CHAUVET Q6BT ILS Battery Operated Linear Wash Light User Manual

CHAUVET Q6BT ILS Battery Operated Linear Wash Light

Product Information

Before You Begin

• What Is Included
• Unpacking Instructions
• Claims
• Text Conventions
• Symbols
• Disclaimer
• Safety Notes
  • FCC Compliance
  • RF Exposure Warning for North America and Australia

Introduction

• Product Overview
• Product Dimensions

Setup

• AC Power
• Fuse Replacement
• Battery Power
• Power Linking
• Mounting
  • Orientation
  • Rigging

Operation

• Control Panel Operation
• Menu Map
• Configuration (DMX)
  • DMX Personality and Starting Address
• D-Fi USB Connectivity
  • D-Fi USB Compatibility
  • Configuration (D-Fi USB)

Before You Begin
Before using the EZLink Strip Q6BT ILS, please read the following:

• Check the contents of the package to ensure everything is included.
• Follow the instructions provided for unpacking the product.
• Take note of any claims mentioned in the manual.
• Familiarize yourself with the text conventions and symbols used in the manual.
• Read and understand the disclaimer.
• Pay attention to the safety notes provided.
  • For users in North America and Australia, be aware of RF exposure warnings.

Introduction
The EZLink Strip Q6BT ILS is a product that offers:

• A brief overview of its features and capabilities.
• The dimensions of the product.

Setup
To set up the EZLink Strip Q6BT ILS, follow these steps:

• Connect the product to AC power as instructed.
• If necessary, replace the fuse following the provided instructions.
• If battery power is desired, refer to the manual for battery installation.
• To achieve synchronized lighting effects, link multiple units together using the power linking feature.
• For mounting purposes, follow the instructions provided.
  • Ensure the correct orientation of the product.
  • Properly rig the product for secure installation.

Operation
To operate the EZLink Strip Q6BT ILS, follow these guidelines:

• Use the control panel to adjust and control various settings.

• Refer to the menu map for an overview of available options.

• Configure the product using DMX protocols as described in the manual.

  • Set the DMX personality and starting address according to your requirements.

• Utilize D-Fi USB connectivity for wireless control and synchronization.

  • Check the compatibility of the D-Fi USB with your system.
  • Configure D-Fi USB settings as necessary.

• What Is Included

• Unpacking Instructions

• Claims

• Text Conventions

• Symbols

• Disclaimer

• Safety Notes

  • FCC Compliance
  • RF Exposure Warning for North America and Australia

Introduction

• Product Overview
• Product Dimensions

Setup

• AC Power
• Fuse Replacement
• Battery Power
• Power Linking
• Mounting
  • Orientation
  • Rigging

Operation

• Control Panel Operation
• Menu Map
• Configuration (DMX)
  • DMX Personality and Starting Address
• D-Fi USB Connectivity
  • D-Fi USB Compatibility
  • Configuration (D-Fi USB)

Before You Begin
Before using the EZLink Strip Q6BT ILS, please read the following:

• Check the contents of the package to ensure everything is included.
• Follow the instructions provided for unpacking the product.
• Take note of any claims mentioned in the manual.
• Familiarize yourself with the text conventions and symbols used in the manual.
• Read and understand the disclaimer.
• Pay attention to the safety notes provided.
  • For users in North America and Australia, be aware of RF exposure warnings.

Introduction
The EZLink Strip Q6BT ILS is a product that offers:

• A brief overview of its features and capabilities.
• The dimensions of the product.

Setup
To set up the EZLink Strip Q6BT ILS, follow these steps:

• Connect the product to AC power as instructed.
• If necessary, replace the fuse following the provided instructions.
• If battery power is desired, refer to the manual for battery installation.
• To achieve synchronized lighting effects, link multiple units together using the power linking feature.
• For mounting purposes, follow the instructions provided.
  • Ensure the correct orientation of the product.
  • Properly rig the product for secure installation.

Operation
To operate the EZLink Strip Q6BT ILS, follow these guidelines:

• Use the control panel to adjust and control various settings.
• Refer to the menu map for an overview of available options.
• Configure the product using DMX protocols as described in the manual.
  • Set the DMX personality and starting address according to your requirements.
• Utilize D-Fi USB connectivity for wireless control and synchronization.
  • Check the compatibility of the D-Fi USB with your system.
  • Configure D-Fi USB settings as necessary.

What Is Included

• EZLink Strip Q6BT ILS
• Power cable
• Quick Reference Guide

Unpacking Instructions

Carefully unpack the product immediately and check the container to make sure all the parts are in the package and are in good condition.

Claims
If the box or the contents (the product and included accessories) appear damaged from shipping, or show signs of mishandling, notify the carrier immediately, not Chauvet. Failure to report damage to the carrier immediately may invalidate the claim. In addition, keep the box and contents for inspection.
For other issues, such as missing components or parts, damage not related to shipping, or concealed damage, file a claim with Chauvet within 7 days of delivery.

Text Conventions

Symbols

Disclaimer
Chauvet believes that the information contained in this manual is accurate in all respects. However, Chauvet assumes no responsibility and specifically disclaims any and all liability to any party for any loss, damage or disruption caused by any errors or omissions in this document, whether such errors or omissions result from negligence, accident or any other cause. Chauvet reserves the right to revise the content of this document without any obligation to notify any person or company of such revision, however, Chauvet has no obligation to make and does not commit to make any such revisions. Download the latest version from www.chauvetdj.com.
The works of authorship contained in this manual, including, but not limited to, all design, text, and images are owned by Chauvet.
© Copyright 2023 Chauvet & Sons, LLC. All rights reserved.
Electronically published by Chauvet in the United States of America.
CHAUVET, the Chauvet logo, and EZLink Strip Q6BT ILS are registered trademarks or trademarks of Chauvet & Sons LLC. (d/b/a Chauvet and Chauvet Lighting) in the United States and other countries. Other company and product names and logos referred to herein may be trademarks of their respective companies.

Safety Notes

ALWAYS:

• Connect to a grounded circuit.
• Connect to operating voltages as specified on the product’s spec sticker.
• Disconnect from power before replacing the fuse.
• Disconnect from its power source during periods of inactivity.
• Use a safety cable when suspending overhead.
• Heed all restrictions and warnings on the spec sticker.
• Mount in a location with at least 20 in (50 cm) of ventilation.
• Replace the fuse with the same type and rating.
• Use a clamp with a captive bolt when a single hanging bracket is used.

In the event of a serious operating problem, stop using it immediately.

DO NOT:

• Open this product or attempt any repairs. It contains no user-serviceable parts.
• Look at the light source when the product is on.
• Use if the power cord is crimped or damaged.
• Disconnect by pulling on the power cord.
• Allow flammable materials close to the product when it is operating.
• Touch the housing when it is on.
• Block any ventilation holes/slots in the housing.
• Connect to a dimmer or rheostat.
• Carry the product by its power cord.
• Operate in temperatures higher than 104°F (40°C).
• Expose to environments that exceed the Ingress Protection (IP) rating.
• Expose to rain or moisture.
• Use outdoors.
• Submerge.
• Leave outdoors for extended periods of time.
• Expose to corrosive environmental conditions such as temperature, humidity, salinity, pressure, radiation, or shock.
• Set this product on a flammable surface.

FCC Compliance

This device complies with Part 15 Part B of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
RF Exposure Warning for North America and Australia
Warning! This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter

• Keep this User Manual for future use. If the product is sold to someone else, be sure that they also receive this document.

**Introduction

**

Product Overview

Product Dimensions

Setup

AC Power
The EZLink Strip Q6BT ILS has an auto-ranging power supply, and it can work with an input voltage range of 100 to 240 VAC, 50/60 Hz. To determine the product’s power requirements (circuit breaker, power outlet, and wiring), use the current value listed on the label affixed to the product’s back panel, or refer to the product’s specifications chart. The listed current rating indicates the product’s average current draw under normal conditions.

• Always connect the product to a protected circuit (a circuit breaker or fuse). Make sure the product has an appropriate electrical ground to avoid the risk of electrocution or fire.
• To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely disconnect the product from power via breaker or by unplugging it.

NOTE
Never connect the product to a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer channel serves only as a 0 to 100% switch.

Fuse Replacement

1. Disconnect the product from power.
2. Wedge the tip of a flat-head screwdriver into the slot of the fuse holder.
3. Pry the safety cap out of the housing.
4. Remove the blown fuse from the clip on the front of the safety cap and replace it with a fuse of the exact same type and rating.
5. Re-insert the fuse holder and reconnect power.

Battery Power
The EZLink Strip Q6BT ILS comes with a rechargeable lithium battery for cable- free operation.

Charging the Battery
The battery charges whenever the EZLink Strip Q6BT ILS is plugged into a power source using the included power cord. If the product is plugged in and not in operation, make sure the product is turned off.

• The LED indicator light will flash if units are overcharged.
• DO NOT use the EZLink Strip Q6BT ILS on full power mode (all LEDs at 100%) while being charged/plugged into a power source, as the unit will get extremely hot.

Battery Life Indicator
The indicators on the LED Menu Display show how much battery life remains available. The drawing below provides a key to reading the battery life indicators.

Battery Run Time

Maximum Run Time (all colors on)| Maximum Run Time (single color on)| Recharge Time
---|---|---
Up to 8 hours| Up to 20 hours| 4 hours

Power Linking
The product provides power linking via the Edison outlet located in the back of the product. Please see the diagram below for further explanation.

Power-Linking Diagram

• NOTE It is possible to power link up to 33 EZLink Strip Q6BT ILS products on 120 VAC or up to 54 EZLink Strip Q6BT ILS products on 230 VAC.
• WARNING The power-linking diagram corresponds to the North American version of the product ONLY! If using the product in other markets, consult with the local Chauvet distributor, as power-linking connectors and requirements may differ by country or region.

Mounting

Before mounting the product, read and follow the safety recommendations indicated in the Safety Notes.

Orientation
The EZLink Strip Q6BT ILS may be mounted in any position; however, make sure adequate ventilation is provided around the product.
Rigging

• Before deciding on a location for the product, always make sure there is easy access to the product for maintenance and programming purposes.
• Make sure that the structure onto which the product is being mounted can support the product’s weight (see the Technical Specifications for weight specifications).
• When mounting the product overhead, always use a safety cable. Mount the product securely to a rigging point, whether an elevated platform or a truss.
• When rigging the product onto a truss, use a mounting clamp of appropriate weight capacity.
• When power-linking multiple products, mount the products close enough for power-linking cables to reach.
• The bracket adjustment knobs allow for directional adjustment when aiming the product to the desired angle. Only loosen or tighten the bracket knobs manually. Using tools could damage the knobs.

**Mounting Diagram Operation

**

Control Panel Operation
To access the control panel functions, use the four buttons located next to the display. Please refer to the Product Overview to see the button locations on the control panel.

value when in a function
< DOWN>| Navigates downwards through the menu list and decreases the numeric value when in a function
< ENTER>| Enables the currently displayed menu or sets the currently selected value into the selected function

Menu Map
Refer to the EZLink Strip Q6BT ILS product page on www.chauvetdj.com for the latest menu map.

DMX Mode

| 4Ch|

d 1–509

| 4-channel DMX mode
6Ch| 6-channel DMX mode
16Ch| 16-channel DMX mode
ILS Mode| iLS| iLS1–4| Sets ILS mode
Static Colors| C- –| C 1–15| Static colors
Automatic Programs| P- –| P 1–8| Automatic programs
Auto Speed| S- –| S. 1–100| Program speed for P 1–8
Dimmer| d- –| L. 1–255| Dimmer
Sound- Active Mode| Snd| Snd1–8| Sound-active programs
Sensitivity| SEnS| u 0–100| Sound sensitivity

Custom Color Mixing

|

u- –

| r. 0–255|

Custom static colors combine red, green, blue, and amber

G. 0–255
b. 0–255
A. 0–255
S. 0–100| Strobe rate
Bluetooth **Mode*| bLE| _**| Bluetooth control mode, displays Bluetooth ID

Control Mode

|

SEt

| ir| on| Turns infrared on or off
oFF
out| SLAV| Enable Master/Slave with other BT products
dMX| Enable Master/Slave with non-BT products

*The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Chauvet & Sons, LLC is under license. Other trademarks and trade names are those of their respective owners.

Configuration (DMX)
The EZLink Strip Q6BT ILS works with a DMX controller. Information about DMX is in the CHAUVET DMX Primer, which is available from the Chauvet website: www.chauvetdj.com.

DMX Personality and Starting Address
When selecting a starting DMX address, always consider the number of DMX channels the selected DMX mode uses. Choosing a starting address that is too high could restrict the access to some of the product’s channels. The EZLink Strip Q6BT ILS uses up to 16 DMX channels in a 16Ch DMX mode, which defines the highest configurable address to 497.
For more information about the DMX protocol, download the DMX Primer from: www.chauvetdj.com.

To select the starting address, do the following:

1. Press repeatedly until 4Ch, 6Ch or 16Ch shows on the display.
2. Press and d 1–509 will show on the display.
3. Use or to select the starting address. Press .

D-Fi USB Connectivity
The EZLink Strip Q6BT ILS is able to become a D-Fi wireless receiver/transmitter with the use of the D-Fi USB from Chauvet DJ. Simply set the product’s DMX Personality and DMX Address, set the DIP switch D-Fi receiving/transmitting channel, and then plug it into the D-Fi USB port.

• WARNING! DO NOT plug anything other than a D-Fi USB into the USB port. Doing so may cause damage to the product.

Once plugged in, the D-Fi USB will take over the product. Wired DMX and manual display control/menu buttons will be unavailable until the D-Fi USB is unplugged. The priority levels are:

1. D-Fi USB
2. Wired DMX
3. Manual Digital Display/Menu Buttons

D-Fi USB Compatibility
The D-Fi USB can receive a DMX signal from the D-Fi Hub and the FlareCON Air 2 as well as other D-Fi USB products.

Configuration (D-Fi USB)

1. Set the DMX Personality and DMX address on the EZLink Strip Q6BT ILS .
2. Use the Chart provided to set BOTH:
   • the Channel, and
   • the Receiving or Transmitting option

DIP Switch 5 is for Transmitting OR Receiving, please choose carefully.

D-Fi USB DIP Switch Channels

****

DMX Values

–

| ****

–

| ****

14

| ****

Auto programs

| 000 ó  005| No function
006 ó  036| Auto program 1 (programs 2–7)
037 ó  068| Auto program 2
069 ó  100| Auto program 3
101 ó  132| Auto program 4
133 ó  164| Auto program 5
165 ó  196| Auto program 6
197 ó  228| Auto program 7
229 ó  255| Auto program 8
–| –| 15| Auto speed| 000 ó  250| Program speed, slow to fast
251 ó  255| Sound-active mode
–| 5| 16| Dimmer| 000 ó  255| 0–100%

Configuration (Standalone)
Set the product in one of the standalone modes to control without a DMX controller.

NOTE
Never connect a product that is operating in any standalone mode to a DMX string connected to a DMX controller. Products in standalone mode may transmit DMX signals that could interfere with the DMX signals from the controller.

Preset Color Mode
To run the EZLink Strip Q6BT ILS on a static color, follow the instructions below:

1. Press repeatedly until C– shows on the display.
2. Press .
3. Use or to select a static color, from C 1–15.
4. Press .

Automatic Programs
To run the EZLink Strip Q6BT ILS in automatic mode, follow the instructions below:

1. Press repeatedly until P– shows on the display.
2. Press .
3. Use or to select an automatic program, from P 1–8.
4. Press .

Auto-Program Speed
To change the auto-program speed on the EZLink Strip Q6BT ILS, do the following:

1. Press repeatedly until S– shows on the display.
2. Use or to increase or decrease the program speed, from S. 1–100.
3. Press . The product will return to the last selected mode.

Dimmer
To set the dimmer curve, follow the instructions below:

1. Press repeatedly until d– shows on the display.
2. Press .
3. Use or to increase or decrease the dimmer, from L. 1–255.
4. Press .

Sound-Active Programs
To run the EZLink Strip Q6BT ILS with a sound-active program, follow the instructions below.

1. Press repeatedly until Snd shows on the display.
2. Use or to set the Sound-Active program, from Snd1 to Snd8.
3. Press .

Sound Sensitivity
To set the sound sensitivity on the EZLink Strip Q6BT ILS , do the following:

1. Press repeatedly until SEnS shows on the display.
2. Use or to increase or decrease the sound sensitivity, from u 0–100.
3. Press .

Custom Color Mixing
To custom mix a static color, do the following:

1. Press repeatedly until u– shows on the display.
2. Press and one of the following will show on display.
   •  r. _ (red)
   • G. _ (green)
   • b. _ (blue)
   • A. _ (amber)
   • S. _(Strobe)
3. Press to cycle through the color settings.
4. When the desired color shows on the display, use or to increase or decrease the color value, from 000–255 (red, green, blue, amber) or 000–100 (Strobe).
5. Repeat steps 3 and 4 until the product outputs as desired.

IRC-6 Infrared Remote Control
The EZLink Strip Q6BT ILS can be operated with the CHAUVET IRC-6. To enable IR wireless control, follow the instructions below.

1. Press repeatedly until SEt shows on the display.
2. Press .
3. Press repeatedly until ir shows on the display.
4. Press .
5. Press repeatedly until ON shows on the display

IRC-6 Operation

Bluetooth Control
Bluetooth control mode allows users to control one or more EZLink Strip Q6BT ILS products via Bluetooth connection on the BTAir app.
To operate the product via Bluetooth control mode:

1. Press repeatedly until bLE shows on the display.
2. Press .
3.  Use the ID number on the display to identify the product on the BTAir app.

Automatic Mode
To turn on Automatic mode with the IRC-6:

1. Press on the IRC-6.
2. Press <+> or <–> to change program.

Sound-Active Mode
To turn on Sound-Active mode with the IRC-6:

1.  Press on the IRC-6.
2. Press <+> or <–> to increase or decrease the sensitivity.

To adjust the sound sensitivity:

1.  Press on the IRC-6.
2. Press <+> or <–> to increase or decrease the sensitivity.

Strobe
To turn on Strobe mode with the IRC-6:

1. Press on the IRC-6.
2. Press <+> or <–> to increase or decrease the strobe speed.

Manual Control
To manually select the laser color with the IRC-6:

1. Press the desired color, from (red), (green), (blue), or (amber).