RTS81TY Raptor Series Magnum RT Drop Steps Instructions

RTS81TY Raptor Series Magnum RT Drop Steps

Product Information

• Product Name: MAGNUM RT STEPS
• SKU: RTS81TY

Components:

• Passenger Side Step Bar Qty 1
• Driver Side Step Bar Qty 1
• Front Brackets Qty 2
• Center/Rear Brackets Qty 4

Tools Required:

• RATCHET
• TORQUE WRENCH
• 13MM SOCKET

Hardware:

• M8 x 30 mm Hex Head Bolts Qty 18
• M8 Hex Head Nuts Qty 6
• M8 Flat Washers Qty 24
• Front Armor Plates Qty 2
• M8 Lock Washers Qty 24
• RTSPN175 Bolt/Nut Plates Qty 6
• M8 Plastic Push Nuts Qty 6

Torque Specifications: For Rocker Panel Mount Installations, M8 through M12 bolts and nuts are set to 15-20 ft lbs.

Product Usage Instructions

1. Remove all contents from the package and check steps for any damage. Also, verify that all components and hardware listed above are included before you begin installation.

2. Read the installation manual and installation drawing completely. Understand all brackets and bolts before installation.

3. Begin installation on the passenger side. Align brackets as shown in the installation drawing.

4. Align brackets with existing factory threaded holes in the rocker panel. These holes may have black plugs in them that will need to be removed before installation. Fasten each bracket to the rocker panel using two (2) M8 x 30mm Hex Head Bolts, two (2) M8
   Lock Washers and two (2) M8 Flat Washers per bracket. Use the appropriate set of holes as indicated in the installation drawing.

5. Line up mounting points on the step bar with the mounting holes in each bracket.

6. Fasten the step bar to each bracket using one (1) RTSPN175 Bolt/Nut Plate, one (1) Plastic Push Nut, one (1) M8 Hex Head Nut, two (2) M8 Lock Washers, two (2) M8 Flat Washers, and one (1) M8 x 30MM Hex Head Bolt.

7. Adjust the bars front/back and up/down to the desired placement. Once you have the step positioned, tighten until the split lock washer is flat between the bolt head and flat washer. Do not over-tighten.

8. When all hardware is in place, everything must be tightened according to the provided torque specifications. Repeat these steps for opposite-side installation.

Optional: If you wish to install the Front Armor Plates, follow these steps:

1. Thoroughly clean the front side of the front step where the Front Armor Plate will attach.
2. Remove adhesive protection from the Front Armor Plate.
3. Carefully line up with the front side of the front step. Be careful not to let the side overhang as they could peel off over time.
4. Once lined up, firmly press the Front Armor Plate on the step to ensure complete adhesion. Repeat these steps for the opposite side.

Components

Hardware

Tools Required

Torque Specifications

• For Rocker Panel Mount Installations
• M8 through M12 bolts and nuts are set to 15-20 ft-lbs

Note : When installing the brackets and bars, all hardware must be left loose until all the items are attached

INSTALLATION

1. Remove all contents from the package and check steps for any damage. Also, verify that all components and hardware listed above are included before you begin installation.
2. Read the installation manual and installation drawing completely. Understand all brackets and bolts before installation.
3. Begin installation on the passenger side. Align Brackets as shown.
4. Align brackets with existing factory threaded holes in the rocker panel (4a). These holes may have black plugs in them that will need to be removed before installation. Fasten each bracket to the rocker panel using two (2) M8 x 30mm Hex Head Bolts, two (2) M8 Lock Washers, and two (2) M8 Flat Washers (4b) per bracket
5. Line up mounting points on the step bar with the mounting holes in each bracket.
6. Fasten the step bar to each bracket using one (1) RTSPN175 Bolt/Nut Plate, one (1) Plastic Push Nut, one (1) M8 Hex Head Nut, two (2) M8 Lock Washers, two (2) M8 Flat Washers and one (1) M8 x 30MM Hex Head Bolt.
7. Adjust the bars front/back and up/down to the desired placement. Once you have the step positioned, tighten until the split lock washer is flat between the bolt head and the flat washer. Do not over-tighten.
8. When all hardware is in place, everything must be tightened. See page 1 for torque specifications. Repeat these steps for opposite-side installation.

OPTIONAL:

If you wish to install the Front Armor Plates, begin by thoroughly cleaning the front side of the front step where the Front Armor Plate will attach.

1. Remove adhesive protection from the Front Armor Plate.
2. Carefully line up with the front side of the front step. Be careful not to let the side overhang as they could peel off over time.
   Once lined up, firmly press the Front Armor Plate on the step to ensure complete adhesion. Repeat these steps for the opposite side.

SKU : RTS81TY

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>