IPercom 1717-21 IP Video Door Phone User Guide
- June 13, 2024
- IPercom
Table of Contents
10’’ MAX VIDEO DOOR PHONE
1717-21 IP Video Door Phone
Sch./Ref. 1717/21 max
INSTALLATION HANDBOOK
IMPORTANT The firmware version of the Ipercom system must be 2.1.0 or
higher for the operation of the device. The firmware version update of the
Ipercom system is available on the Unmet website in the Download/Software
section (registration required).
The video door phone Ref. 1717/21 is an IP video door phone dedicated to the
Ipercom system.
For trouble-free operation, the device requires a LAN/POE-type connection.
DESCRIPTION OF COMPONENTS AND CHARACTERISTICS
1. 10” touchscreen display
2. Webcam 2 Mpx
3. Microphone
4. Blue LED for alerts
5. HOME button
6. Micro SD card
7. Do not change the position of the switch| 8. LAN connector with POE power
supply (DOORPHONE POE PORT)
9. Secondary LAN connector for Internet Ipercom connection (LOCAL LAN PORT)
10. Printed circuit board with wire for connecting to the video door phone
for auxiliary functions
11. Speaker
12. 24 way connector for external connections’ printed circuit
---|---
Max video door phone is provided with an embedded device for hard of hearing.
DESCRIPTION OF THE TERMINALS ON THE PRINTED CIRCUIT FOR CONNECTING TO
THE SYSTEM
-
24-way connector for connecting the printed circuit board for external connections
-
External power supply terminals (+, -)
-
Terminals for the connection of:
• panic alarm (PANIC)
• floor call (FC)
• supplementary ringer (S+, S-)
• do not use terminals (-V, +V, -B, +B) -
Do not use terminals (G) and (L1 – L8)
INSTALLATION
It is possible to fix the wall bracket by using a 503 box or a box Ref.
1706/60 with supplied screws.
- Connect any panic function, extra ring tone, floor call, auxiliary power (if it is not connected to one POE port of the switched) system function wires to the terminals on the external printed circuit.
- Connect the video door phone to the connector J1 on the printed circuit board via the cable provided on the back of the video door phone.
- Place the wire in the locking slot.
- Move the video door phone close to the bracket by centering the special fixings 1 and slide it down to reach its stop 2 .
- Remove the protective film from the display.
WIRING INSTRUCTIONS
Cavo Ethernet RJ45
Ipercom system is developed for to work with the EIA/TIA 568B standard.
- Plug the cable into one of the RJ45 connectors with the Unmet logo.
- Insert the wire in its guide, according to the provided colour code (Standard T568B).
Wire No.| Cable colour
---|---
1| White-Orange
2| Orange
3| White-Green
4| Blue
5| White-Blue
6| Green
7| White-Brown
8| Brown - Cut the cables so that they protrude from the guide by about 5 mm, insert the guide in its plug and crimp with the specially provided tool.
- Make sure that the grey sheath stays inside the plug. This type of connection will NOT guarantee double insulation.
- Connect one end of the Ethernet cable to the POE switch of the system and the other end to the LAN connector of the device.
When using the local power supply, first connect the LAN cable to a non-POE port on the switch and then connect it to the local power supply.
4.1 POWER SUPPLY
The 1717/21 video door phone can be supplied power in two different ways:
— POE
— 48 V local power supply
When the power supply is used, POE is not available because the video door
phone is powered only by the local power supply. In this case, RJ45 can be
connected to the NO POE port of the switch.
4.2 DISTANCES AND CABLE SECTIONS
| Type of connection | Max distance | Min – max cross section |
|---|---|---|
| Call to floor level | 30 m | 0,5 – 1 mm² |
| Panic Alarm | 30 m | 0,5 – 1 mm² |
| Supplementary ringer | 30 m | 0,5 – 1 mm² |
| External power supply | 25 m | 0,5 – 1 mm² |
| LAN | 100 m | CAT5e (*) |
Wires with cross-section area of 0.5 mm² or larger must comply with IEC
60332-1-2; wires with cross section area smaller than 0.5 mm² must comply
with IEC 60332-2-2.
(*) To ensure longest-range video door phone operation, the cable must be a
class 5e device and the twisted pairs’ cross section must be AWG24.
The maximum resistance of the individual wires must not exceed 10ohm/100m.
The cable must be up to the following standards:
– EIA/TIA 568-B.2 or EIA/TIA 568-C.2
– EN50288 3-1
– IEC 61156-5
The connection between the video door phone and POE switch must be ensured by
a single cable without any extra patch cords.
DEVICE CONFIGURATION
Refer to the technical system manual by scanning the following QR Code with the camera of your smartphone or tablet to configure the device.
http://qrcode.urmet.com/default.aspx?arg=manuali&idProd=148051&sezione=Ipercom&lingua=en
TECHNICAL SPECIFICATIONS
POE input voltage: ……………………………………………………………………………….. 37-57 V
External power supply voltage: ……………………………………………………………….48 V – min. 15 W
Max consumption: …………………………………………………………………………………12 W
Display: ………………………………………………………………………………………………… 10” TFT
Touchscreen: …………………………………………………………………………………………. Capacitive
Brightness: …………………………………………………………………………………………….. 350 cd/m²
Resolution: …………………………………………………………………………………………….. 1024 x 600 px
Viewing Angle (H/V): ………………………………………………………………………………. 160° / 160°
Operating Temperature: …………………………………………………………………………….. ÷ 45°C
Max number of video door phones on the POE ports of switch 1039/44: ……….. 2
Dimensions (WxDxH): …………………………………………………………………………….288 x 186 x 29 mm
Frequency band:
WiFi: …………………………………………………………………………………………………….. 2400 ÷ 2483,5 MHz
Bluetooth ver. 4.0: …………………………………………………………………………………… 2402 ÷ 2480 MHz
Yokes: …………………………………………………………………………………………………….. 2400 ÷ 2480 MHz
Mifare: ……………………………………………………………………………………………………..13,56 MHz
Output power (Max):
WiFi: ……………………………………………………………………………………………………….. 20 dBm
Bluetooth ver. 4.0. ……………………………………………………………………………………… 4 dBm
Yokes: ……………………………………………………………………………………………………….. 10 dBm
Mifare: …………………………………………………………………………………………………………-4,7 dBμA/m @ 10m
This product is intended to be powered by either any external power supply units, through the connector J4 on the board CS1717-021 (15 W, 48 V ) or PoE, through the connector RJ45 (POE) whose power supply conforms to the limited power source (LPS) requirements and is protected against short circuits and power surges in accordance with the EN 62368-1:2014+A11 requirements.
KEY TO SYMBOLS
| Symbol | Description |
|---|---|
| Direct input voltage | |
| See the installation manual of the device |
SIMPLIFIED EU DECLARATION OF CONFORMITY
Hereby, URMET S.p.A. declares that the radio equipment type: 10” MAX VIDEO
DOOR PHONE Ref. 1717/21 is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the
following internet address: www.urmet.com
DIRECTIVE 2012/19/EU OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 4
July 2012 on waste electrical and electronic equipment (WEEE)
The symbol of the crossed-out wheeled bin on the product or on its packaging
indicates that this product must not be disposed of with your other household
waste.
Instead, it is your responsibility to dispose of your waste equipment by
handing it over to a designated collection point for the recycling of waste
electrical and electronic equipment.
The separate collection and recycling of your waste equipment at the time of
disposal will help to conserve natural resources and ensure that it is
recycled in a manner that protects human health and the environment.
For more information about where you can drop off your waste equipment for
recycling, please contact your local city office, your household waste
disposal service or the shop where you purchased the product.
DS1717-072A
URMET S.p.A.
10154 TORINO (ITALY)
VIA BOLOGNA 188/C
Telef. +39 011.24.00.000 (RIC. AUT.)
Fax +39 011.24.00.300 – 323
LBT20901
Area technical
Servizio client +39 011.23.39.810
http://www.urmet.com
e-mail: [email protected]
MADE IN CHINA
Documents / Resources
|
IPercom 1717-21 IP Video Door
Phone
[pdf] User Guide
1717-21 IP Video Door Phone, 1717-21, IP Video Door Phone, Video Door Phone,
Door Phone, Phone
---|---