Whirlpool LIB0158558D Wall Hood Instruction Manual

Whirlpool LIB0158558D Wall Hood

GENERAL SAFETY

• Do not make electrical or mechanical changes on the product or on the exhaust pipes.

• Before doing any cleaning or maintenance work, disconnect the product from the mains power supply by removing the plug or turning off the mains switch.

• For all installation and maintenance operations, always wear work gloves.

• The product can be used by children over the age of 8 and by people with reduced physical, sensory or mental capabilities or without experience or the necessary knowledge, as long as they are properly supervised or have been instructed on how to safely use the device and understand the inherent dangers.

• Children must be supervised to make sure that they do not play with the product.

• Cleaning and maintenance must never be performed by children unless they are properly supervised.

• The room must have sufficient ventilation when the product is used at the same time as other appliances burning gas or other fuels.

• The product must be cleaned frequently both inside and out (AT LEAST ONCE A MONTH); always follow the instructions given in the maintenance manual.

• Failure to comply with the rules indicated for cleaning the product and replacing/cleaning the filters may result in the risk of fire.

• It is strictly forbidden to cook food on the flame under the product.

• WARNING: When the hob is on, the accessible parts of the product may become hot.

• Do not connect the product to the electrical power supply until the installation is complete.

• The regulations laid down by local authorities must be strictly followed with regard to the technical and safety measures to adopt for fume extraction.

• The extracted air must not be conveyed through the same ducts used to extract the fumes generated by gas combustion or other types of combustion products.

• Do not use or leave the product without appropriately installed lamps, as this may result in the risk of electric shock.

• The product must NEVER be used without the grille correctly fitted.

• The product must NEVER be used as a support surface unless expressly indicated.

• Range hoods and other cooking fume extractors may adversely affect the safe operation of appliances burning gas or other fuels (including those in other rooms) due to backflow of combustion gases. These gases can potentially result in carbon monoxide poisoning. After installation of a range hood or other cooking fume extractor, the operation of flued gas appliances should be tested by a competent person to ensure that backflow of combustion gases does not occur.

• Use only the fastening screws supplied with the product for its installation, or if not supplied, purchase the correct type of screws. Use screws of the right length, as indicated in the installation guide.

• Please note! Failure to install screws and fasteners in accordance with these instructions may result in electrical hazards.

• To replace the lamp, only use the lamp indicated in the maintenance/lighting system section of this manual.

• Using a naked flame may damage the filters and cause a fire hazard, and must therefore be avoided under all circumstances.

• Extra care must be taken when frying to prevent the oil from overheating and catching fire.

• In case of doubt, contact the authorized service center or similar qualified personnel.
  Please note! Do not use a programmer, timer, separate remote control or any other device that activates automatically.

• The minimum distance between the container support surface on the cooker and the lower part of the hood must be at least equal to 50 cm (not less than 65 cm only for Australia and New Zealand) in case of electric cookers and to 65 cm in case of gas or mixed cookers.

• If the installation instructions of the gas cooker specify a greater distance, take it into account.

• Keep children under the age of 3 away from the appliance. Without the constant supervision of an adult, keep the appliance out of the reach of children under the age of 8.

• ATTENTION: the appliance is not designed to be operated using an external device or a separate remote control system.

• This appliance is not intended for professional use. Do not use the appliance outdoors.

• To avoid the risk of personal injury, the appliance must be handled and installed by two or more people.

• Installation operations, including any water supply connections (if any) and the electrical connections, and repairs must be carried out by qualified personnel. When installation is complete, keep the packaging material (plastic parts, polystyrene, etc.) out of the reach of children to avoid the risk of suffocation.

• Do not use the appliance when barefoot or wet.

• Never use steam cleaning appliances – risk of electric shock.

• The packaging material is 100% recyclable and is marked by the recycling symbol

• The device may have different aesthetic features with respect to the illustrations in this handbook, however, the operating, maintenance and installation instructions remain the same.

Strictly observe the instructions in this manual. All liability is declined for any problems, damage or fires caused by failure to comply with the instructions in this manual. The device is intended for domestic use only, to cook food and extract the fumes generated by cooking. No other use is allowed (e.g. heating rooms). The manufacturer declines any liability for inappropriate use or incorrect control settings.

• Read the instructions carefully: they contain important information on installation, operation and safety.
• Do not make electrical changes to the device.
• Before installing the device, make sure that none of the components are damaged. Otherwise, contact the dealer and do not continue with the installation.
• It is important to keep all the manuals accompanying the product so that they can be consulted at all times. If sold, transferred or moved, make sure it remains with the product.

WHAT’S INCLUDE

ELECTRICAL CONNECTION

The mains voltage must correspond to the voltage indicated on the rating plate located inside the hood. If equipped with a plug, connect the hood to a wall socket that complies with current standards located in an area that can be accessed even after installation. If it does not feature a plug (direct connection to the mains) or the plug is not located in an accessible area, even after installation, apply a standard double pole switch that ensures complete disconnection from the mains in category III overvoltage conditions, in accordance with the installation rules.

• Please note! Before reconnecting the circuit to the mains power supply, make sure that it is working correctly, always check that the power cable is correctly installed.
• Do not use extension cords, power strips or adapters.

Mains voltage and frequency
Refer to the value indicated on the rating plate inside the hood.

Wire connection

• : yellow/green
• N: blue
• L: brown

Replacing the power cable
The hood features a special power cable; if the cable is damaged, contact the Service Centre for a replacement.

AIR OUTLET

(for suction versions)
Connect the hood to wall-mounted exhaust pipes and holes with a diameter equivalent to the air outlet (connecting flange). The use of pipes and outlet holes in the wall with a smaller diameter will reduce the extraction performance and drastically increase the noise level.
All responsibility in this regard is therefore denied.

• Use a ducting pipe with the shortest length necessary.
• Use a ducting pipe with the least number of bends possible (maximum bend angle: 90°).
• Avoid drastic changes in the ducting pipe diameter.
• The company shall not be held responsible if these regulations are not complied with.

FILTRATION OR SUCTION?
Your hood is read to be used in the suction version. To use the hood in the filtration version, the special ACCESSORY KIT must be installed. Check, on the first pages of this manual, whether the ACCESSORY KIT is already supplied or needs to be purchased separately.

Note: If supplied, in some cases, the additional activated carbon filtering system may already be installed on the hood. Information on how to convert the hood from the suction version to the filtration version is already contained in this manual. Extraction version
Vapors are evacuated outside through an exhaust pipe attached to the connecting flange.

ATTENTION

• The evacuation pipe is not supplied and must be purchased.
• The diameter of the exhaust pipe must be equivalent to the diameter of the connecting ring.
• If the hood features one or more carbon filters, they must be removed.

Filtration version
The suctioned air will be degreased and deodorized before it is sent back into the room. To use the hood in this version, it is necessary to install an additional activated carbon filter system.

CONTROLS

The hood is equipped with a control panel with a suction speed control and a light control to light up the hob.

1. “Night Light” ON/OFF
2. Hob lights ON/OFF – Colour temperature selection
3. “Autolight” operation
4. “ZEN Mode” operation
5. Motor ON/OFF
6. “POWER BOOST 1” operation
7. “POWER BOOST 2” operation
8. “COOKSENSE” automatic operation
9. Filter saturation indicator
10. “Breath Daily Cycle” operating mode ON/OFF
11. “Breath Intensive Cycle” operating mode ON/OFF
12. WI-FI function active light indicator
13. WI-FI connection

“NIGHT LIGHT” ON/OFF
Press to switch the soft ambient lighting on/off.

HOB LIGHTS ON/OFF – COLOUR TEMPERATURE SELECTION
Press to switch the hob lighting on/off

• With the lights on, touch the SL1 LED strip with your fingers to the right or left respectively to increase or decrease the light intensity. Press again (long press) to set the lighting colour temperature.
• Touch the SL1 LED strip with your fingers to the right or left to set a colder or warmer light colour. If there are no colour changes for 5 seconds, SL1 flashes at the set colour level and a beep indicates that the system has saved the configuration.
  Note: the light switches to the last set colour before switch-off.

“AUTOLIGHT” OPERATION
Press to activate/deactivate the “Autolight” automatic lighting function.
Note: The function is activated only when the extraction hood is connected to the hob via Wi-Fi. Once the function is activated, the hob light will be controlled automatically depending on the status of the connected hob.

“ZEN MODE” OPERATION
Press to activate/deactivate “ZEN” extraction mode.
This function activates an extraction speed that is the best compromise between silence and extraction efficiency.

MOTOR ON/OFF
Press to switch the extraction motor on/off.

• With the motor on, touch the SL2 LED strip with your fingers to the right or left respectively to increase or decrease the extraction speed (power).

“POWER BOOST 1” OPERATION
With the extraction motor on, press T6 to activate the intensive extraction speed (power) “POWER BOOST 1” (timed). Note: After 5 minutes the extraction hood will continue to operate at the previously set speed

“POWER BOOST 2” OPERATION
With the extraction motor on, press T7 to activate the intensive extraction speed (power) “POWER BOOST 2” (timed). Note: After 5 minutes the extraction hood will continue to operate at the previously set speed.

“COOKSENSE” AUTOMATIC OPERATION
The hood automatically sets extraction speed (power) 1 and then increases it if the environmental conditions detected by the hood sensor require it. If there is no change in the environmental conditions, after 5 minutes (if the hood is already at extraction speed (power) 1), the hood switches off.

Note: for the correct use of this function, adjust the relative parameters first (see the paragraph “Adjusting the parameters for automatic operation”).
Note: during automatic operation, if the user uses other functions that adjust the speed, the auto ventilation function is deactivated.

FILTER SATURATION INDICATOR
At regular intervals, the hood signals the need to perform maintenance on the filters.
Note: the indicators are activated when the hood is on.

• Key T9 on: the grease filter requires maintenance.
• Key T9 flashing: the activated carbon filter requires maintenance.

Reset filter saturation indicator:
Note: this operation must be performed with the hood on.
Press and hold T9; the light goes out, indicating that the reset was successful.
Activation of the activated carbon filter saturation indicator.
Note: this operation must be performed with the extraction motor off.
This indicator is normally deactivated; it must be activated if the hood is installed in the filter version, i.e. in the presence of activated carbon filters. Simultaneously press and hold keys T1 and T10 to activate the function: the keys will light up, indicating activation. To deactivate the function, press and hold the same keys (T1 and T10) again: the keys will flash briefly, then go out, indicating deactivation.

“BREATH DAILY CYCLE” OPERATING MODE ON/OFF
The hood automatically sets extraction speed (power) 1 and then increases it if the environmental conditions detected by the hood sensor require it. If the extraction speed is not changed, depending on the environmental conditions detected, the hood switches off after 2 hours. In any case, after 5 hours the hood is switched off forcefully.
Note: for the correct use of this function, adjust the relative parameters first (see the paragraph “Adjusting the parameters for automatic operation).

“BREATH INTENSIVE CYCLE“ OPERATING MODE ON/OFF
The hood automatically sets the extraction speed (power) 5 and then increases it if the environmental conditions detected by the hood sensor require it. If the extraction speed is not changed, depending on the environmental conditions detected, the hood switches off after 2 hours. In any case, after 5 hours the hood is switched off forcefully.
Note: for the correct use of this function, adjust the relative parameters first (see the paragraph “Adjusting the parameters for automatic operation”).

WI-FI FUNCTION ACTIVE LIGHT INDICATOR
The indicator lights up when the hood is controlled remotely via App.

WI-FI CONNECTION
Press to activate/deactivate the Wi-Fi functions. This function allows the product to be connected to the Internet and remotely monitor/control the hood via a Smartphone or Tablet.
To use the Wi-Fi function, the device must be connected to the home wireless network (internet) according to the configuration procedure described in the “WI-FI MANUAL” instructions.

ADJUSTING THE PARAMETERS FOR AUTOMATIC OPERATION
For the correct use of automatic operation, perform “Hood calibration” and “Hob selection”.

Hood calibration
Note: this operation must be performed in standby mode, i.e. 1 minute after the motor has been switched off Press key T4 for 5 seconds. Extraction speed (power) 1 starts and key T4 flashes, indicating that hood calibration has started and will last for about 5 minutes.
Note: to interrupt calibration, press T4 for 5 seconds; the calibration will be invalidated and must be repeated.
Note: when the product is powered up for the first time, calibration is performed automatically: T4 flashing; wait 5 minutes for calibration to end.

Hob selection
Note: this operation must be performed in standby mode, i.e. 1 minute after the motor has been switched off Press key T10+T11 for 5 seconds. Keys T10 and T11 light up.
Press key T10 in the case of a gas hob – the key flashes, indicating successful selection. Press key T11 in the case of an electric hob – the key flashes, indicating successful selection. The pressed key will flash for 3 seconds, indicating that the selection has been saved.

INSTRUCTIONS FOR WI-FI CONNECTION

REMOTE CONTROL/“Whirlpool 6th Sense Live” APP CONFIGURATION PROCEDURE
The Whirlpool 6th Sense Live App allows you to operate and control the appliance remotely using an external device. To enable the appliance for remote control, it is necessary to perform the connectivity configuration procedure. This procedure is necessary to register the appliance and connect it to the home network. The configuration procedure only needs to be performed once. It will be necessary to perform it again only if the router properties change (network name, password or data provider).

BEFORE STARTING THE CONFIGURATION PROCEDURE

1. To perform the procedure, you will need: A Smartphone or Tablet with Android 7.0 (or higher) operating system, or an Ipad or IPhone with IOS 11 (or higher) operating system; • a Wi-Fi router b/g/n 2.4 Ghz connected to the Internet (check with your Smartphone or Tablet that the signal strength of your home wireless network is good in the place where the appliance is installed).
2. Download and install the free Whirlpool 6th Sense Live App on your Android Smartphone or Tablet or on your iPAD/iPhone from the online store. The App will provide all the necessary instructions for the installation procedure. If you do not have an account yet, create one and register for the service (by signing up to the legal terms) in order to be able to use all the features available in the App.
3. Register your appliance by following the instructions provided by the App. For the registration procedure, the SAID (Smart Appliance IDentifier) code, indicated on the appliance’s label, will be required. The SAID code is a combination of numbers and letters (10 characters). Write down the SAID code of your appliance here:

SAID ……………………………………..

BEFORE STARTING THE CONFIGURATION PROCEDURE

• Before starting the installation, switch on the router and check that the wireless signal from your home network reaches the appliance. To check the strength of the Wi-Fi signal, use a Tablet or Smartphone connected only to the Wi-Fi router, disable all other connections and bring the device near the appliance. Open any Internet page in a browser and check that it loads quickly and correctly. If the home Internet connection works properly but the page does not load, it may be necessary to install a Wi extension device (not included with the appliance).

• If the router supports WPS 2.0 (or later versions), follow the automatic configuration procedure to connect the appliances to the router. If the router does not support WPS, follow the manual configuration procedure. Follow the instructions of the Whirlpool 6th Sense Live App, which appear on your Tablet or Smartphone, to connect the appliance to your Wi-Fi network. Or, perform one of the automatic or manual connection procedures described in the following paragraphs.

  • INSTRUCTIONS FOR AUTOMATIC CONFIGURATION (FIRST USE)– WPS METHOD
    This procedure can be used only if the router supports WPS 2.0 (or later versions).
  1. On the appliance, activate the recognition process by pressing the connectivity key for three seconds (a beep will confirm the activation). The appliance is set to “search” mode and will search for a local network. The connectivity icon on the appliance will start flashing rapidly.
  2. On the wireless router, press the WPS key to establish a connection between the two products. A light on the router will start flashing.
  3. When the appliance connects to the local router, the Wi-Fi icon starts flashing more slowly (this feature is not supported on all devices).
  4. The device will try to connect to the backend system. The connectivity icon remains continuously lit. If the Wi-Fi icon doesn’t stop flashing after a few minutes, this means the device was not able to make a connection with the home network through WPS. Try repeating the procedure, and if it is unsuccessful, use the manual configuration procedure.
  5. The connection procedure to the Wi-Fi network can be interrupted by pressing the connectivity key.

DEACTIVATION / ACTIVATION OF WI-FI CONNECTIVITY
To deactivate the connection of the appliance to the Wi-Fi network, press the connectivity key for 5 seconds (a beep will confirm the deactivation). The Wi- Fi icon on the display of the appliance should turn off. To reactivate the Wi- Fi connection of the appliance, press the Wi-Fi key on the product. Once the connection has been configured, it can be deactivated and the appliance can be disconnected from the Wi-Fi network by pressing the connectivity key for 10 seconds (two beeps will confirm the deactivation, the first one after 5 seconds and the second one after 10 seconds). The Wi-Fi icon on the display of the appliance should turn off. To reconnect the appliance to the home Wi-Fi network, follow the procedure described in the “Preparing for Configuration” section.

INSTRUCTIONS FOR MANUAL CONFIGURATION (FIRST USE) – MICRO ACCESS POINT METHOD
This procedure uses Micro Access Point technology and can be used with routers that do not support WPS.

1. Before starting the configuration procedure, note the name (SSID) and password of the home wireless network and the SAID code of the device. This information will be needed during the installation procedure.

2. Turn the router on, check that the internet connection is active and connect your smartphone/tablet to your Wi-Fi network.

3. On the device, activate the recognition process by pressing the connectivity key for 5 seconds (two acoustic signals will be emitted as confirmation, the first after 3 seconds, the second after 5 seconds) • the Wi-Fi network icon should start flashing on the device’s interface.

4. Scan the QR code on the label affixed to the appliance; at this point, the Whirlpool 6th Sense Live App will provide detailed instructions to perform the procedure.
   Note: In some cases, the App may ask you to specify the type of appliance: in this case, select Hood.

5. Once the connection has been made, the Wi-Fi icon on the device should stop flashing and remain continuously lit. If not, disconnect and then reconnect the device to the mains power and repeat the procedure.

6. The configuration procedure is complete.

REMOTE CONTROL / DAILY USE
This function is only implemented on certain types of appliance.

1. Make sure that the router is switched on and connected to the Internet.
2. Make sure that the Wi-Fi connection status light on the product’s display is lit steadily.
3. The Whirlpool 6th Sense Live App allows for the appliance to be controlled remotely; in particular, it makes it possible to:
   • control the appliance and activate various options even when you are not at home;
   • access additional functions, such as Smart Energy mode;
   • optimise energy consumption, for example by taking advantage of the most convenient time slots;
   • access further information on the use of the appliance;
   • check the status of the appliance and any maintenance requirements (e.g. filter change);
   • Synchronize the hood with the compatible pyrolytic oven and hob, allowing the appliance to switch on fully automatically.

QUICK IDENTIFICATION OF THE APPLIANCE’S CONNECTION STATUS
If the Wi-Fi connection status light on the appliance’s display flashes quickly, it means that the appliance is trying to connect to the router. If, on the other hand, it flashes slowly, it means that the appliance is connected to the router but is not able to connect to the Internet (e.g. because the ADSL network is not working); some types of appliances do not support flashing at different speeds. If the light is lit steadily, it means that the appliance is connected to the Internet and to the Whirlpool cloud system.

INSTALLATION

FREQUENTLY ASKED QUESTIONS ABOUT THE WI-FI CONNECTION

• Which Wi-Fi protocols are supported?
  The installed Wi-Fi adapter supports Wi-Fi b/g/n connectivity for European countries.

• Which settings need to be configured in the router software?
  The following settings are required for the router: 2.4 GHz enabled, WiFi b/g/n, DHCP and NAT activated.

• Which WPS version is supported?
  WPS 2.0 or later versions. See the router documentation.

• Is there any difference between Android and iOS Smartphones (or Tablets)?
  There is no difference; either operating system can be used.

• Is it possible to use tethering via a mobile phone connection instead of a router?
  Yes, but the cloud services are designed for devices with a permanent connection.

• How can I check that my home Internet connection is working and that wireless functionality is enabled?
  You can search for your smart device in the network. Before trying, disable all other data connections.

• How can I check that the appliance is connected to my home Wi-Fi network?
  Access the router configuration (see the router manual) and check that the MAC address of the appliance is present in the list of connected wireless devices.

• Where can I find the appliance’s MAC address?
  Directly on the appliance:
  look for the label containing the SAID and MAC addresses.
  The MAC address consists of a combination of numbers and letters starting with “88:e7”.

• How can I check whether the wireless functionality of the appliance is enabled?
  Using the Smartphone or Tablet, check in the Whirlpool 6th Sense Live App that the appliance’s network is visible and connected to the cloud.

• What might prevent the signal from reaching the appliance?
  Check that the connected devices do not occupy the available bandwidth completely.
  Check that the number of devices enabled for Wi-Fi connection does not exceed the maximum limit supported by the router.

• How fare should the router be from the appliance?
  Usually, the Wi-Fi signal has enough strength to cover a couple of rooms, but the actual range depends largely on the materials the walls are made of. The signal strength can be checked by placing your Smartphone or Tablet near the appliance.

• What can I do if the wireless connection does not reach the appliance?
  Specific devices can be used to extend the coverage of your home Wi-Fi network, for example, access points, Wi-Fi repeaters and Power-line bridges (not included with the appliance).

• Where can I find the name and password for the wireless network?
  See the router documentation. Usually, there is a label on the router containing the information required to access the configuration page using a connected device.

• What can I do if the router uses my neighbor’s Wi-Fi channel?
  Force the router to use the home Wi-Fi channel.

• What can I do if the connection status light keeps flashing slowly and does not remain lit steadily, or if a stable connection with the home router cannot be established?
  It is possible that the appliance connects to the router but is not able to access the Internet. To connect the appliance to the Internet, check the router and/or line settings.

  • Router settings: NAT must be active, Firewall and DHCP must be configured correctly. Encryption types supported for passwords: WEP, WPA,WPA2. If you want to use a different type of encryption, see the router manual.
  • Line settings: if the Internet service provider has set the number of MAC addresses that can connect to the Internet, you may not be able to connect the appliance to the cloud. The MAC address is a unique identifier and it is different for each device. You will have to ask your provider about the procedure to follow to connect devices other than computers to the Internet.

• How can I check if data is being transmitted?
  After configuring the network, switch the appliance off, wait 20 seconds and switch it on again: check that the App shows the status of the user interface of the appliance.
  Some settings take several seconds to appear in the App.

• Can the Whirlpool 6th account be changed while keeping the appliances connected?
  It is possible to create a new account, but it is necessary to revoke the association of your appliances with the old account before associating them with the new one.

• What do I need to do if I change my router?
  It is possible to keep the same configuration parameters (network name and password) or delete the previous settings from the appliance and repeat the configuration procedure.

MAINTENANCE

• Cleaning: For cleaning, simply use a cloth moistened with neutral liquid detergents. Do not use cleaning tools or instruments.

• Anti-Grease Filter: It must be cleaned once a month (or when the filter saturation indication system – if any – indicates the need for it), with non-aggressive detergents, either by hand or in a dishwasher at a low temperature and on a short cycle.
  When cleaned in the dishwasher, the metal grease filter may discolour, but its filtering characteristics remain unchanged.

• The Anti-Grease Filter traps the grease particles produced during cooking. When cleaned in the dishwasher, the metal grease filter may discolour, but its filtering characteristics remain unchanged.

  • Carbon filter (for filter version only): The cartridge must be replaced at least every four months. It CANNOT be washed or regenerated. As indicated in the drawings section: remove the anti-grease filters, apply a carbon filter on each side and attach it to the product. Put the anti-grease filters back in place.

Illumination

• The lighting system is based on LED technology. LEDs provide optimal illumination, last up to 10 times longer than conventional lamps and save 90% of electricity.
  • Lighting system: The lighting system cannot be replaced by the user, contact Customer Service in case of malfunction.

END-OF-LIFE DISPOSAL

This device is marked in compliance with the European Directive 2012/19/EC – UK SI 2013 No.3113, Waste Elec-trical and Electronic Equipment (WEEE). Make sure that this product is disposed of correctly. The user helps prevent potential negative consequences for the environment and for health. The symbol on the product or accompanying documentation indicates that this product should not be treated as household waste but should be handed over at a suitable collection point for the recycling of electrical and electronic equipment. Dispose of it in accordance with local regulations for waste disposal. For further information about the treatment, recovery and recycling of this product, please contact your local authority, the collection service for household waste or the shop from where the product was purchased.
The packaging material is 100% recyclable and is marked by the recycling symbol

REGULATIONS
Equipment designed, tested and manufactured in compliance with safety regulations: EN/IEC 60335-1; EN/IEC 60335-2-31, EN/IEC 62233. Performance: EN/IEC 61591; ISO 5167-1; ISO 5167-3; ISO 5168; EN/IEC 60704-1; EN/IEC 60704-2-13;EN/IEC 60704-3; ISO 3741; EN 50564; IEC 62301. EMC: EN 55014-1; CISPR 14-1; EN 55014-2; CISPR 14-2; EN/IEC 61000-3-2; EN/IEC 61000-3-3.

OPERATING ERRORS

If something does not seem to be working, perform the following simple checks before contacting the Service Centre:

If the hood is not working:

• Check that:
  • There is no power failure
  • A speed has been selected
  • If the hood has poor performance:
• Check that:
  • The selected motor speed is sufficient for the amount of fumes and steam released.
  • The kitchen is sufficiently ventilated to allow an air intake.
  • The carbon filter is not worn out (hood in filtration version).
  • If the hood has switched off during normal operation:
• Check that:
  • There is no power failure.
  • The safety cut-off device has not tripped.

In the event of any malfunctions, disconnect the appliance from the electrical power supply for at least 5 seconds by unplugging it and then reconnect it, before contacting the Service Centre. If the malfunction persists, contact the Service Centre.

TECHNICAL SPECIFICATIONS

• Height (cm): 110-129,5
• Width (cm): 89,8
• Depth (cm): 32
• Ø of the exhaust pipe (cm): 15

Components not supplied with product

To download the safety instructions, user manual, technical data sheet and energy data:

• Visit the website docs.whirlpool.eu
• Use the QR code
• Alternatively, contact Customer Service (using the phone number indicated on the warranty booklet). When contacting Customer Service, communicate the codes on the product rating plate.

References

• caldo.Se
• Whirlpool Docs

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>