ECHO SRM-260 Grass Trimmer Brush Cutter User Manual

Grass Trimmer/Brush Cutter
Operator’s Manual

SRM-260 Grass Trimmer Brush Cutter

MODELS
SRM – 260
SRM – 260S
Serial Number 05001001 – 05999999

WARNING
The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.
WARNING
Specifications, descriptions and illustrative material in this literature are as accurate as known at the time of publication, but are subject to change without notice. Illustrations may include optional equipment and accessories, and may  not include all standard equipment.
Read and understand operator’s manual (and safety manual if included) before use. Failure to read the manuals could result in serious injury.
X7732274700
© 12/2017 ECHO Inc.

INTRODUCTION

This product was designed and manufactured to provide long life and onthe-job dependability.
Read and  understand this manual(and safety manual if included).
Keep the manuals in a safe place for future reference.
The operators manual contains specifications and information for safety, operation, maintenance, storage and assembly specific to this product.
Scan the QR codes throughout the operator’s manual for more information.
The safety manual explains possible hazards and the measures you should take to insure safe operation.
For questions regarding terms used in this manual, visit:

https://www.echo-usa.com/Support-Help/TechnicalDocuments?gt=true

OR

https://www.shindaiwa-usa.com/Tech-Support/TechnicalDocuments.aspx?gt=true

SERVICING INFORMATION

Parts/Serial Number
Genuine ECHO Parts and
Assemblies for your ECHO products are available only from an
Authorized ECHO Dealer. When you do need to buy parts always have the Model Number and Serial
Number of the unit with you. For future reference write them in the space provided below.
Model No.
Serial No.

SAFETY

Service
Service of this product during the warranty period must be performed by an Authorized ECHO Service Dealer. For the name and address of the Authorized ECHO Service Dealer nearest you, ask your retailer or call: 1-800-432-ECHO (3246). Dealer information is also available on our Web Site www.echo- usa.com. When presenting your unit for Warranty service/repairs, proof of purchase is required.
Echo Consumer Product Support
If you require assistance or have questions concerning the application, operation, or maintenance of this product, call the ECHO Consumer Product Support Department at 1-800-673-1558 from 8:00 am to 5:00 pm (Central Standard  Time) Monday through Friday. Before calling, please know the model and serial number of your unit.
Product Registration
Register your ECHO equipment on-line at www.echo-usa.com or by filling out the product registration sheet included in this manual. Registering your product confirms warranty coverage and provides a direct link to ECHO if we find it  necessary to contact you.
Additional or Replacement Manuals
Replacement Operator or Safety Manuals, and Parts Catalogs, are available from your Authorized ECHO Service Dealer, or at www.echo-usa.com, or by contacting ECHO Inc., 400 Oakwood Road, Lake Zurich, IL 60047 (800-673-1558).  Always check www .echo-usa.com for updated information.
Safety Videos are available from your Authorized ECHO Service Dealer. A $5.00 shipping charge is required for each video.

https://www.shindaiwa-usa.com/Tech-Support/Technical-Documents.aspx?gt=true

Manual Safety Symbols and Important Information
Throughout this manual and on the product itself, you will find safety alerts and helpful, informational messages preceded by symbols or key words. The following is an explanation of those symbols and key words and what they mean to you.

The safety alert symbol accompanied by the word “DANGER” calls attention to an act or condition which WILL lead to serious personal injury or death if not avoided.

The safety alert symbol accompanied by the word “WARNING” calls attention to an act or condition which CAN lead to serious personal injury or death if not avoided.

The safety alert symbol accompanied by the word “CAUTION” calls attention to an act or condition which may lead to minor or moderate personal injury if not avoided.

The enclosed message provides information necessary for the protection of the unit.
Note: This enclosed message provides tips for use, care and maintenance of the unit.
CIRCLE AND SLASH SYMBOL
This symbol means the specific action shown is prohibited.
Ignoring these prohibitions can result in serious or fatal injury.

International Symbols

Mixture
| Wear Eye, Ear and Head Protection| T| Carburetor Adjustment – Idle Speed
| Wear Hand and Foot Protection| L| Carburetor Adjustment – Low Speed Mixture
| Safety/Alert| | Emergency Stop
| Hot Surface| | Fuel and Oil Mixture
| Do not operate without guards and shields in place.| | Do not use blades.
String line only.
| Avoid all power lines.
This unit is not insulated against electrical  current.| | Plan retreat path from falling objects
| DO NOT Allow Flames or Sparks Near Fuel| | Ignition ON / OFF
| DO NOT Smoke Near Fuel| | Primer Bulb
| Choke Control “RUN” Position (Choke Open)| | Choke Control “COLD
START” Position (Choke Closed)
| Keep Bystanders and Helpers Away 15 m (50 ft.).| | Rotating Cutting Attachment
| Do not exceed 10,000 RPM| | Wear slip resistant footwear

Personal Condition and Safety Equipment

Burn Hazard
The muffler or catalytic muffler and surrounding cover may become extremely hot. Always keep clear of exhaust and muffler area, otherwise serious personal injury may occur.

Users of this product risk injury to themselves and others if the unit is used improperly and/or safety precautions are not followed. Proper clothing and safety gear must be worn when operating unit.
Physical Condition
Your judgment and physical dexterity may not be good:

• If you are tired or sick
• If you are taking medication
• If you have taken alcohol or drugs
  Operate unit only if you are physically and mentally well.

Eye Protection

◆ Eye protection that meets ANSI Z87.1 or CE requirements must be worn whenever you operate the unit.
◆ For additional safety, a full-face shield may be worn over safety glasses or goggles to provide protection from sharp branches or flying debris.
Hand Protection
Wear sturdy, no-slip, rubber work gloves to improve your grip on the handles. Gloves also provide protection against cuts and scratches, cold environments, and reduce the transmission of machine vibration to your hands.
Hearing/Ear Protection
ECHO recommends wearing hearing protection whenever unit is used.
Breathing Protection
Operators who are sensitive to dust or other common airborne allergens may need to wear a dust mask to prevent inhaling these materials while operating unit. Dust masks can provide protection against dust, plant debris, and other plant matter such as pollen. Make sure the mask does not impair your vision, and replace the mask as needed to prevent air restrictions.
Proper Clothing
Wear snug-fitting, durable clothing:

•  Pants should have long legs, shirts should have long sleeves.
• DO NOT WEAR SHORTS.
• DO NOT WEAR TIES, SCARVES, JEWELRY, or clothing with loose or hanging items that could become entangled in moving parts or surrounding growth.
• Keep clothing buttoned or zipped, and keep shirt tails tucked in.

Wear sturdy work shoes with nonskid rubber soles:

• DO NOT WEAR OPEN TOED SHOES.
• DO NOT OPERATE UNIT BAREFOOTED.
  Keep long hair away from engine and air intake. Retain hair with cap or net. Heavy protective clothing can increase operator fatigue, which may lead to heat stroke. Schedule heavy work for early morning or late afternoon hours when temperatures are cooler.

The components of this machine generate an electromagnetic field during operation, which may interfere with some pacemakers. To reduce the risk of serious or fatal injury, persons with pacemakers should consult with their physician and the pacemaker manufacturer before operating this machine. In the absence of such information, ECHO does not recommend the use of this machine by anyone who has a pacemaker.
Extended Operation/Extreme Conditions

Prolonged exposure to cold and/or vibration may result in injury. Read and follow all safety and operation instructions to minimize risk of injury. Failure to follow instructions may result in painful wrist/hand/arm injuries.
It is believed that a condition called Raynaud’s Phenomenon, which affects the fingers of certain individuals, may be brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning sensations, followed by loss of color and numbness in the fingers.
The following precautions are strongly recommended, because the minimum exposure, which might trigger the ailment, is unknown.

• Keep your body warm, especially the head, neck, feet, ankles, hands, and wrists.

• Maintain good blood circulation by performing vigorous arm exercises during frequent work breaks, and also by not smoking.

• Limit the hours of operation. Try to fill each day with jobs where operating the unit or other handheld power equipment is not required.

• If you experience discomfort, redness, and swelling of the fingers followed by whitening and loss of feeling, consult your physician before further exposing yourself to cold and vibration.

Repetitive Stress Injuries (RSI)
It is believed that overusing the muscles and tendons of the fingers, hands, arms, and shoulders may cause soreness, swelling, numbness, weakness, and extreme pain in those areas. Certain repetitive hand activities may put you at a high  risk for developing a Repetitive Stress Injury (RSI). An extreme RSI condition is Carpal Tunnel Syndrome (CTS), which could occur when your wrist swells and squeezes a vital nerve that runs through the area. Some believe that prolonged exposure to vibration may contribute to CTS. CTS can cause severe pain for months or even years.

To reduce the risk of RSI/CTS, do the following:

• Avoid using your wrist in a bent, extended, or twisted position. Instead try to maintain a straight wrist position. Also, when grasping, use your whole hand, not just the thumb and index finger.
• Take periodic breaks to minimize repetition and rest your hands.
• Reduce the speed and force with which you do the repetitive movement.
• Do exercises to strengthen the hand and arm muscles.
• Immediately stop using all power equipment and consult a doctor if you feel tingling, numbness, or pain in the fingers, hands, wrists, or arms. The  sooner RSI/CTS is diagnosed, the more likely permanent nerve andmuscle damage  can be prevented.

Equipment

Use only ECHO attachments. Serious injury may result from the use of a non- approved attachment combination. ECHO, INC. will not be responsible for the failure of cutting devices, attachments or accessories which have not been tested and approved by ECHO. Read and comply with all safety instructions listed in this manual and safety manual.

• Check unit for loose or missing nuts, bolts, and screws.
  Tighten or replace as needed.

• Inspect shield for damage and ensure that the cut-off knife is securely in place. Replace if either is damaged or missing.

• Check that the cutting attachment is firmly attached and in safe operating condition.

• Check that handle and harness (if included) are adjusted for safe, comfortable operation. See Assembly Section for proper adjustment.

http://www .echo-usa.com/videos

Moving parts can amputate fingers or cause severe injuries.
Keep hands, clothing and loose objects away from all openings.

• ALWAYS stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit.
• DO NOT start or operate unit unless all guards and protective covers are properly assembled to unit.
• NEVER reach into any opening while the engine is running.
  Moving parts may not be visible through openings.

Periodically Check fuel system (fuel lines, vent, grommet, fuel tank, and fuel cap) for leaks especially if the unit is dropped. If damage or leaks are found, do not use unit, otherwise serious personal injury or property damage may occur.  Have unit repaired by an authorized servicing dealer before using.

EMISSION CONTROL (EXHAUST & EVAPORATIVE)
CARB And EPA Emissions Control Information
The emission control system for the engine is EM (engine modification) and, if the second to last character of the Engine Family on the Emission Control Information label (sample below) is “B”, “C”, “K”, or “T”, the emission control  system is EM and TWC (3-way catalyst). The fuel tank/fuel line emission control system is EVAP (evaporative emissions). Evaporative emissions for California models are only applicable to fuel tanks.

An Emission Control Label is located on the engine. (This is an EXAMPLE ONLY, information on label varies by engine FAMILY). Product Emission Durability (Emission Compliance Period)
The 50 or 300 hour emission compliance period is the time span selected by the manufacturer certifying the engine emissions output meets applicable emissions regulations, provided that approved maintenance procedures are followed  as listed in the Maintenance Section of this manual.

DESCRIPTION

Locate the safety decal(s) on your unit. Make sure the decal(s) is legible and that you understand and follow the instructions on it. If a decal cannot be read, a new one can be ordered from your ECHO dealer. The safety decal is for example only. Your label may appear slightly different. 

1. Power Head
2. Throttle Handle – For Right Hand
3. Stop Switch
4. Support Handle – For Left Hand
5. Drive Shaft Assembly
6. Nylon Cutter Head
7. Debris Shield with Cut-Off Knife
8. Cut-Off Knife
9. Throttle Trigger
10. Top Guard
11. Spark Arrestor Muffler or Spark Arrestor Muffler with Catalyst
12. Fuel Tank
13. Recoil Starter/Handle
14. Fuel Tank Cap
15. Purge Bulb
16. Choke
17. Air Cleaner
18. Spark Plug

CONTENTS

The ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictions, some assembly may be necessary.
After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts. Use the contents list to check for missing parts.

1. 1 Power Head / Drive Shaft Assembly
2. 1 Operator’s Manual
3. 1 Safety Manual
4. 1 Warranty Statement
5. 1 Safety Glasses
6. 1 Echo Power Blend X™
7. 2-Stroke Oil Sample
8. 12 Pieces of pre-cut Nylon Line
9. 1 Shield Assembly

ASSEMBLY

Shield Installation
Parts Required: Shield Assembly.

Cut-off knife on debris shield has sharp edges. Avoid contact when installing or removing line head.

Wear Gloves or personal injury may result:

• Cut-off knife is sharp.
• Gear case and surrounding area may be hot.

1. Remove wing nut (A), washer (B), and bolt (C).
2. Snap the shield over the bearing housing.
3. Install bolt (C), washer (B), and wing nut (A).

Support Handle
Note: Label shows minimum spacing for Support Handle location.
Note: Support Handle is preinstalled.
Re-positioning and tightening is all that is required.

OPERATION

1. Position Support Handle (A) in comfortable operating position and tighten wing nut (B). The cutting attachment should be 5 – 7.5 cm (2 – 3 in.) above the ground and as level as possible.

Moving parts can amputate fingers or cause severe injuries.
Keep hands, clothing and loose objects away from all openings.
Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit.
Engine exhaust IS HOT, and contains Carbon Monoxide (CO), a poison gas. Breathing CO can cause unconsciousness, serious injury, or death. Exhaust can cause serious burns. ALWAYS position unit so that exhaust is directed away from your face and body.
Operation of this equipment may create sparks that can start fires around dry vegetation. This unit is equipped with a spark arrestor to prevent discharge of hot particles from the engine.
Metal cutters can also create sparks if the cutter strikes rocks, metal, or other hard objects. Contact local fire authorities for laws or regulations regarding fire prevention requirements.

Mixing Instructions

1. Fill an approved fuel container with half of the required amount of gasoline.
2. Add the proper amount of 2-stroke oil to gasoline.
3. Close container and shake to mix oil with gasoline.
4. Add remaining gasoline, close fuel container, and remix.

Fuel to Oil Mix — 50:1 Ratio

US| Metric
Gas| Oil| Gas| Oil
gal.| fl.oz.| L| cc
1| 3.| 5| 100
2| 5.| 10| 200
5| 13| 25| 500

Spilled fuel is a leading cause of hydrocarbon emissions. Some states may require the use of automatic fuel shut-off containers to reduce fuel spillage.

• Empty the fuel tank prior to storing the unit. Return unused fuel to an approved fuel storage container.
  Storage
  – Fuel storage laws vary by locality. Contact your local government for the laws affecting your area. As a precaution, store fuel in an approved, airtight container.
  Store in a well-ventilated, unoccupied building, away from sparks and flames.

http://www.echo-usa.com/Videos/Safety/Trimmer-Safety

Starting Cold Engine

The attachment will operate immediately when the engine starts, and could result in possible serious injury. Keep movable parts of the attachment away from objects that could become entangled or thrown, and surfaces that could cause loss of control.

1. Stop Switch Move stop switch (A) away from the STOP position.
2. Choke Move choke (B) to COLD START ( ) (closed) position.
3. Purge Bulb Pump purge bulb (C) until fuel is visible and flows freely in the clear fuel tank return line. Pump bulb an additional 4 or 5 times.
4. Recoil Starter
   

Lay the unit on a flat area and keep movable attachment parts clear of all obstacles. Firmly grasp throttle handle with left hand and fully depress throttle trigger to wide open position.
Rapidly pull recoil starter handle/rope (D) until engine fires (or maximum five pulls).

Starting Warm Engine
The starting procedure is the same as Cold Start except DO NOT close the choke, and do not depress throttle trigger to wide open position.
The attachment should not move at idle, otherwise serious personal injury may result.
Note: If attachment moves, readjust carburetor according to “Carburetor Adjustment” instructions in this manual or see your ECHO Dealer.

1. Stop Switch
   Move stop switch (A) away from the STOP position.

2. Purge Bulb
   Pump purge bulb (C) until fuel is visible and flows freely in the clear fuel tank return line. Pump bulb an additional 4 or 5 times.
   

3. Recoil Starter
   Lay the unit on a flat area and keep movable attachment parts clear of all obstacles. Firmly grip throttle handle with left hand.
   Rapidly pull recoil starter handle/rope (D) until engine fires.
   Note: If engine does not start  after 5 pulls, use Cold Start Procedure.

Stopping Engine
If engine does not stop when stop switch is moved to STOP position, close choke – COLD START position – to stall engine.
Have your ECHO dealer repair stop switch before using unit again.

1. Throttle
   Release throttle and allow engine to return to idle before shutting off engine.

2. Stop witch
   Move stop switch (A) to STOP position.

MAINTENANCE

Moving parts can amputate fingers or cause severe injuries.
Keep hands, clothing and loose objects away from all openings.
Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit. Allow unit to cool before performing service. Wear gloves to protect hands from sharp edges and hot surfaces.
Your ECHO unit is designed to provide many hours of trouble free service.
Regular scheduled maintenance will help your unit achieve that goal. If you are unsure or are not equipped with the necessary tools, we recommend that you take your unit to an ECHO Servicing Dealer for maintenance. To help you decide whether you want to DO-IT-YOURSELF or have the ECHO Dealer do it, each maintenance task has been graded. If the task is not listed, see your ECHO Dealer for repairs. Skill Levels
Level 1 = Easy to do. Common tools may be required.
Level 2 = Moderate difficulty. Some specialized tools may be required.
Level 3 = See your dealer.
Click HERE or go to http://www.echo-usa.com/products/maintenance-kit for information on Maintenance Kits.

Moving parts can amputate fingers or cause severe injuries.
Keep hands, clothing and loose objects away from all openings.
Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit. Allow unit to cool before performing service. Wear gloves to protect hands from sharp edges and hot surfaces.

Your ECHO unit is designed to provide many hours of trouble free service. Regular scheduled maintenance will help your unit achieve that goal. If you are unsure or are not equipped with the necessary tools, we recommend that you take  your unit to an ECHO Servicing Dealer for maintenance. To help you decide whether you want to DO-IT-YOURSELF or have the ECHO Dealer do it, each maintenance task has been graded. If the task is not listed, see your ECHO Dealer  for repairs.

Skill Levels
Level 1 = Easy to do. Common tools may be required.
Level 2 = Moderate difficulty. Some specialized tools may be required.
Level 3= See your dealer.
Click HERE or go to http://www.echo-usa.com/products/maintenance-kit for information on Maintenance Kits.

Maintenance Intervals

COMPONENT/SYSTEM| MAINTENANCE
PROCEDURE| REQURED
SKILL LEVEL
---|---|---
Daily or Before Use
Air Filter| Inspect/Clean| 1
Choke Shutter
Fuel System| Inspect (2)| 1
Cooling System| Inspect/Clean| 2
Recoil Starter Rope| Inspect/Clean| 1
Screws/Nuts/Bolts| Inspect/Tighten/ Replace*
Every Refuel
Fuel System| Inspect(2)| 1
3 Months

IMPORTANT NOTE – Time intervals shown are maximum. Actual use and your experience will determine the frequency of required maintenance.
MAINTENANCE PROCEDURE NOTES:

1. Apply lithium based grease every 25 hours of use.
2. Low evaporative fuel tanks DO NOT require regular maintenance to maintain emission integrity.

• Replacement is recommended based on the finding of damage or wear during inspection.

Air Filter
Level 1.
Parts Required: Tune-Up Kit

1. Close choke (COLD START [ ] position). This prevents dirt from entering the carburetor throat when the air filter is removed. Brush accumulated dirt from air cleaner area.

2. Remove air filter cover. Brush dirt from inside cover.

3. Replace filter if it is damaged, fuel soaked, very dirty, or the rubber sealing edges are deformed.
   • Lightly brush debris from filter.
   • Soak heavily soiled filters in water/detergent solution to loosen dirt, then brush lightly.
   • Rinse with clean water and allow to dry completely before reuse.

4. Install air filter in air filter case.

5. Install air filter cover.

Fuel Filter
Level 1.
Parts Required: Tune-Up Kit

Fuel is VERY flammable. Use extreme care when mixing, storing or handling, or serious personal injury may result.

1. Use a clean rag to remove loose dirt from around fuel cap and empty fuel tank.

2. Pull the fuel filter from the fuel tank.
   Do not damage fuel line while removing fuel filter from tank.

3. Remove the filter from the line and install the new filter.

Note: Federal EPA regulations require all model year 2012 and later gasoline powered engines produced for sale in the United States to be equipped with a special low permeation fuel supply hose between the carburetor and fuel tank. When servicing model year 2012 and later equipment, only fuel supply hoses certified by EPA can be used to replace the original equipment supply hose. Fines up to $37,500.00 may be enforced for using an non-certified replacement  part.

Spark Plug
Level 2.
Parts Required: Tune-Up Kit
Use only NGK BPM8Y spark plug (BPMR8Y in Canada) otherwise severe engine damage may occur.

1. Remove spark plug and check for fouling, worn and rounded center electrode.

2. Clean the plug or replace with a new one. DO NOT sand blast to clean. Remaining sand will damage engine.

3. Adjust spark plug gap by bending outer electrode.

4. Tighten spark plug to 150 – 170 kgf cm (130 – 150 in lbf).

Cooling System
Level 2.
To maintain proper engine operating temperatures, cooling air must pass freely through the cylinder fin area. This flow of air carries combustion heat away from the engine.
Overheating and engine seizure can occur when:

• Air intakes are blocked, preventing cooling air from reaching the cylinder.
• Dust and grass build up on the outside of the cylinder. This build up insulates the engine and prevents the heat from leaving.

Removal of cooling passage blockages or cleaning of cooling fins is considered “Normal Maintenance.”
Any failure attributed to lack of maintenance is not warranted.

1. Remove spark plug lead.

2. Remove air cleaner cover (A).

3. Remove engine cover (B).
   DO NOT use a metal scraper to remove dirt from the cylinder fins.

4. Use a brush to remove dirt from the cylinder fins.

5. Remove ignition wires from clip for cleaning.

6. Remove grass and leaves from the grid between the recoil starter and fuel tank.

7. Assemble components in reverse order.

Exhaust System
Spark Arrestor Screen
Level 2.
Parts Required: Spark Arrestor Screen, Gasket

1. Remove spark plug lead and engine cover.

2. Place piston at Top Dead Center (TDC) to prevent carbon/dirt from entering cylinder.

3. Remove spark arrestor screen cover (C), gaskets (D), (E), and screen (F), from muffler body.

4. Clean carbon deposits from muffler components.
   Note: When cleaning carbon deposit, be careful not to damage the catalytic element inside muffler.

5. Replace screen if it is cracked, plugged, or has holes burned through.

6. Assemble components in reverse order.

Exhaust Port Cleaning
Level 2.
Parts Required: As needed: Heat Shield

1. Remove spark plug lead from spark plug, and remove engine cover.

2. Place piston at top dead center Remove muffler (A) and heat shield (B).
   

3. Use a wood or plastic scraping tool to clean deposits from cylinder exhaust port (C).
   Never use a metal tool to scrape carbon from the exhaust port. Do not scratch the cylinder or piston when cleaning the exhaust port. Do not allow carbon particles to enter the cylinder.

4. Inspect heat shield, and replace if damaged.

5. Install heat shield and muffler.

6. Tighten muffler mounting bolts (or nuts) to 90 – 110 kgf•cm (80 – 95  in•lbf).

7. Install engine cover and attach spark plug lead.

8. Start engine, and warm to operating temperature.

9. Stop engine, and re-tighten mounting bolts (or nuts) to specifications.

Carburetor Adjustment
Level 2.

Engine Break-In
New engines must be operated a minimum duration of two tanks of fuel break-in before carburetor adjustments can be made. During the break-in period your engine performance will increase and exhaust emissions will stabilize. Idle speed can be adjusted as required.
High Altitude Operation
This engine has been factory adjusted to maintain satisfactory starting, emission, and durability performance up to 330 m (1100 ft.) above sea level (ASL) (96.0 kPa). To maintain proper engine operation and emission compliance above  330 m (1100 ft.) ASL the carburetor may need to be adjusted by an authorized ECHO service dealer.

If the engine is adjusted for operation above 330 m (1100 ft.) ASL, the carburetor must be re-adjusted when operating the engine below 330 m (1,100 ft.) ASL, otherwise severe engine damage may result.
Note: Every unit is run at the factory and the carburetor is set in compliance with emission regulations. Carburetor adjustments, other than idle speed, must be performed by an authorized ECHO dealer.

1. Check idle speed and reset if necessary. If a tachometer is available, idle speed screw (A) should be set to the specifications found on “Specifications” page of this manual. Turn idle screw (A) clockwise to increase idle speed;  counterclockwise to decrease idle speed.
   

When carburetor adjustment is completed, the cutting attachment should not move at idle, otherwise serious personal injury may result.

Lubrication
Level 1.
Parts Required:
Lithium Based Grease.

1. Remove shield.
2. Loosen bearing housing locating screw (A), at the top of the housing, loosen mounting screw (B) and remove gear case from drive housing.
3. Pull the flexible drive shaft (C) from the drive housing, wipe clean and apply 15 ml (0.5 oz.) of grease.
4. Slide the flexible drive shaft back in the drive housing being careful not to get dirt on the flexible drive shaft.
5. Install the bearing housing and shield.

Wear gloves or personal injury may result:
◆ Cutoff knife is sharp.
◆ Gearcase and surrounding area may be hot.

1. Cut one piece of line to recommended length.
   2.0 mm (0.080 in.) diameter 6 m (20 ft.).
   2.4 mm (0.095 in.) diameter
   6 m (20 ft.).

2. Align arrows on top of knob with openings in eyelets.

3. Insert one end of trimmer line into an eyelet, and push line equal distance through trimmer head.
   

4. Hold trimmer head while turning knob clockwise to wind line onto spool until about 13 cm (5 in.) of each line remains exposed.
   Trimmer head is now fully loaded and ready for operation.

When the wear indicators located at the bottom of the Speed-Feed® head are worn smooth, or if holes appear, replacement of the cover or the entire Speed- Feed® head is required.

Nylon Line Head
Disassembly
Instructions
Note: For normal use, Speed Feed® head disassembly is not necessary. However, if circumstances require disassembly, follow these instructions.

TROUBLESHOOTING

1. Press top of locking tabs (A) on both sides of Speed Feed® head to release cover (B) from eyelet carrier (C).
2. Remove cover from eyelet carrier.

Fuel vapors are extremely flammable and may cause fire and/or explosion. Never test for ignition spark by grounding spark plug near cylinder plug hole, otherwise serious personal injury may
result.

ENGINE PROBLEM TROUBLESHOOTING CHART

Problem| Check| Status| Cause| Remedy
Engine starts
hard or Engine  does not start| Fuel at carburetor| No fuel at carburetor| Fuel strainer or fuel line obstructed| Clean or replace
See your Echo dealer

STORAGE

During operation the muffler or catalytic muffler and surrounding cover become hot. Always keep exhaust area clear of flammable debris during transportation or when storing, otherwise serious property damage or personal injury may result.
Long Term Storage (Over 30 Days)
Do not store your unit for a prolonged period of time (30 days or longer) without performing protective storage maintenance which includes the following:

1. Store unit in a dry, dust free place, out of the reach of children.
   Do not store in enclosure where fuel fumes may accumulate or reach an open flame or spark.

2. Place the stop switch in the “OFF” position.

3. Remove accumulation of grease, oil, dirt and debris from exterior of unit.

4. Perform all periodic lubrication and services that are required.

5. Tighten all the screws and nuts.

6. Drain fuel tank completely. Press purge bulb 6 – 7 times to remove remaining fuel from carburetor then drain the tank again. Close choke, start and run the engine until it stops due to lack of fuel.

7. Allow engine to cool. Remove the spark plug lead from the spark plug.
   Remove the spark plug. Pour 7 cc (0.25 oz.) of fresh, clean, two-stroke engine oil into the cylinder through the spark plug hole.

8. Pull the recoil starter handle 2 – 3 times to distribute the oil inside the engine.

9. Observe the piston location through the spark plug hole. Pull the recoil handle slowly until the piston reaches the top of its travel and leave it there.

10. Install the spark plug. Connect the spark plug lead to the spark plug.

SPECIFICATIONS

13738. and J.A.S.O. M345- E12, two-stroke, air-cooled engine oil.
       Gasoline| Use 89 Octane unleaded. Do not use fuel containing methyl alcohol, more than 10% ethyl alcohol or 15% MTBE. Do not use alternative fuels such as E-15 or E-85.
       Oil| Power Blend XTM or ECHO Red Armor® Premium Universal 2-Stroke Oil
       Fuel Tank Capacity| 420 mL (14.2 US fl. oz.)
       Starter System| Automatic Rewind Starter
       Clutch| Centrifugal Type
       Drive Shaft| 6 mm (1/4 in.) flexible shaft
       Rotating Direction| Clockwise; viewed from top
       Cutter Head| Speed Feed® Nylon line head, Line capacity 6.0 m (20 ft.) .080 or .095 line
       Handles| Support Handle, Throttle Handle
       Shoulder Harness| Optional P/N 99944200201

PRODUCT REGISTRATION

PRODUCT REGISTRATION
Thank you for choosing ECHO Power Equipment
Please go to http://www.echo-usa.com/Warranty/Register-Your-ECHO to register your new product on-line. It’s FAST and EASY! NOTE: your information will never be sold or misused by ECHO, Inc. Registering your purchase enables  us to contact you in the unlikely event of a service update or product recall, and verifies your ownership for warranty consideration.
If you do not have access to the Internet, you can complete the form belowand mail to:
ECHO Inc., Product Registration, PO Box 1139, Lake Zurich IL 60047.

ECHO, INCORPORATED
400 Oakwood Road
Lake Zurich, IL 60047
www.echo-usa.com

References

• Outdoor Power Equipment & Tools | ECHO
• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>