AIPHONE JP Series Video Door Station with HID Prox Point Installation Guide
- June 13, 2024
- AIPHONE
Table of Contents
AIPHONE JP Series Video Door Station with HID Prox Point
Product Information
The JP-DVF-PR is a video door station from the JP Series that comes with a built-in AC-PROX-1G proximity card reader. It is designed to connect directly to a JP-4MED master station using a 2-conductor wire. The card reader utilizes a standard Wiegand connection to connect to a compatible access control system.
Product Usage Instructions
To flush mount the JP-DVF-PR, recess the supplied back box into the wall. Then, attach the mounting bracket using the four provided bracket screws.
- Back Box Dimensions: 10-1/2 H x 5-13/16 W x 2-5/16 D
- JP-DVF-PR Dimensions: 11-11/16 H x 7 W x 2-1/16 D
For surface mounting, use the SBX-IDVFRA surface mount box. This box can be mounted to a standard single-gang box or any flat surface. To insert the transparent nameplates, remove the vandal-resistant front panel from the flush mount back box. Peeloff the protected seals from both sides of the plate. Write in the desired text, leaving 1 inch of white space on the right side. Insert the nameplate into the opening.
Wiring
Refer to the provided wiring diagram for connecting the JP-DVF-PR to the
JP-4MED master station and the access control host. For the card reader’s
Wiegand connection, follow the specified conductor functions:
- Red: 5 ~ 16V DC
- Black: Ground
- Green: Data 0
- White: Data 1
- Brown: Red LED
- Orange: Green LED
- Yellow: Card Present Beeper
- Blue: flower
- Violet: Shield Ground
- Drain: For proper regulatory compliance, disconnect the drain wire at the power supply end of the cable
FCC Warning
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. For more details about the features and information above, please contact Technical Support. Aiphone Corporation www.aiphone.com | 800-692-0200
Names and Functions
- Camera
- Microphone
- White LED for low light illumination
- Speaker
- Directory card
- Call button
- Card reader
Features
- PTZ camera
- Stainless steel faceplate
- Built-in RFID card reader
Package Contents
Installation
- For flush mounting, recess the supplied back box into the wall, then attach the mounting bracket using the four provided bracket screws.
- Back Box Dimensions: 10-1/2″ H x 5-13/16″ W x 2-5/16″ D
- JP-DVF-PR Dimensions: 11-11/16″ H x 7″ W x 2-1/16″ D
- For surface mounting, use the SBX-IDVFRA surface mount box.
- This box can mount to a standard single-gang box or to any flat surface.
- To insert the transparent nameplates, remove the vandalresistant front panel from the flush mount back box. Peel off theprotected seals from both sides of the plate. Write in the desired text, being sure to leave 1″ of white space on the right side. Insert the nameplate into the opening.
Wiring Diagram
Specifications
Door Station
- Camera Unit: 1/4″ color CMOS
- Scanning Line: 525 lines
- Min. illumination: 5 Lux
- Terminations: Screw terminals
- Operating Temp: -4°~140°F (-20°~60°C)
- Wiring Distance: 330′
- Dimensions: 11-11/16″ H x 7″ W x 2-1/16″ D
- w/ SBX-IDVFRA: 11-11/16″ H x 7″ W x 3-5/16″ D
Card Reader
- Reader Type: 125kHz Proximity Card Reader
- Reader Model: AC-PROX-1G
- Power Source: 5 ~ 16V DC
- Current: 30mA (average); 75mA (peak)
- Terminations: Color-coded pre-wired pigtail
- Wiring Distance: 500′
- Operating Temp: -31°~150°F (-35°~66°C)
- Operating Humidity: 0% to 90% relative humidity non-condensing
FCC WARNING:
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference that may cause undesired operation.
For proper regulatory compliance, the drain wire should be disconnected at the power supply end of the cable. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. For more details about the features and information above, please contact Technical Support.
- Aiphone Corporation
- www.aiphone.com .
- 800-692-0200
The JP-DVF-PR is a JP Series video door station with a built-in AC-PROX-1G proximity card reader. The station connects directly to a JP-4MED master station using 2-conductor wire, and the card reader uses a standard Wiegand connection to connect to a compatible access control system.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>