CONDUCTIX Wampfler FB-606 Infrared Manual Remote Control Instruction Manual
- June 13, 2024
- Conductix Wampfler
Table of Contents
Instruction manual
FB-606
Infrared Manual Remote Control BDA_0002_FB-606_en
www.conductix.com
Item number| WNR|
---|---|---
3226565| CWA-60060830| FB-606
3224334| CWA-60608103| FB-606 TF
General information and safety
1.1 Information about the manual
This manual contains technical information and operating notes about devices
of the type:
FB-606 Infrared Manual Remote Control
FB-606 TF Infrared Manual Remote Control tropicalized
It gives important information about the device.
Please read this manual carefully before using the device!
It will ensure smooth operation and prevention of errors, defects and damage
to the system. Moreover, universal safety and accident prevention
specifications must be implemented at sites where the devices are in use.
The manual includes important instructions regarding the operation and safety;
it is a part of the product and must readily available, close to the device,
so that it is accessible to the personnel at all times. Every person who is
assigned to work on or with the device must have read and understood this
manual before working with the device. This is mandatory even if the concerned
person has already worked with such a device or the like, or has been trained
by the manufacturer.
1.2 Symbols in the documentation
There are warning instructions and symbols in this description. It is absolutely mandatory to comply with these and follow them. These are working aids and they will warn you of possible damage to property and personnel. Always follow these instructions. Moreover, always follow the universal safety specifications and accident prevention specifications.
| Warning! This symbol along with the signal word “Warning” refers to a
potentially dangerous situation that can lead to serious injuries or fatality
if it is not avoided.
---|---
| Caution! This symbol along with the signal word “Caution” refers to a
potentially dangerous situation that can lead to minor injuries and damage to
property if it is not avoided.
| Note!
This symbol indicates that there are additional and important information and
tips on the relevant topic.
| See also!
This symbol indicates that other detailed descriptions on the particular topic
are available or provides references to other sections in this documentation.
1.3 Limitation of liability
All data and instructions in this description have been compiled taking into consideration the applicable standards and specifications, the state-of-the- art technology and our knowledge and experience gained over the years. Conductix-Wampfler Automation GmbH is not liable for any damage or operational disorders arising due to:
- Non-compliance with the description
- Improper use
- Employment of untrained personnel
- Independent remodelling and modification of the device
Moreover, non-compliance with the description absolves Conductix-Wampfler Automation GmbH of the warranty obligation.
1.4 Copyright
The contents of this description should be treated as confidential. It is
meant solely for persons working with the device. Handing over this technical
document to third parties without written permission of the manufacturer is
not allowed.
Note!
The content details, texts, drawings, images and other illustrations of the
description are protected by copyright and are subject to the industrial
property rights. Any improper utilization is punishable by law.
1.5 Conformity
Devices made by Conductix-Wampfler Automation GmbH been designed to comply
with EU directives.
Please contact Conductix-Wampfler Automation GmbH if you wish to obtain a copy
of these EU declarations of conformity.
1.6 Proper use
The infrared manual remote control FB-606 is only used to manually control
Conductix/LJU controllers that have the accompanying software and are fitted
with a infrared interface.
Warning! Danger due to improper use! Any improper use and/or different use of the device can lead to dangerous situations.
Therefore:
- Only use the device in a proper manner.
- Under all circumstances, comply with all technical data and permissible conditions at the site of operation.
- Do not deploy the device in areas with explosion hazard and in environments with hazardous oils, acids, gases, vapors, dust, radiation, etc.
1.7 Spare parts and repair
Warning!
Risk of injury due to spurious spare parts and incorrect repair!
Spurious or faulty spare parts and repair can lead to damage, malfunctions or
total failure and can impair safety.
Therefore:
- Use only original spare parts of the manufacturer.
- Replace defective devices immediately and send them in for repair.
When ordering a spare part, specify the plant number WNR of the component and send it to the address given on the inner side of the covering sheet (page 2). The plant number is given on the type plate of the individual components. (see figure) Send in the defective device for repair with a short description of the error scenario to the address given on the inner side of the covering sheet (page 2).
1.8 Warranty
The warranty covers only manufacturing defects and component defects.
The manufacturer is in no way responsible for damage during transit or
unpacking.
In no case and under no circumstances shall the manufacturer be liable under
warranty for defects or damage caused by improper use, incorrect installation
or impermissible operating conditions, or due to dust or aggressive
substances.
Consequential and accidental damage are excluded from the warranty.
The warranty is valid for 12 months from the commencement of operation,
however, maximum 24 months after delivery.
Resellers or distributors may negotiate different warranty periods in
accordance with their terms and conditions of sale and delivery.
If you have further questions relating to the warranty, please contact your
supplier.
1.9 Customer service
Our customer service is available to provide technical information.
Information about the responsible contact persons can be obtained via
telephone, fax, e-mail or the Internet; see contacts on the inner side of the
covering sheet (page 2).
1.10 Modifications and alterations
To avoid danger and to ensure optimal performance, no modifications,
remodelling or add-ons are allowed on the device unless expressly approved by
Conductix-Wampfler Automation GmbH.
Warning!
Risk of injury due to design modification!
Unauthorized technical modifications can lead to considerable damage to
persons and property.
Therefore:
- Replace the defective device!
- Replace it with a device of the same model.
1.11 Personnel and qualification
Warning!
Risk due to improper use!
Improper operation can lead to serious damage to persons or property.
Therefore:
- It may be operated only by qualified technical personnel.
- During manual operation, ensure that there is no risk to persons from the manual operation and that there are no persons in the working area of the vehicle.
1.12 Disposal instructions / environmental specifications
Provided no agreement for take-back or disposal has been made, the individual
components of the device must be appropriately dismantled, segregated and
disposed of or recycled according to the current stipulations.
Materials marked with the recycling symbol or green dot have to be disposed of using the appropriate recycling method.
1.13 Battery disposal
The device contains batteries.
Dispose of them according to applicable provisions:
- Do not dispose of batteries as domestic waste.
- Dispose of batteries at local collection points or have a professional company dispose of them.
- Do not short circuit batteries.
- Tape battery contacts.
Characteristics and design
2.1 Characteristics
The infrared manual remote control FB-606 is used to manually control and
remote control controllers that have the accompanying software and are fitted
with a infrared interface.
The FB-606 supports two IR transmission speeds. Therefore it is compatible
with vehicle controllers of the 5xx, 6xx and 7xx series as well as vehicle
controllers of the latest generation 8xx.
The remote control permits the switching of controllers to manual mode (hand
mode) so that e.g. a vehicle can be moved manually using various commands.
Thus, commands such as “Travel forwards/backwards” and “Hoist/Lower” can be
given by pressing the relevant buttons.
It is also possible to acknowledge errors using the manual remote control.
The various commands are transmitted to the controller using coded IR signals.
These signals are controller-dependent.
Functions!
The functions of the manual remote control are specific to projects.
The assignment of buttons to your controller is given in the separate
descriptions to your controller.
2.2 Design
- The housing of the infrared remote control FB-606 is made of impact-resistant plastic.
- The Keypad with 6 buttons on the remote control is simply to use and protected, which helps prevent the buttons from being accidentally pressed.
- The status of the remote control is monitored with a control LED.
- IR transmit diodes for infrared transmission are located at the front of the device.
- Die Power is supplied by a 9V block battery. The battery can be changed in the battery compartment on the underside of the device.
Operation of the FB-606
Warning!
Risk due to improper use!
Improper operation can lead to serious damage to persons or property.
During manual operation, ensure that there is no risk to persons from the
manual operation and that there are no persons in the working area of the
vehicle.
3.1 Functioning
The 6 operating buttons on the remote control are used to remote control
controllers and to acknowledge errors.
The commands are transmitted via infrared. The control LED of the remote
control is blinking when a command is sent!
For remote control or acknowledge errors, the IR transmit cone must be
directed with a tolerance of +/- 20° towards the display window of the
controller.
The range of the remote control to the receiver is at least 6 m.
3.2 Switching On/Off
The infrared manual remote control FB-606 has no switch ON/OFF.
Using a button on the remote control, commands are sent immediately.
The buttons on the remote control are recessed, which helps prevent the
buttons from being accidentally pressed.
3.3 Selection of the transmission speed
The infrared manual remote control FB-606 supports two infrared transmission speeds.
Mode | Description |
---|---|
Fast infrared | Control-LED is blinking fast Transmission rate 62500 bit/s e.g. |
for controllers of the 6xx, 7xx and 8xx series
Slow infrared| Control-LED is blinking slow Transmission rate 9600 bit/s e.g.
for controllers of the 5xx series
Select the transmission speed by pressing a hot key. The currently active mode is shown with the control LED.
-
Change “Slow infrared“:
Press the buttons , and simultaneously for 5 sec. until the control LED on the remote control is blinking slow. -
Change “Fast infrared“: Press the buttons , and simultaneously for 5 sec. until the control LED on the remote control is blinking fast.
3.4 Remote control
Devices with Conductix/LJU controllers can be operated remotely via the
infrared interface in the controller display using the remote control. That
means functions like driving can be manually controlled using them.
To switch the controller in manual mode (hand mode) press the button of the
remote control. If the controller is in a manual operating mode, this is
displayed by a flashing “H” in the controller display.
Button assignment!
The functions of the buttons are specific to projects.
An example is shown in the following table.
The assignment of buttons to your controller is given in the separate
descriptions to your controller.
Example button assignment:
**Button *** | Function |
---|---|
Switching to manual mode resp. error reset | |
# | Normal mode (automatic mode) |
Travel forward slow | |
Travel forward fast | |
Travel backward slow | |
Travel backward fast | |
Hoisting slow | |
Hoisting fast | |
Lowering slow | |
Lowering fast |
- two buttons: press the buttons simultaneously
Note!
Special function -button!
Normally commands are buffered by the controller software.
Release all buttons and press the -button immediately, the last command is
breaking (clear buffer memory) and the movement will be stopped immediately.
3.5 Acknowledge errors
By switching the controller in manual mode “H“ and back to automatic mode
errors can be acknowledged.
Only acknowledge rrors after troubleshooting.
Technical information
4.1 Data sheet
General
Type| FB- 606| FB-606 TF
Item number| 3226565| 3224334
WNR| CWA-60060830| CWA-60608103
Housing| impact-resistant plastic
Colour| black
Dimensions H x W x D| 147 mm x 68 mm x 27 mm
Weight| 120 g
IP protection class| IP 30
Status| 1 x LED red
Number of operation buttons| 6
Electrical data
Power supply| 9 V block battery
Average power consumption transmit| approx. 70 mA
Standby| approx. 2 μA
Data transmission
Principle of operation| Control signal transmission with infrared radiation
(identical to the principle of remote control of a television)
Transmission rate| slow infrared: 9600 bit/s fast infrared: 62500 bit/s
Modulation type 1 (slow infrared)| Transmission frequency 125 kHz,
bit-coded frequency sampling at 9600 bit/s
Modulation type 2 (fast infrared)| IrDA (worldwide standard of the “Infrared Data Association”), bit-coded infrared single pulses
with a pulse width of 1 μs at 62500 bit /s
Wavelength| 850 nm
Radiant power| 240 mW
Range| at least 6 m, typical 10 m
Angle of reflected beam| ± 20°
Ambient conditions
Operating temperature| + 10 °C to + 50 °C
Storage temperature| – 10 °C to + 50 °C
Relative humidity| < 80% non-condensing
tropicalized| –|
4.2 Device drawing
BDA_0002_FB-606_en
www.conductix.com
Conductix-Wampfler Automation GmbH
Handelshof 16 A
14478 Potsdam
Germany
Phone: +49 (0) 331 887344-0
Fax: +49 (0) 331 887344-19
E-mail: info.potsdam@conductix.com
Internet: www.conductix.com
Translation of the original document
March 2022
The standard names, trade names, product names etc. used in this description
may also be brand names even when not specially indicated and, as such, are
subject to the statutory stipulations.
© 2022 Conductix-Wampfler Automation GmbH
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>