ONE HALF (SEE FIGURE 1), AND TIGHTEN DOWN USING THE M6‐16 SCREWS.

2. SLIDE THE OTHER LADDER HALF ONTO THE COUPLERS AND TIGHTEN DOWN. NOTE‐ IF DESIRED YOU CAN USE BLUE LOCTITE ON THE SCREWS.

3. NEXT, SLIDE THE TWO (2) RAIL NUTS INTO THE ROOF RAIL ON YOUR VAN. NOTE- IF YOU’VE ALREADY INSTALLED A ROOF RACK, THIS MAY BE TIME CONSUMING.

4. NOW POSITION THE LADDER ON THE VAN, HANGING IT ON THE ROOF RAIL. LOOSELY SCREW THE TOP OF THE LADDER DOWN TO THE ROOF RAIL USING THE M10-22 SCREWS AND THE M10 SPRING LOCK WASHERS AND M10 FLAT WASHERS JUST ENOUGH THAT IT IS SNUG (SEE FIGURE 3)
   NOTE- WE LIKE TO PLACE THE LADDER AS CLOSE TO THE REAR WHEEL WELL AS WE CAN. SEE IMAGE BELOW.

5. TAKE THE MOUNT PLATE (SEE RIGHT) AND LOOSELY ATTACH THEM TO THE BOTTOM OF THE LADDER USING THE M10‐30 SCREWS,M10 FLAT WASHERS, AND M10 NYLOCK NUTS.
   NOTE‐ MAKE SURE THAT THE LADDER IS STRAIGHT UP AND DOWN.

6. Line up the support plate with the ladder and drill 5 holes with ¼ inches drill bit.

7. Support the plate on to the pinch weld with M6 bolt and nuts.

8. Support the ladder to the support plate using M10‐30 bolts and nuts.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>