Amico Chemetron Gas Control Panel User Manual
- June 10, 2024
- Amico
Table of Contents
Amico Chemetron Gas Control Panel
Important Note
Due to unknown factors of the existing equipment, projects requiring Retro-Fit Conversions must be fully investigated by the installer.
It is the responsibility of the installer to determine if the Retro-Fit will function correctly and if additional components are required. Amico is not responsible for any additional components required.
Retro-Fit Instructions
Remove the screws from the Chemetron Gas Control Panel.|
---|---
Remove all internal components.|
Mount the filler frame to the wall using the appropriate hardware for the type
of wall you are mounting to. There are 6 holes provided for mounting the
frame, 3 on top and 3 on the bottom. NOTE: The frame cannot be mounted on
the wall centered on the existing back box. The retrofit is shipped with the
filler frame attached to the control panel. Before you take these apart, push
the assembly into the existing back box and position it into place and mark
off the corners of the frame on the wall. These lines will be your reference
for mounting the frame to the wall.|
The pigtail adapter and the reducer bushing, provided with the retrofit kit,
should be secured to the input and output in the back box as shown.|
The pigtail that is supplied in the retrofit kit is for the output. Secure the
male end to the reducer bushing on the output side in the back box.|
Secure the male end of the output pigtail to the output on the back of the
control panel. Secure the input pigtail, coming from the back of the control
panel, to the input in the back box. Push the whole assembly gently into the
back box and secure the panel to the filler frame using the #8 stainless steel
machine screws provided with the kit. Please note the position of the
pigtails. Make sure you position them this way or you may have trouble fitting
the panel onto the frame.|
Diagrams
Repair kit part #: N-X-TUBE-KIT
- Item numbers with * is included in the repair kit with 1 set of copper piping
| Item | Description | Part Number |
|---|---|---|
| 1 | 2 1/2″ Gauge, 0-400 psi, 1/4″ Center Back Mount | M-X-MAN-52B |
| 2* | Brass Tee 1/4″ FNPT* 3/8″ Tube | N-X-TEE-AL-F304 |
| 3 | Regulator Relieving | N-X-REGULATOR-R |
| 4 | Shut-off Valve (Brass) | N-X-VALVE |
| 5* | Elbow 90° 3/8″ MNPT* 3/8″ Tube | N-X-ELBW-AL-M37 |
| 6 | Brass Tee 1/4″ FNPT* 3/8″ Tube | N-X-TEE-AL-F304 |
| 7* | Connector 3/8″ MNPT* 3/8″ Tube | N-X-CON-AL-375 |
| 8 | Bushing 1/2″ * 3/8″ | N-X-BUSH |
| 9* | Elbow 90° 1/4″ MNPT* 1/8″ Tube | N-X-ELB-ALM2508 |
| 10* | Elbow 90° 1/4″ FNPT* 1/8″ Tube | N-X-ELB-ALF2508 |
| 11* | Elbow 90° 1/4″ FNPT* 3/8″ Tube | N-X-ELBOW-AL |
| 12a | DISS Demand Check Valve 1/4″ MNPT – Nitrogen | S-DIS-DEMC-NIT |
| 12b | DISS Demand Check Valve 1/4″ MNPT – Instrument Air | S-DIS-DEMC-IAIR |
| 13* | Elbow 90° 1/2″ MNPT* 3/8″ Tube | N-X-ELBW-AL-305 |
| 14 | 18″ Long Braided Pigtail (3/8″ inner diameter) | N-X-PIGTAIL |
| 15 | Pigtail/Pipe Adapter for Nitrogen Control Panel | N-X-PT-ADAPTER |
| 16 | Box for Nitrogen Control Panel | N-X-BOX |
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>