WTA SPRR144-J Sprinter High Roof Strata Roof Rack Installation Guide
- June 2, 2024
- WTA
Table of Contents
WTA SPRR144-J Sprinter High Roof Strata Roof Rack Installation Guide
Ensuring the proper assembly and secure attachment of all WTA products to your vehicle is of utmost importance. Failure to adhere to these guidelines may lead to automobile accidents, presenting a substantial risk of bodily harm or even fatality to yourself and others. As the owner, it is incumbent upon you to meticulously assemble and secure WTA products, conducting a thorough examination of the mounting points and attachments before use, and routinely checking for any indications of wear or damage.
To ensure optimal safety, we strongly recommend enlisting the services of a qualified installer for the installation of any aftermarket accessories on your vehicle. If you lack mechanical expertise or are unfamiliar with the installation procedures, it is crucial to have the product installed by a certified professional or individuals with the requisite skills. Remember, the responsibility rests with you, and it must be approached with seriousness to safeguard the well-being of all individuals involved
Descriptions
| 描述 | B O M | QTY |
|---|---|---|
| RIVER FRONT RAIL | 1 | 1 |
| PASSENGER FRONT RAIL | 2 | 1 |
| RIVER REAR RAIL | 3 | 1 |
| PASSENGER REAR RAIL | 4 | 1 |
| FRONT ARMOR PLATE 1 | 5 | 2 |
| REAR ARMOR PLATE | 6 | 2 |
| JOINT PLATE | 7 | 2 |
| FAIRING PLATE | 8 | 1 |
| CROSSBAR | 9 | 6 |
| M 8 -20 HEXGON SOCKET BUTTON HEAD SCREW | 1 0 | 1 |
| M 8 -25 HESGON SOCKET BUTTON HEAD SCREW | 1 1 | 24 |
| M 8 *16 FLAT WASHER | 1 2 | 82 |
| M 8 SPRRING LOCK WASHER | 1 3 | 82 |
| M 10-22 HEXGON HEAD SCERW | 1 4 | 12 |
| SQUARE NUT | 1 5 | 12 |
| M10 FLAT WASHER | 1 6 | 12 |
| M10 SPRING LOCK WASHER | 1 7 | 12 |
| T SLIDE NUT | 1 8 | 10 |
| M8-12 HEXGON SOCKET BUTTON HEAD SCREW | 1 9 | 10 |
| LOCK NUT | 20 | 20 |
THANK YOU!
- PLEASE INSPECT THE PRODUCT TO ENSURE THERE WAS NO DAMAGE INCURRED DURING SHIPPING.
- IF THERE IS DAMAGE TO REPORT, PLEASE CONTACT OUR CUSTOMER SERVICE DEPARTMENT AS SOON AS POSSIBLE.
- NEXT, USING THE “PACKAGE CONTENTS” PAGE, CHECK INVENTORY AND FAMILIARIZE YOURSELF WITH THE PARTS AND HARDWARE.
- GATHER ALL TOOLS REQUIRED FOR INSTALL.
-10 mm WRENCH
-17 mm WRENCH
TOOLS
-
10 mm Wrench
-
17 mm Wrench
PACKAGE CONTENTS
-
DRIVER FRONT RAIL
QTY-1
-
DRIVER REAR RAIL
QTY-1
-
PASSENGER FRONT RAIL
QTY-1
-
PASSENGER REAR RAIL
QTY-1
-
FAIRING
QTY-1
-
JOINT PLATE
QTY-2
-
T BLOCK
QTY-8 -
CROSSBAR
QTY-6
HARDWARE PACK
AADP144| RAIL NUT QTY-12
| M10-22 HEXGON HEAD SCREW QTY-12
| **** M8-12 HEXGON SOCKET
BUTTON HEAD SCREW QTY-10
| M8-20 HEXGON SOCKET
BUTTON HEAD SCREW QTY-48
---|---|---|---|---
| **** M10 SPRING LOCK WASHER QTY-12
| M8 SPRING LOCK WASHER QTY-82
| M8-25 HEXGON SOCKET
BUTTONHEAD SCREW QTY-24
| **** M10 WASHER QTY-12
| **** M8 WASHER
QTY-82
|
LET’S GET STARTED!
-
SLIDE HALF OF THE RAIL NUTS INTO THE PASSENGER SIDE FACTORY ROOF RAIL, AND HALF OF THEM INTO THE DRIVER SIDE RAIL.
-
SPACE OUT THE RAIL NUTS CLOSE TO THE FINAL POSITION (GROUPS OF 2) SEE FIGURE 1 FOR ROUGH REFERENCE DIMENSIONS.
USE THESE DIMENSIONS FOR ROUGH REFERENCE ONLY (UNIT: mm) -
START LOOSELY ATTACHING THE SIDE RAILS TO THE ROOF RAILS USING THE M10-22 HEXGON HEAD SCREW & M10 SPRING LOCK WASHERS & M10 WASHERS, BUT DO NOT TIGHTEN ALL THE WAY DOWN.
(SEE FIGURE 3 FOR DETAIL)
-
PLACE YOUR CROSSBARS IN DESIRED LOCATION, LOOSELY BOLTING THE M8-20 HEXGON HEAD SCREWS & M8 SPRING LOCK WASHERS & M8 WASHERS IN PLACE.
NOTE- IF INSTALLING OUR FRONT FAIRING; IT IS SUGGESTED TO BOLT THE FAIRING TO THE CROSSBAR FIRST (SEE FIGURE 5),
THEN ATTACH THAT ASSEMBLY TO THE ROOF RACK (SEE FIGURE 6)
-
TIGHTEN ALL CROSSBAR BOLTS USING THE 10 mm WRENCH
NOTE- DO NOT OVERTIGHTEN! IF YOU ARE CONCERNED ABOUT THE BOLTS BACKING OUT, YOU CAN PUT A DAB OF BLUE LOCTITE ON THE BOLTS BEFORE TIGHTENING DOWN COMPLETELY.
-
NOW TIGHTEN SIDE RAILS TO ROOF RAIL USING THE 17 mm WRENCH
GET THERE WITH WHITE TOP ADVENTURES
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>