lubluelu SL68 Robot Vacuum Cleaner Instruction Manual

lubluelu SL68 Robot Vacuum Cleaner

Product Information

The Robot Vacuum Cleaner is a versatile cleaning device designed to efficiently clean your floors. It comes with various features and components to ensure effective cleaning.

• Main Unit: The main unit of the vacuum cleaner houses the essential components and controls.
• RESET System Reset Button: This button allows you to reset the device using a needle.
• Sensor and Structure: The vacuum cleaner is equipped with a laser radar, infrared receiver sensor, bumper, cliff sensor, charging contact, universal wheel, side brush, battery cover, drive wheel, and rolling brush.
• 2in1 Dustbin & Water Tank: The vacuum cleaner has a combined dustbin and water tank for efficient cleaning.
• High-efficiency Filter: The vacuum cleaner includes a high-efficiency filter, sponge filter, and primary filter for effective filtration.
• Charging Base: The charging base is used to charge the vacuum cleaner and includes a power status light, infrared signal emitter, power socket, and charging shrapnel.

About Robot

What’s in the Box

Main unit

Sensor and Structure

2in1 Dustbin & water tank

Charging Base

Installation

Precautions

1. Remove the protection material from both sides of the robot.

2. Install side brushes
   Put the left side brush L and right side brish R against the letters L on the bottom shell respectively, and press down, you will hear a “click” sound, and it means that the side brushes are installed in place.

3. After connecting the power adapter to the power supply, connect it to the charging base and tidy up the redundant wires.

4. Place the charging base on flat ground against the wall and connect to the power supply.

5. Don’t move the charging base at will; avoid direct sunlight on the charging base.
   Note: The sunlight may interfere with the recharging signal, which may cause the robot vacuum cleaner to fail to return to the charging base.

6. Power on and charge
   Press and hold the button to power it on. When the indicator light is normally on, put the main unit against the charging base for charging; when you hear the voice of “Start charging”, it means that the robot is being charged successfully.

Installation[Mopping function]

1. Open the water injection cover, add the appropriate amount of water, and then cover tightly, please do not add any detergent.
2. Put the water tank back into the robot.
3. Install the mop on the mop support.
4. Install the mop support.

APP Connection

Preparation before connection

Use Instructions

Power on/Power off
Press and hold the button for 3 seconds, and if the indicator light is lit in, it means the machine is started up successfully When the robot vacuum cleaner is in stand by state, press and hold the button for 3 seconds, and if the indicator light goes out, it means the machine is shut down.
Note: The robot vacuum cleaner cannot be shut down during charging.

Clean / Pause
After startup, press the key on the main unit or use the remote controller or mobile APP to start cleaning.

Note:

• The robot vacuum cleaner cannot be used to clean liquid.
• If the battery capacity is less than 15%, the robot cannot work; therefore, charge the machine before cleaning.
• When the battery capacity is less than 15% in the cleaning process, the device will automatically return to the charging base for charging.
• Please tidy up the wires （including the power line of the charging base) on the ground before cleaning; otherwise, the wires may be dragged when the machine is cleaning which may cause power failure to electric appliances and damage items or wires.

Charge

• Automatic mode: After finishing cleaning, the robot vacuum cleaner will automatically return to the charging base for charging.
• Manual mode: In the pause state, press the button to start recharging or use the remote controller or mobile APP to start recharging.

Note: If the robot vacuum cleaner fails to find the charging base, it will automatically return to the starting point; please manually put back the main unit on the charging base for charging.

Suction selection
Use the mobile APP to select energy-saving, standard, and powerful modes (the default is standard mode).

Intelligent cleaning (default mode)
The robot vacuum cleaner scans the working environment, generates a map, and intelligently divides the areas. It will complete cleaning of each area one by one by filling along the Z shape behind the wall, After finishing cleaning, the robot vacuum cleaner will return to the charging base for charging. In order to better build the map, the robot needs to start from the charging base at the first cleaning.

Note: Do not move the main unit randomly and frequently during operation, After moving, please put the main unit near the original place. When starting the machine again, the device will try to reposition its coordinates; after positioning successfully, it will continue to work according to the planned path; if positioning fails, the device will give up the previous task, and build a new map for cleaning, but it might fail to recharge.

Cleaning as required
Use the mobile APP to select the function of cleaning as required select a point on the map and the robot vacuum cleaner will move to the designated position and clean a 1.6m x 1.6m square area with itself as the center.

Note: Before using this function, complete the building of the map for the first cleaning in the mobile APP.

Cleaning of the selected area
Use the mobile APP to select the function of cleaning of selected area, select the area to be cleaned on the map and the robot vacuum cleaner will clean in the selected area.

Note:

• Before using this function, complete the building of the map for the first cleaning in the mobile APP.
• The main unit might enter the unplanned area, so please clear the obstacles on the ground around the planned area, and this area cannot play a role of safety isolation.

Cleaning of a defined area
Use the mobile APP to select the function of cleaning of defined area, select the area to be cleaned on the map and the robot vacuum cleaner will clean in the defined area.

Note:

• Before using this function, complete the building of the map for the first cleaning in the mobile APP.
• The main unit might enter the unplanned area, so please clear the obstacles on the ground around the planned area, and this area cannot play a role of safety isolation.

Restricted area setting
Use the mobile APP to select the restricted area editing function, select and set the restricted area of cleaning on the map, and the machine will not enter the set area to clean.

Note:

• Before using this function, complete the building of the map for the first cleaning in the mobile APP.
• This function is only used to define the cleaning areas and cannot be used to block dangerous areas.
• When moving the robot vacuum cleaner or there are obvious changes in your home environment, the map might become ineffective and the restricted area might be lost.

Scheduled cleaning
After the setting of scheduled cleaning takes effect, the machine will automatically start to clean at the designated time, and automatically return to the charging base after finishing cleaning.

DND mode
The default starting time period is 22:00-06:00, Which can be modified or closed in your mobile APP. During the DND time period, the robot vacuum cleaner will close the functions of automatic continuous cleaning, actively playing the voice, and timing.

Other APP functions

Routine Maintenance

Rolling brush (Recommended cleaning frequency: once a week)

1. Turn over the machine, press the buckle on the rolling brush cover, and take out the cover plate of the rolling brush.
2. Take out the rolling brush.
3. Use the clean brush to remove the dust in the cavity of, the main brush and rolling rush and clear the entanglements on the rolling brush.

Side brush (Recommended cleaning frequency: once a week)

1. Turn over the machine upward and pull out the side brush vertically.
2. Clear the entangled hairs and install the side brush.
3. Align the side left brush (L) and right side brush (R) with the letters L and R on the bottom shell respectively, and press them down to install back the side brush.

Note: It is recommended to replace the side brush every three months to ensure a cleaning effect.

Dust bin and filter (Recommended cleaning frequency: after cleaning)

1. Press the dust bin button and draw out the dust bin.
2. Press the dust bin switch and open the dust bin to dump the rubbish.

Wash the 2in1 Dustbin & water tank (Recommended cleaning frequency: after cleaning)

1. After use for a long time, take down the sponge and high-efficiency-filter.
2. Flush the primary filter, dust bin, and sponge under the water tap the high-efficiency-filter cannot be washed with water.
3. After washing, shake off the water drops, dry the filter and dustbin in the air, and they can be used only after they are completely dry.

Note:

• Wash with clear water and do not add any detergent.
• Do not use a brush but use fingers to clean the filter.
• The filter shall be dried in the air for at least 24 hours so that it can be dried thoroughly.
• It is recommended to replace the filter every three months.

Clean the infrared obstacle avoidance sensor
(Recommended cleaning frequency: once a month)

Clean the cliff sensor
(Recommended cleaning frequency: once a month)

Clean the charging contact
(Recommended cleaning frequency: once a month)

Clean the signal emission region on the charging base
(Recommended cleaning frequency: once a month)

Battery

• A rechargeable high-performance lithium-ion battery pack is built into the main unit. To maintain the battery performance, please maintain the main unit in a charging state during daily use
• If the machine is not used for a long time, it shall be shut down for storage and charged every three months to avoid damage to the battery due to over-discharge

Firmware upgrade
Enter the firmware upgrade function through the mobile APP. After new firmware is detected, upgrade according to the prompt guidance. The battery capacity shall not be less than 50% during the firmware upgrade. It is recommended to place the device on the charging base during the upgrade.

Basic Parameters

Common Problems

Troubleshooting

Safety Information

Use Restrictions

• This product can only be used for floor cleaning at home. Please do not use it in outdoors (such as on an open balcony), non-ground (such as a sofa), commercial or industrial environments.
• Do not use the machine in suspended environments without protective fences (such as duplex floor, open balcony, and top of furniture).
• Do not use the machine in an environment where the temperature is higher than 40℃ or lower than 0℃ or there are liquid and viscous objects on the ground. Please hang up the ground wires at home before use to avoid dragging the wires when the main unit is running.
• Please put away the fragile articles and sundries (such as vases, please bags, etc.) on the ground; otherwise, the machine may be blocked or a slight collision may cause damage to valuables at home.
• Do not allow people (including children) with physical, mental, or perceptual disabilities to use or operate this product.
• Do not allow children to use the machine as a toy. When the machine is working, please keep children and pets away from the machine.
• Keep the cleaning brush out of reach of children.
• Do not place any objects (including children and pets) on the stationary or moving machine.
• When the machine is working, keep the hair, fingers, and other parts of the human body or pet away from the dust suction inlet of the machine.
• Do not use the machine to clean burning objects such as burning cigarette butts.
• Do not use the machine to clean long-haired carpets. Some dark carpets might not be cleaned normally).
• Do not use the machine to vacuum hard or sharp objects, such as decoration waste, glass, nails, etc.
• Do not use the protective cover of the laser ranging sensor or bumper as a handle to carry the machine.
• Please clean or maintain the machine and charging base when the machine is shut down or powered off.
• Do not use a damp cloth or any liquid to wipe any part of the machine.
• Please follow the instructions in the manual when using the machine. Any loss and injury caused by improper use of the product shall be borne by the user. Do not use the mopping function on the carpet or the top furniture.
• Remove the water tank when charging the machine.

Battery and Charging

• Do not use any third-party batteries, charging bases, or chargers.
• Do not disassemble, repair, or modify the battery or charging base without permission.
• Do not place the charging base near heat sources such as heating radiators.
• Do not use a damp cloth or wet hands to wipe or clean the charging base shrapnel.
• Dispose of used batteries properly and send them to professional recycling agencies.
• If the power line is damaged or broken, stop using it immediately and buy a new one through official channels.
• When transporting the product, ensure that the machine is shut down, and it is recommended to use the original packaging box for packaging.
• If you do not use the machine for a long time, fully charge it, power it off, and put it in a cool and dry place. The machine shall be charged at least once every three months to avoid damage to be the battery due to over-discharge.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

IC WARNING
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference; and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

FCC / IC Radiation Exposure Statement
This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20-cm between the radiator & your body.

WARNING

1. This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory, or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be done by children without supervision.
2. For the purposes of recharging the battery, only use the detachable supply unit provided with this appliance.
3. This appliance contains batteries that are only replaceable by skilled persons.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>