Laekerrt BLCT01 Personal Blender Instruction Manual

Laekerrt BLCT01 Personal Blender Instruction Manual

Important Safeguards

warning! To avoid the risk of serious injury, carefully read all instructions before operating this blender. When using any electrical appliance, basic safety precautions should always be observed, including the following important information.

1. Save this instruction manual for future use.

2. Never leave this blender unattended while it is in use.

3. Plug the blender to household outlet of 120V only and use the blender only for the intended use.

4. This blender can be used by persons with reduced physical, sensory, and mental capabilities or lack of experiences with the knowledge about the blender, if they have been given supervision or instructions concerning the use of the blender by a person responsible for their safety and when they are aware of possible risks.

5. Do not let children use the blender or carry out cleaning and maintenance of the blender. Keep the cord out of reach of children.

6. The blades are very sharp, please be extremely careful when assembling, dissembling, and cleaning them. Unplug the blender before assembling, dissembling, and cleaning the blender.

7. To prevent hazard, do not put the cord, the base, and the plug into water or any kinds of liquids.

8. Do not keep the cord hanging or place it near/on any hot surfaces (e.g. stove).

9. Do not operate the blender without a break. The maximum length of usage is 1 minute. Continuously operating the blender will lead to an increase in
   temperature of the interior components of the motor section which in turn makes the blender stop to operate. Therefore, we suggest stop operating the blender for 4 minutes after operating it for 1 minute.

10. Never start the blender without first locking the bottle in place.

11. Do not operate the blender when there is nothing in the bottle.

12. Do not operate the blender with a damaged cord or plug or after the blender malfunctions, or when it is damaged in any forms. Do not use or replace non-original accessories and parts to avoid any forms of danger.

13. Do not blend hot liquids.

14. Household use only.

Know Your Blender

How To Use The Blender

1. Please wash the components of the blender according to the “Cleaning and Maintenance” section on page 5 before your very first use.
2. Place the motor section on a flat, stable surface.
3. Fill the bottle with ingredients. The maximum capacity is 600 ml/20 oz (see level marks on the bottle) and must not be exceeded. For best results, we recommend filling the bottle with liquid ingredients first and then fresh/frozen ingredients (cut the ingredients into appropriate size).
4. Once finishing loading the ingredients to the bottle, attach and screw the blade unit on top of the bottle. Please flip the bottle over and then turn the bottle with the blade unit on the motor clockwise until they match the blade unit’s padlock with the symbol ” on the edge of the motor unit.
5. Plug in and start the blender by pressing the power switch. Once the desired results have been achieved. Release the switch. The mixing process is complete.
6. Take out the bottle by twisting it to the “ ” position and turn it upright so that the blade unit is facing downwards and twist the blade unit counter-clockwise to take the blade unit off. Then twist the spout lid supplied to the bottle. The bottle is ready to drink from or take away with you.

Caution:

1. This blender is not suitable for mixing potatoes, cream, egg whites, dough, and etc.
2. Do not operate the blender without a break. The maximum length of usage is 1 minute. Continuously operating the blender will lead to an increase in temperature of the interior components of the motor section which in turn makes the blender stop to operate. Therefore, we suggest stop operating the blender for 4 minutes after operating it for 1 minute.
3. Please lift the bottle and the blade unit once you unscrew them from the motor and turn them upright to prevent leaking.
4. Screw the blade unit securely onto the bottle’s opening. Make sure that the transparent sealing ring is in place in the blade unit before starting the blender.
5. The bottle with the blade unit on the motor unit should be matching the blade unit’s padlock with the symbol “ ” on the edge of the motor unit . Turn the bottle clockwise until it locks in place.
6. The blender is ready to use when the activation start button underneath the blade base is no longer possible to press down. This is the only way to secure the blade unit into the motor unit and get the blenderto start

Cleaning and Maintenance

For dissembling: the lid, the sealing rings, the blade unit, and the bottle can all be detached.
CAUTION! Handle the blade unit with care.
Always unplug the blender prior to cleaning and maintenance.

• Do not use harsh chemical solvent or any other abrasive products to clean.
  Bottles, blade unit and bottle lid are dishwasher safe (see special instructions for sealing rings later in this section).
  Use a damp cloth when cleaning the motor unit.
  Remove any stubborn stains by soaking and rubbing with a soft cloth and mild detergent.

• After use, clean the bottle immediately before the mixtures dry out.
  This makes cleaning much easier.

• Dry all parts thoroughly by wiping them or letting them air-dry.

Cleaning sealing rings:

• When cleaning the blender, the sealing ring must be removed from the blade unit in order to remove any residues.
• Unscrew the blade unit from the bottle. CAUTION! The blades are very sharp.
• Loosen the sealing ring by inserting a pointy-and-skinny object beneath the sealing ring and lifting it up.
• Hand-wash and dry the sealing rings. Then use the pointy-and-skinny object to press the sealing ring to its correct position. There is a risk of leakage if the sealing ring is not correctly replaced.

Troubleshooting

1. The blender is not plugged in.
2. The blade is not installed properly
3. The activation start button is pressed down.

|

1. Connect it to a power supply. 2.Install and twist the blade properly according to this instruction manual.
2. Unscrew the blade unit and restore the activation start button to the proper position whichallows the blades to operate.

The blender stops during operation.|

1. The blender is overheated.
2. Too many ingredients or the ingredients are too large.
3. Improper ingredients like hot liquids, hard substances with rind, and etc.

|

1. Switch off your blender immedi­ately and wait for 4 minutes before operating it again.
2. Put fewer/take out some ingredi­ents or cut the ingredients into smaller pieces
3. Do not put in ingredients with rind.

Excess pulp building up in the bottle.|

1. The fruits or vegetables are too hard to cut into smaller pieces.

| 1.Stop the blender. Scrape off or remove the pulp before continuing to blend.
Juice leaks between
the rim of the bottle
and the motor base.|

1. Too many ingredients in the bottle.
2. The sealing ring is improperly installed
3. The bottle is neither lifted nor turned upright right after unscrewing the bottle./
4. The blade unit is not securely screwed onto the bottle.

|

1. Unplug the blender and take out a portion of the ingredients or push the ingredients down a bit.
2. Use the pointy-and-skinny object to press the sealing ring to the proper position
3. Lift the bottle once you unscrew the bottle from the motor and make it upright to prevent leaking
4. Screw the blade unit securely onto the bottle’s opening.

Warranty

Each Laekerrt blender enjoys a 1-year limited warranty since the date of purchase. For more information, please visit our website (www.- laekerrt.com) or contact us directly.

Disclaimer

WE ARE NOT RESPONSIBLE FOR DAMAGES CAUSED BY THE FOLLOWINGS:

1. Misunderstanding and misuse of the instruction manual.
2. Instances other than the blender’s intended purpose.
3. Modifying the blender by consumers instead of technicians from authorized retailers or Likert.
4. Usage of non-original gadgets.

support@laekerrt.com
www.laekerrt.com
Laekerrt

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>