ZODIAC Z400iQ Pool Heat Pump Instruction Manual
- June 13, 2024
- Zodiac
Table of Contents
ZODIAC Z400iQ Pool Heat Pump
Product Information
- Product Name: Z400iQ
- Language: French (FR)
- User Manual: Spare Parts/Accessories Instructions Manual – English
- Product Code: H0789700_REVA – 2022/06
- Supplied Parts: 1 x Z400iQ
For any further assistance or queries, please visit our website www.zodiac.com
Safety Instruction
WARNING – This product must be installed and serviced by a qualified professional with sufficient experience in pool equipment installation and maintenance so that all of the instructions in the product’s complete installation and operations manual can be followed exactly. All safety instructions in the complete manual must be followed explicitly in order to prevent injury hazards. Improper installation and/or operation will void the warranty.
WARNING/SHOCK HAZARD – Turn off all switches and the main circuit breaker
of the electric circuit for the appliance before beginning the
installation. Failure to comply may cause a shock or hazard resulting in
severe personal injury or death. While disconnecting and/or connecting any
electrical wiring in the appliance, be careful not to damage or abrade any of
the wiring.
The qualified technician working on the appliance must use/wear personal protective equipment (such as safety goggles and protective gloves, etc.) in order to reduce the risk of injury occurring when working on the appliance.
Tools
-
PH2 cross-head screwdriver
-
PH2 short cross-head screwdriver
-
TORX T40 screwdriver
Not supplied
- Heating cable x 1
- Screw x 14
- Clip x 14
- Insulation pad x 14
Supplied
If the firmware version is earlier than R52, a firmware update is required to
finalize the position change of the heating cable.
It is recommended to replace the bottom conveyor on heat pump models who were
not initially equipped with a heating cable. Check for the required spare kit
in the catalog before you begin the installation.
Switch off the appliance before you start any operation.
Installation
-
Remove the front panel and the top panel of the heat pump.
-
Open the electrical box.
-
Remove the tape. Disconnect the fan cable. Disconnect the earth wire in the electrical box.
-
Remove the T40 plastic Torx screw. Keep it close to be reused.
-
Remove the heating cable (part not reused). Remove the propeller.
-
Remove the tape from each side of the air conveyor.
-
Remove the top air conveyor then the bottom air conveyor. On MD7/TD7 models, the intermediate wedge must also be removed.
-
Put the heating cable on the base respecting the positioning of the clips (changes depending on the base size, see page 9). Fit the heating part of the cable in the gutter under the evaporator.
-
Place the insulation pads (supplied) over the point of the screws below the base to protect the installer from injury.
-
Disconnect D08 (yellow wires). Disconnect connector on D07 and use it to connect the heating cable on D08 output (connect the connector of the new heating cable). Check accordance with new electrical wiring attached.
On the MD7/TD7 models, the intermediate wedge has to be replaced to be able to pass the heating cable in the base.
- Put the lower air conveyor then the upper air conveyor back. Check if replacing the conveyor is required.
- Connect the earth wire in the electrical box, then connect the fan cable. Put back the tape over the cables..
-
Put back the tape on both sides of the air conveyor.
-
Put back the T40 plastic torx screw.
-
Close the electrical box.
-
Put back the front panel and the top panel of the heat pump.
Check the firmware version. If it is an earlier version than R52, the firmware must be updated on the unit.
Dimension
Z400iQ – R32
Z400iQ – R410
Connecting point of the heating cable has been updated, see dotted circle.
Large base
Inside
Outside
Petite base
Inside
Outside
www.zodiac.com
©2022 Zodiac Pool Systems LLC. All rights reserved. ZODIAC® is a registered
trademark of Zodiac International, S.A.S.U., used under license. All other
trademarks are the property of their respective owners.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>