Country Living CL-M-WB-2301 Jackson Electric Fireplace Mantel Package Instruction Manual
- June 13, 2024
- Country Living
Table of Contents
Country Living CL-M-WB-2301 Jackson Electric Fireplace Mantel Package
SAFETY INFORMATION
- Please read and understand the entire manual before attempting to assemble, install, or operate the product.
- WARNING! You may need an adult to assist with some steps.
- CAUTION!
Before assembly and installation, carefully unwrap all parts. Locate and set aside the hardware kit before disposing of the packaging. Use care when assembling the product. Take your time and follow the instructions closely.
WARNING!
Do not use more than the maximum load as shown in the diagram. The use of
TVs or loads heavier than the maximum weights specified may result in
instability, causing tip over, which could result in serious injury or death.
Questions, problems, missing parts?
Before returning to store, call
Customer Service:
8am-5pm CST, Monday – Friday
- Phone: 877-430-0703
- Email: resolutions@electricfireplacesdirect.com
- Please save these instructions for future reference.
TOOLS NEEDED
PARTS
PART NO.| DESCRIPTION| QTY
1| Top| 1
2| Header| 1
3| Left Side| 1
4| Right Side| 1
5| Base| 1
HARDWARE
SAFETY STRAP KIT
INSTALLATION INSTRUCTION
STEP 1
Gently set the left side panel (3) and right side panel (4) on the base (5) as shown in the diagram. Place a gasket (C) on each long bolt (A), and then add a gasket (B) to each bolt. Align the holes on the base (5) with the holes on the side panels (3 & 4). Insert a bolt from the bottom into a hole on the base. For the top of the bolt (A), add a gasket (B) followed by a gasket (C). Add a butterfly nut (D), but do not tighten. Repeat for the other 3 holes. You will tighten the butterfly nuts (D) in Step 5. Do not tighten them before or the mantel parts will be misaligned.
STEP 2
On each long bolt (A), place a gasket (C) and then a gasket (B). Carefully set the header (2) on the top of the side panels (3 & 4), making sure the holes are aligned. From the bottom of the header (2), insert a long bolt (A) into a hole. On the bolt, add a gasket (B), followed by a gasket (C). Add a butterfly nut (D), but do not tighten. Repeat for the other 3 holes. You will tighten the butterfly nuts (D) in Step 5. Do not tighten them before or the mantel parts will be misaligned.
STEP 3
Place a gasket (C), then a gasket (B), on each short bolt (E). Carefully set the top (1) onto the header (2), making sure the holes are aligned. Using a screwdriver, install a bolt (E) into a hole from the bottom of the top (1), but do not tighten. Repeat for the other 3 holes. You will tighten the butterfly nuts (D)in Step 5. Do not tighten them before or the mantel parts will be misaligned.
STEP 4
- Carefully place the electric fireplace insert on the base of the mantel.
STEP 5
Using the screwdriver, secure the fireplace insert to the mantel with the included screws (F). Make sure the base (5), panels (3 & 4), header (2), and top (1) are in the correct positions. Tighten all the butterfly nuts (D) from steps 1, 2, and 3.
STEP 6
WARNING: This tip restraint must be attached to a wall stud using the 50mm screw (J) enclosed.
- Attach one bracket (H) securely to the back top wood panel of the mantel using the 16mm screw (K) through the smaller hole of the bracket. It is highly recommended to pre-drill a 1/16″ hole into the wood mantel to prevent splitting.
- Position the other bracket (H) on the wall over a wall stud 2 inches below the bracket secured to the back of the mantel. Attach to the wall stud using the 50mm screw (J) through the smaller hole of the bracket.
- Place the mantel into position so both brackets are in line vertically.
- Lace the end of the restraint strap (I) through the larger hole in each bracket. Bring both ends together and slide the flat end through the locking end. Pull it through until all slack is removed.
- Confirm that the strap is securely laced and locked.
Questions, problems, missing parts?
Before returning to store, call
Customer Service:
8am-5pm CST, Monday – Friday
- Phone: 877-430-0703
- Email: resolutions@electricfireplacesdirect.com
- Please save these instructions for future reference.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>