Thomann ROADWORX Keyboard Stand Z User Guide
- June 13, 2024
- Thomann
Table of Contents
Thomann ROADWORX Keyboard Stand Z
Product Information
The Keyboard Stand Z is a versatile and adjustable stand designed to securely hold keyboards and other similar equipment. It features a sturdy construction and various adjustment options to accommodate different heights and widths.
Key Features:
- Adjustable height range: 645 – 915 mm
- Adjustable width range: 630 – 930 mm
- Support arm catches with unlocking rings
- Maximum load capacity: 50 kg
- Cross brace with hand screws for secure fastening
- Environmentally friendly packaging materials
Product Usage Instructions
Safety Instructions:
- Risk of injury due to tipping of stand on an unsuitable ground! Place the stand only on flat and solid ground.
- Risk of injury due to tipping of the stand during loaded transport! Always remove equipment from the stand before moving it.
- Risk of injury due to tipping, excessive loading, and improper use! Never sit down on the product and never exceed the specified maximum load.
- Possible staining due to plasticizer in rubber feet! Use a suitable mat or felt slide to prevent direct contact between the device’s rubber feet and the floor.
- Avoid using liquid cleaners such as benzene, thinners, or flammable cleaning agents.
Setup & Adjustment:
- Unfold the upper and lower support arms of both side panels from the center support until they audibly click into place.
- Screw the cross brace with the provided screws and washers to both side panels.
- To adjust the height, loosen the hand screws on both side panels. Pull the supports out to achieve the desired total height and then tighten the screws again.
- To adjust the width, loosen the hand screw located on the cross brace. Pull the support out to achieve the desired overall width and then re-tighten the screw.
- To fold in the upper and lower support arms for transport, pull on the rings to unlock the catches for the support arms.
Packaging Disposal:
The packaging materials used for this product are environmentally friendly and
can be sent for normal recycling.
Please ensure that plastic bags, packaging, etc. are disposed of properly. Do
not dispose of these materials with your normal household waste, but make sure
they are collected for recycling.
Please follow the instructions and markings on the packaging.
Disposal Note:
For documentation disposal in France, please observe the disposal note provided.
Document ID: 522448_20.10.2023
Quick start guide
This document contains important information for the safe use of the product.
Read and follow the safety notes and all other instructions. Keep the document
for future reference. If you pass on the product, please also include this
document. The right to make changes is reserved. Please refer to the latest
version of the documentation, which is ready for download under
www.thomann.de.
Safety instructions
Intended use
This product is used as a secure keyboard stand. Any other use or use under
other operating conditions is considered to be improper and may result in
personal injury or property damage. No liability will be assumed for damage
resulting from improper use. This product may be used only by persons with
sufficient physical, sensory, and intellectual abilities and the necessary
knowledge and experience. Other persons may use this product only if they are
supervised or instructed by a person who is responsible for their safety.
Risk of injury and choking hazard for children!
Children can suffocate on packaging material and small parts. Children can
injure themselves when handling the product. Never allow children to play with
the packaging material and the product. Always store packaging material out of
the reach of babies and small children. Always dispose of packaging material
properly when it is not in use. Never allow children to use the product
without supervision. Keep small parts away from children and make sure that
the product does not shed any small parts that children could play with.
Risk of injury due to tipping of stand on an unsuitable ground!
If the stand is placed on soft or uneven ground, it may overturn and cause
injuries and property damage. Place the stand only on flat and solid ground.
Risk of injury due to tipping of the stand during loaded transport!
If the stand is moved without removing the loaded equipment, the stand may tip
over and cause injuries and property damage. Always remove equipment from the
stand before moving the stand.
Risk of injury due to tipping, excessive loading and improper use!
In case of excessive and uneven loading, the product might tip over, causing
injury and property damage. The product cannot hold people. Never sit down on
the product. Never exceed the specified maximum load for the product.
Possible staining due to plasticiser in rubber feet!! he plasticiser contained
in the rubber feet of this product may react with the coating of the floor and
cause permanent dark stains after some time.
If necessary, use a suitable mat or felt slide to prevent direct contact
between the device’s rubber feet and the floor
Where to use the product
Never use the product
- in direct sunlight
- in conditions of extreme temperature or humidity
- in extremely dusty or dirty areas
- at locations where the unit can become wet
General handling
- To prevent damage, never use force when operating the switches and controls.
- Never immerse the appliance in water. Just wipe it with a clean dry cloth. Do not use liquid cleaners such as benzene, thinners or flammable cleaning agents.
Features
- Stand for one keyboard
- Z shape
- Height adjustable in steps: 645 – 915 mm
- Width adjustable in steps: 630 – 930 mm
- Support depth: 455 mm
- Max. load capacity: 50 kg
- Transport dimensions (W × H × D): 740 mm × 200 mm × 620 mm
- Weight: 10 kg
Setup & Adjustment
- Left side panel
- Hand screw for height adjustment
- Washer
- Hand screws for fastening the cross brace
- Hand screw for width adjustment
- Right side panel
- Ring for unlocking the support arm catches
- Unfold the upper and lower support arms of both side panels from the centre support until both support arms audibly click into place.
- Screw the cross brace with the screws (4) and the washers (3) to both side panels.
- To adjust the height of the keyboard stand, loosen the screws (2) on both side panels. Pull the supports out of both side panels so that the desired total height is achieved. Then tighten the screws (2) again.
- To adjust the width of the keyboard stand, loosen the screw (5). Pull the support out of the cross brace so that the desired overall width is achieved. Then re-tighten the screw (5).
- To be able to fold in the upper and lower support arms for transport, first pull on the rings (7) to unlock the catches for the support arms.
Environmentally friendly materials have been chosen for the packaging. These materials can be sent for normal recycling. Ensure that plastic bags, packaging, etc. are disposed of in the proper manner. Do not dispose of these materials with your normal household waste, but make sure that they are collected for recycling. Please follow the instructions and markings on the packaging.
Observe the disposal note regarding documentation in France.
Thomann GmbH
Hans-Thomann-Straße 1
96138 Burgebrach
www.thomann.de
info@thomann.de
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>