EXFO TK1-V2 Telecommunication Networks Fiber Optic Owner’s Manual
- June 13, 2024
- EXFO
Table of Contents
- KEY FEATURES
- APPLICATIONS
- OTDR TESTING
- OLTS TESTING
- OPTIMIZED PORTABILITY AND POWERFULL TESTING CAPABILITIES
- PACKAGED FOR EFFICIENCY
- CERTIFIER MODELS
- ONBOARD MULTISTANDARD CERTIFICATION
- OLTS TIER 1 BUILT-IN ENCIRCLED FLUX COMPLIANCY
- OTDR TIER 2 ENCIRCLED FLUX COMPLIANCY
- iOLM—REMOVING THE COMPLEXITY FROM OTDR TESTING
- FULL AUTOMATION OF THE OLTS
- Optimized Test Sequence
- FULLY AUTOMATED FIBER INSPECTION SCOPE
- POWERFUL CONNECTOR ENDFACE IMAGE VIEWING AND ANALYSIS SOFTWARE
- Fast track data post-processing with FastReporter2
- SPECIFICATIONS FOR FTB-940/945 TELCO OLTS (NETWORK SERVICE PROVIDER
- SPECIFICATIONS FOR FTB-940/945 FIBER CERTIFIER OLTS (ENTERPRISE MODELS)
- SPECIFICATIONS FOR OTDRS
- ORDERING INFORMATION—NETWORK SERVICE PROVIDER MODELS
- ORDERING INFORMATION—ENTERPRISE MODELS
- EI AND EA CONNECTORS
- Documents / Resources
EXFO TK1-V2 Telecommunication Networks Fiber Optic Owner’s Manual
KEY FEATURES
Lightweight and portable solution designed for field engineers or cell technicians who install, troubleshoot and maintain fiber networks
Ultra-bright 8-inch multitouch screen
Built-in connectivity—choose between gigabit interface, WiFi, Bluetooth and 3G or 4G LTE via USB dongle
Integrated tool combines a visual fault locator, 100% automated inspection probe, broadband power meter and a continuous wave (CW) source mode
Combined singlemode (SM)/multimode (MM) wavelengths (quad model)
APPLICATIONS
- FTTx construction
- Telecommunications and outside plant networks testing
- Data centers
- Enterprise structured cabling
OTDR TESTING
- Dynamic range up to 46 dB
- Event dead zone as low as 0.8 m
- iOLM-ready—one-touch multiple acquisitions with clear go/no-go results presented in a straightforward visual format
OLTS TESTING
- Unmatched FasTesT™ performances—100% automated bidirectional test at two wavelengths under five seconds
- Onboard assistant and diagnosis to reduce the risk of reference errors and negative loss
- Built-in Encircled-Flux (EF) compliancy as per ANSI/TIA and ISO/IEC
- iCERT models to certify multiple industry standards simultaneously
- Onboard professional PDF reporting
MaxTester 940/945 Telco OLTS
MaxTester 940/945 Fiber Certifier OLTS
Fiber inspection scope FIP-400B (WiFi or USB)
OPTIMIZED PORTABILITY AND POWERFULL TESTING CAPABILITIES
With EXFO’s world renowned automated features including FasTesT™ and iOLM,
this solution combines more than a decade of know-how and expertise into one
truly powerful test instrument. Optimize test routines during construction
with EXFO’s FasTesT™ automated OLTS (Tier 1) test routine, and test fibers bi-
directionally and error free within seconds. Locate faults within networks and
fully characterize fibers at the push of a button using EXFO’s iOLM automated
test routine.
PACKAGED FOR EFFICIENCY
- SM OTDR port
- SM Live or MM OTDR port
- SM OLTS port
- MM OLTS port
- Mic/headset jack
- Micro SD card slot
- 7 1 GigE port
- USB 3.0 port
- Two USB 2.0 ports
- Optional visual fault locator
- 1 OLTS power meter port
- High-power power meter (optional)
CERTIFIER MODELS
The TK1-V2 offers iCERT models for data center and enterprise Tier 1 fiber certification and designed to help installation contractors, network engineers and IT maintenance technicians achieve faster, first-time-right system acceptance.
ONBOARD MULTISTANDARD CERTIFICATION
- TIA
- IEC
- ISO
- IEEE
The iCERT certification tool lets you certify to both cabling and application standards. Simultaneously certify the cabling (i.e. the physical quality of the fiber and its components, such as splices and connectors), as well as the application that the fiber can carry; for instance, IEEE or Fibre Channel.
OLTS TIER 1 BUILT-IN ENCIRCLED FLUX COMPLIANCY
Each TK1-V2 comes with a built-in EF-compliant MM light source. Furthermore, in order to maximize measurement accuracy and avoid invalid results, EXFO designed reference-grade test cords in compliance with ISO/IEC 14763-3 standard requirements.
EXFO’s test cords are made from reference-grade connectors, and the fiber used is strictly controlled to ensure proper core size and geometry. For MM testing, this makes it possible to remain within Encircled Flux template limits at the output of the test cord, without the need for an external EF- mode conditioner. These high-quality, reference-grade test cords are less fragile and less expensive than EF-conditioned test cords, helping to reduce your overall equipment cost of ownership.
EXFO’s test cords are also color-coded to prevent manipulation errors when they are connected to the test ports and device under test. The user interface displays animated instructions with the same color codes to facilitate the test process.
OTDR TIER 2 ENCIRCLED FLUX COMPLIANCY
EXFO recommends using an external launch mode conditioner that is Encircled Flux (EF)-compliant. Use of an external EF-compliant device* such as the SPSB- EF-C30 is a fast and easy way to fix faulty networks.
Color coded test cords
SPSB-EF-C30
iOLM—REMOVING THE COMPLEXITY FROM OTDR TESTING
OTDR testing comes with its load of challenges…
-
WRONG OTDR TRACES
-
COUNTLESS TRACES TO ANALYZE
-
REPEATING THE SAME JOB TWICE
-
COMPLEX INSTRUMENT TRAINING/SUPPORT
In response to these challenges, EXFO developed a better way to test fiber optics : the iOLM is an OTDR-based application designed to simplify OTDR testing by eliminating the need to configure parameters, and/or analyze and interpret multiple complex OTDR traces. Its advanced algorithms dynamically define the testing parameters, as well as the number of acquisitions that best fit the network under test. By correlating multipulse widths on multiple wavelengths, the iOLM locates and identifies faults with maximum resolution—all at the push of a single button.
How does it work?
- DYNAMIC MULTIPULSE ACQUISITION
- INTELLIGENT TRACE ANALYSIS
- ALL RESULTS COMBINED INTO A SINGLE LINK VIEW
- COMPREHENSIVE DIAGNOSIS
Turning traditional OTDR testing into clear, automated, first-time-right
results for technicians of any skill level.
Three ways to benefit from the iOLM:
OTDR Combo (Oi Code)
Run iOLM and OTDR applications on one unit
Upgrade
Add the iOLM software option, even while in the field
iOLM only
Order a unit with the iOLM application only
Three iOLM feature value packs:
iOLM Standard
Dynamic multipulse acquisition, intelligent trace analysis, map view,
diagnosis and SOR trace generation
iOLM Advanced
All the features of iOLM, plus additional Advanced features
iOLM Pro
All the features of iOLM Advanced, plus additional high-value professional
features
Please refer to the iOLM specification sheet for the complete and most recent description of these value packs.
FULL AUTOMATION OF THE OLTS
Test Efficiency
-
FasTesT™: acquisition time in less than three seconds
-
Online reporting–live from the field
-
Maximum simplicity and fast-learning curve with on-board user assistance:
-
Port LED indicators: guide the user through the referencing and testing processes. LED indicators show the user on which optical port to connect the fiber and a beep indicates that the connection is established to confirm continuity.
-
On-board diagnosis: throughout the referencing and testing processes, the instrument delivers real-time information on the test cord health as well as pass/fail results according to pre-set or custom criteria. When performing testing, the instrument delivers diagnosis about the loss, length and can even identify the presence of a macrobend (refer to side picture).
-
Margin meters: indicate the result status as well as the margin according to preset thresholds.
On-board diagnosis helps the technician take proper action
-
The OLTS includes a Test Again feature allowing the user to re-test bad fibers in three easy steps:
- Go back to test results
- Quickly and correctly identify the bad fiber by looking at the pass/fail status
- Press Test Again
Optimized Test Sequence
- Real-time continuity feature: The main and remoteunits emit visual and audible signals to let the technicians on both ends know that a connection has been established on the specific fiber under test. This also allows the technicians to start the test right away, saving time on each fiber tested.
- Text messaging capabilities: Allows users to send text messages through the fiber under test faster than other test sets in the industry
See results clearly and test again easily
- Results tab lists all the fibers tested in a cable
- Pass/Fail status indicated under Results
- Test Again button allows re-testing a “failed fiber” using the same settings
FULLY AUTOMATED FIBER INSPECTION SCOPE
Neglecting to clean, inspect and certify connectors can lead to serious, time- consuming problems accounting for up to 80% of network failures.
With its two full-fledged units, the TK1-V2 lets you certify connectors at both ends of the fiber, in the same workflow as the Tier-1 certification. Accordingly, it is now easy to include connector certification in your regular method of procedures without compromising the efficiency of your technicians. You’ll no longer leave any stones unturned or any connectors uninspected!
Years of experience in the field has given EXFO the insight and expertise to re-engineer a truly unique and innovative fiber inspection probe that greatly simplifies and speeds up this critical step.
Housing a unique automatic focus-adjustment system, the FIP-400B automates each operation in the connector endface inspection sequence. The result: fiber inspection is now a quick, one-step process that can be performed by technicians of all skill levels
Automated models
The FIP-500: wireless, autonomous and fully automated scope featuring
the fastest inspection in the industry for both multifiber and single-fiber
connectors. All-day testing without the need to recharge batteries or offload
results.
The FIP-435B: connected to EXFO platforms or your smart device, this fully automated wireless scope enables connector certification in one step. View and store results on your EXFO platform or smart device.
The FIP-430B: fully automated inspection scope featuring USB wired connectivity to PC and EXFO platforms.
Semi-automated and manual models
The FIP-420B: semi-automated scope featuring a manual focus adjustment.
USB wired connectivity to PC and EXFO platforms.
The FIP-410B: basic inspection features for manual inspection. USB wired
connectivity to PC and EXFO platforms.
FEATURES | USB WIRED | WIRELESS | AUTONOMOUS |
---|---|---|---|
FIP-410B | FIP-420B | FIP-430B | FIP-435B |
Image capture | • | • | • |
Five-megapixel CMOS capturing device | • | • | • |
Automatic fiber image-centering function and focus adjustment | • | ||
• | • | • | |
Automatic fiber image-focus adjustment | • | ||
On-board pass/fail analysis | • | • | |
Pass/fail LED indicator | • | • | |
USB connectivity to an EXFO platform or PC | • | • | • |
Wireless connectivity to an EXFO platform or PC | |||
Wireless connectivity to a smartphone | |||
Semi-automated multifiber / MPO inspection | • | • | • |
Fully automated multifiber / MPO inspection | |||
On-board touch screen and data storage | |||
SmarTips with automated thresholds and quick-connect mechanism |
For more information, visit www.EXFO.com/fiberinspection.
POWERFUL CONNECTOR ENDFACE IMAGE VIEWING AND ANALYSIS SOFTWARE
- Automatic pass/fail analysis of the connector end faces
- Lightning-fast results in seconds with simple one-touch operation
- Complete test reports for future referencing
- Stores images and results for record-keeping
Fast track data post-processing with FastReporter2
Optical test-data analysis involves various challenges, whether for loss, OTDR and iOLM testing, or connector inspection. Designed for off-line analysis, EXFO’s FastReporter 2 offers reliable data and report management in a user- friendly environment. This unit packs all the essentials to boost efficiency and productivity for all your optical tests.
-
CHALLENGE
NO. 1
EDITING MULTIPLE MEASUREMENT FILES
Close your jobs faster
Measurements often require extra processing in order to perform proper analysis, and ultimately document and report jobs appropriately. FastReporter 2 includes a series of powerful tools that automate repetitive operations on an unlimited number of files via batch operations. -
CHALLENGE
NO. 2
ANALYZING MULTIPLE MEASUREMENT FILES
-
Wrong limits? Simply recertify
Setting up the wrong limits by selecting the wrong standard or the wrong project is no longer an issue. FastReporter 2 allows you to reset the limits and re-analyze the results to obtain the certification that you need. Instead of redoing tests, you can move on to other projects. -
CHALLENGE
NO. 3
DOCUMENTING YOUR WORK
Create your report fast and like a pro
FastReporter 2 generates professional, customized reports containing all test measurements under multiple formats (PDF, HTML and XLS). Your customer can now easily see and validate the quality of your work.
SPECIFICATIONS FOR FTB-940/945 TELCO OLTS (NETWORK SERVICE PROVIDER
MODELS)
POWER METER SPECIFICATIONS a
Detector type| InGaAs
Uncertainty b| ±(5 % + 32 pW)
Measurement range (dBm)| 5 to –75
Calibrated wavelengths (nm)| 850, 1270, 1290, 1300, 1310, 1330, 1350, 1370,
1383, 1390,1410, 1430, 1450, 1470, 1490, 1510, 1530, 1550, 1570, 1590, 1610,
1625, 1650
Tone detection (Hz)| 270/330/1000/2000
SOURCE SPECIFICATIONS a
| MM (850 nm/1300 nm): –25
Output power (dBm) c| SM1 (1310 nm/1550 nm): 2.5
| SM3 (1310 nm/1550 nm/1625 nm): 1 / –1 / –5
| SM4 (1310 nm/1490 nm/1550 nm): 1 / –5 / –1
Output power stability (dB)| ±0.05 over 8 h
Spectral width (FWHM) (nm)| 850 nm: 30 to 601300 nm: 100 to 150
FasTesT™ LOSS/LENGTH SPECIFICATIONS a
Testing speed c| FasTesT™ Simplex: 3 seconds (two wavelengths, bidirectional,
automated, IL + fiber length) FasTesT™ Simplex: 6 seconds (three wavelengths,
bidirectional, automated, IL + ORL + fiber length)
| SM (Laser)
| MM (LED)| 1310 ± 20
Wavelengths (nm) c| 850 ± 20| 1490 ± 10
| 1300 ± 20| 1550 ± 20
| 1625 ± 10
Launch condition d| Encircled Flux (EF) compliancy guaranteed at 50/125 µm MM
source port.Within TIA-526-14-B, ISO/IEC 14763-3 and IEC 61280-4-1 EF
templatelimits at the end of an EXFO reference-grade 50/125 μm test cord.
Loss range (dB) e| MM: 20SM Simplex: 45SM Duplex: 50
Length measurement range (km) f| MM: 20SM: 200
Length measurement uncertainty c| Duplex: ±(0.5 m + 0.5 % x length) Simplex:
±(1 m + 0.5 % x length)
ORL measurement range (dB) c, g| 50
ORL measurement uncertainty (dB) c, g, h| ±1
LASER SAFETY
CLASS 1
LASER PRODUCT
a. All specifications valid at 23 °C ± 1 °C and 1550 nm, on batteries
and after 15 minutes of warm up, unless otherwise specified.
b. Uncertainty is valid at calibration conditions.
c. Typical.
d. Measured at 850 nm with SC connector.
e. Typical value, at 850 nm for MM and 1550 nm for SM.
f. At 1300 nm for MM and 1550 nm for SM.
g. ORL measurement available on MAX-945 singlemode wavelengths only.
h. No discrete reflectance greater than —65 dB. Up to 45 dB.
SPECIFICATIONS FOR FTB-940/945 FIBER CERTIFIER OLTS (ENTERPRISE MODELS)
POWER METER SPECIFICATIONS a
Input connector| Interchangeable adapter (LC, SC or FC) b
Detector type| InGaAs
Uncertainty c| ±(5 % + 32 pW)
Measurement range (dBm)| 5 to –75
Calibrated wavelengths (nm)| 8850, 1270, 1290, 1300, 1310, 1330, 1350, 1370,
1383, 1390,1410, 1430, 1450, 1470, 1490, 1510, 1530, 1550, 1570, 1590, 1610,
1625, 1650
Tone detection (Hz)| 270/330/1000/2000
SOURCE SPECIFICATIONS
Output power (dBm) d| MM: –25SM: 2.5
Output power stability (dB)| ±0.05 over 8 h
Spectral width (FWHM) (nm)| 850 nm: 30 to 601300 nm: 100 to 150
FasTesT™ LOSS/LENGTH SPECIFICATIONS a
Testing speed d| FasTesT™ Duplex: 3 seconds (two wavelengths, one direction,
automated, IL + fiber length) FasTesT™ Simplex: 5 seconds (two wavelengths,
bidirectional, automated, IL + ORL + fiber length)
Input/Output connectors| Interchangeable adapter (LC, SC or FC) b
Wavelengths (nm) d| MM (LED) SM (Laser)850 ± 20
1310 ± 201300 ± 20 1550 ± 20
Launch condition e| EF compliancy guaranteed at MM source portWithin
TIA-526-14-B, ISO/IEC 14763-3 and IEC 61280-4-1 Encircled Flux template limits
at the end of an EXFO reference-grade 50/125 µm test cord
Length measurement range (km)| MM: 20 fSM: 200
Length measurement uncertainty d, g| ±(0.5 m + 0.5 % x length)
ORL measurement range (dB) d, h| 50
ORL measurement uncertainty (dB) d, h, i| ±1
LASER SAFETY
CLASS 1
LASER PRODUCT
a. At 23 °C ± 1 °C and 1550 nm, on batteries and after 15 minutes of
warm up, unless specified otherwise.
b. Specifications are provided with FC type connectors.
c. Uncertainty is valid at calibration conditions.
d. Typical.
e. Measured at 850 nm with SC connector.
f. At 1300 nm.
g. In duplex.
h. ORL measurement available on MAX-945 singlemode wavelengths only.
i. No discrete reflectance greater than —65 dB. Up to 45 dB.
SPECIFICATIONS FOR OTDRS
Refer to the individual OTDR spec sheets for details:
- FTB-720C access OTDR
- FTB-730C PON FTTx MDU OTDR
- FTB-735C metro PON FTTx MDU OTDR
- FTB-750C metro longhaul OTDR
ORDERING INFORMATION—NETWORK SERVICE PROVIDER MODELS
TK1-V2-XX-| XX| XX| XX| XX| XX| XX|
XX| XX| XX| XX| XX| XX| XX| XX
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---
Display S1 = Standard display S2 = Enhanced display for outdoor use|
WiFi/Bluetooth option 00 = Without RF components RF = With RF capability (WiFi
and Bluetooth)| Memory 64G = 64 GB internal memory (flash)| Power meter 00 =
Without power meter PM2X = Power meter; GeX detector VPM2X = VFL and power
meter; GeX detector| Power meter connector adapter a FOA-12 = Biconic FOA-14 =
NEC D4: PC, SPC, UPC FOA-16 = SMA/905, SMA/906 FOA-22 = FC/PC, FC/SPC, FC/UPC,
FC/APC FOA-28 = DIN 47256, DIN 47256/APC FOA-32 = ST: ST/PC, ST/SPC, ST/UPC
FOA-54B = SC: SC/PC, SC/SPC, SC/UPC, SC/APC FOA-78 = Radiall EC FOA-96B =
E-2000/APC FOA-98 = LC FOA-99 = MU| Inspection probe models b 00 = Without
inspection probe FP410B = Digital video inspection probe Triple magnification
FP420B = Analysis digital video inspection probe Automated pass/fail analysis
Triple magnification Autocentering FP425B = Wireless digital video inspection
probe c Automated pass/fail analysis Triple magnification Autocentering FP430B
= Automated analysis digital video inspection probe Automated focus Automated
pass/fail analysis Triple magnification Autocentering FP435B = Wireless
analysis digital video inspection probe c Automated focus Automated pass/fail
analysis Triple magnification Autocentering| Base tips APC = Includes
FIPT-400-U25MA and FIPT-400-SC-APC UPC = Includes FIPT-400-U25M and FIPT-400
-FC-SC| Extra FIP-400B tips d Bulkhead tips FIPT-400-FC-APC = FCAPC tip for
bulkhead adapter FIPT-400-FC-SC = FC and SC tip for bulkhead adapter e
FIPT-400-LC = LC tip for bulkhead adapters FIPT-400-LC-APC = LC/APC tip for
bulkhead adapter FIPT-400-MU = MU tip for bulkhead adapters FIPT-400-SC-APC =
SC APC tip for bulkhead adapter f FIPT-400-ST = ST tip for bulkhead adapter
Patchcord tips FIPT-400-U12M = Universal patchcord tip for 1.25 mm ferrules
FIPT-400-U12MA = Universal patchcord tip for 1.25 mm ferrules APC
FIPT-400-U16M = Universal patchcord tip for 1.6 mm ferrules FIPT-400-U20M2 =
Universal patchcord tip for 2.0 mm ferrules (D4, Lemo) FIPT-400-U25M =
Universal patchcord tip for 2.5 mm ferrules e FIPT-400-U25MA = Universal
patchcord tip for 2.5 mm ferrules APC f Multifiber tips g FIPT-400-MTP2 =
MTP/MPO UPC tip for bulkhead adapter FIPT-400-MTPA2 = MTP/MPO APC tip for
bulkhead adapter FIPT-400-MTP-MTR = MTP/MPO multirow UPC tip for bulkhead
adapter FIPT-400-MTP-MTRA = MTP/MPO multirow APC tip for bulkhead adapter Tip
kits FIPT-400-LC-K = LC tip kit including: FIPT-400-LC: LC tip for bulkhead
adapters, FIPT-400-LC-APC: LC/APC tip for bulkhead adapter, FIPT-400-U12M:
Universal patchcord tip for 1.25 mm ferrules, FIPT-400-U12MA: Universal
patchcord tip for 1.25 mm ferrules APC FIPT-400-LC-K-APC = LC tip kit
including: FIPT-400-LC-APC: LC/APC tip for bulkhead adapter, and
FIPT-400-U12MA: Universal patchcord tip for 1.25 mm ferrules APC
FIPT-400-LC-K-UPC = LC tip kit including: FIPT-400-LC: LC tip for bulkhead
adapters, and FIPT-400-U12M: Universal patchcord tip for 1.25 mm ferrules
FIPT-400-MTP-MTR-K = MTP/MPO multirow APC and UPC tip for bulkhead adapter g|
Software option 00 = Without any software option IPT = Ping and traceroute
functionalities EXpert-VoIP = RTP-based call testing software application,
including packet loss analysis, jitter measurement and complete voice quality
metrics EXpert-IP = IP/Ethernet test suite, with tests including FTP
performance, HTTP availability, VLAN scan, LAN discovery, ping, traceroute and
IP/ Ethernet port statistics (license for a single platform) EXpert-IPTV =
IPTV test suite EXpert-TPP-Bundle = Triple-play bundle for voice, video and
data testing; includes EXpert IP Test Tools, EXpert IPTV Test Tools, EXpert
VoIP Test Tools and EXpert SIP EXpert-SIP = SIP call-signaling support h
EXpert-SCCP = SCCP call-signaling support h EXpert-H.323 = H.323 call-
signaling support h EXpert-H.248 = H.248/Megaco call-signaling support h
FR2-PL = FastReporter 2 software Fiber characterization package FR2-PL-LB =
FastReporter 2 software Fiber characterization package and iOLM Loopback mode|
OTDR FTB-720C-SM1-XX = SM 1310/1550 nm FTB-720C-SM2 = SM Port 1: 1310/1550 nm
Port 2: Filtered 1625 nm for live fiber testing FTB-720C-Q1 = MM Port 1:
850/1300 nm Port 2: SM hardware ready and field upgradable to 1310/1550 nm
FTB-720C-Q1-QUAD = Quad Port 1: 850/1300 nm Port 2: 1310/1550 nm FTB-730C-SM1
= SM 1310/1550 nm FTB-730C-SM2 = SM Port 1: 1310/1550 nm Port 2: Filtered 1625
nm for live fiber testing FTB-730C-SM3 = SM 1310/1550/1625 nm FTB-730C-SM8 =
SM Port 1: 1310/1550 nm Port 2: Filtered 1625 nm for live fiber testing FTB-
730C-SM6 = SM, filtered 1625 nm for live fiber testing FTB-730C-SM7 = SM,
filtered 1650 nm for live fiber testing FTB-735C-SM1 = SM 1310/1550 nm FTB-
735C-SM2 = SM Port 1: 1310/1550 nm Port 2: Filtered 1625 nm for live fiber
testing FTB-735C-SM3 = SM 1310/1550/1625 nm FTB-735C-SM4 = SM 1310/1490/1550
nm FTB-750C-SM1 = SM 1310/1550 nm FTB-750C-SM3 = SM 1310/1550/1625 nm| Base
software OTDR = Enables OTDR application only iOLM = Enables iOLM application
only Oi = Enables OTDR and iOLM applications| iOLM software option i 00 = iOLM
standard iADV = iOLM advanced iPRO = iOLM pro iLOOP = iOLM loopback mode iCERT
= iOLM Tier 2 certification| OTDR connector EA-EUI-28 = APC/DIN 47256 EA-
EUI-89 = APC/FC narrow key EA-EUI-91 = APC/SC EA-EUI-95 = APC/E-2000 EA-EUI-98
= APC/LC EI connectors = See section on last page| OLTS FTB-940-SM1 = IL and
length measurement SM 1310/1550 nm FTB-945-SM1 = IL, length and ORL
measurement SM 1310/1550 nm FTB-945-SM3 = IL, length and ORL measurement SM
1310/1550/1625 nm FTB-945-SM4 = IL, length and ORL measurement SM
1310/1490/1550 nm FTB-945-iCERT-Q1-QUAD = Quad Port 1: 850/1300 nm IL and
length measurement Port 2: 1310/1550 nm IL, length and ORL measurement| OLTS
connector j EI-EUI-28 = UPC/DIN 47256 k EI-EUI-89 = UPC/FC narrow key l EI-
EUI-90 = UPC/ST k EI-EUI-91 = UPC/SC l EI-EUI-95 = UPC/E-2000 k EI-EUI-98 =
UPC/LC l EA-EUI-28 = APC/DIN 47256 k EA-EUI-89 = APC/FC narrow key EA-EUI-91 =
APC/SC EA-EUI-95 = APC/E-2000 k EA-EUI-98 = APC/LC
a. Available if power meter is selected.
b. Includes ConnectorMax2 software.
c. Requires RF capability (WiFi and Bluetooth hardware option).
d. This list represents a selection of fiber inspection tips that covers
the most common connectors and applications but does not reflect all the tips
available. EXFO offers a wide range of inspection tips, bulkhead adaptors and
kits to cover many more connector types and different applications. Please
contact your local EXFO sales representative or visit
www.EXFO.com/FIPtips for more information.
e. Included when UPC base tips are selected.
f. Included when APC base tips are selected.
g. Includes a bulkhead adapter for patchcord inspection.
h. Available if EXpert VoIP selected.
i. Please refer to the iOLM specification
sheet
for the complete and most recent description of these value packs.
j. Connector adapters are the same on SM source ports, MM source ports
and power meter ports. MM connectors are always UPC.
k. Not available for iCERT and FTB-945 models.
l. For FTB-945 model, a hybrid REF grade test cord will be supplied when
an EI (UPC) interface is required on the SM port. See EI section in this
document
ORDERING INFORMATION—ENTERPRISE MODELS
TK1-V2-XX-| XX| XX| XX| XX| XX| XX|
XX| XX| XX| XX| XX| XX| XX| XX
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---
Display S1 = Standard display S2 = Enhanced display for outdoor use|
WiFi/Bluetooth option 00 = Without RF components RF = With RF capability (WiFi
and Bluetooth)| Memory 64G = 64 GB internal memory (flash)| Power meter 00 =
Without power meter PM2X = Power meter; GeX detector VPM2X = VFL and power
meter; GeX detector| Power meter connector adapter a FOA-12 = Biconic FOA-14 =
NEC D4: PC, SPC, UPC FOA-16 = SMA/905, SMA/906 FOA-22 = FC/PC, FC/SPC, FC/UPC,
FC/APC FOA-28 = DIN 47256, DIN 47256/APC FOA-32 = ST: ST/PC, ST/SPC, ST/UPC
FOA-54B = SC: SC/PC, SC/SPC, SC/UPC, SC/APC FOA-78 = Radiall EC FOA-96B =
E-2000/APC FOA-98 = LC FOA-99 = MU| Inspection probe models b 00 = Without
inspection probe FP410B = Digital video inspection probe Triple magnification
FP420B = Analysis digital video inspection probe Automated pass/fail analysis
Triple magnification Autocentering FP425B = Wireless digital video inspection
probe c Automated pass/fail analysis Triple magnification Autocentering FP430B
= Automated analysis digital video inspection probe Automated focus Automated
pass/fail analysis Triple magnification Autocentering FP435B = Wireless
analysis digital video inspection probe c Automated focus Automated pass/fail
analysis Triple magnification Autocentering| Base tips APC = Includes
FIPT-400-U25MA and FIPT-400-SC-APC UPC = Includes FIPT-400-U25M and FIPT-400
-FC-SC| Extra FIP-400B tips d Bulkhead tips FIPT-400-FC-APC = FCAPC tip for
bulkhead adapter FIPT-400-FC-SC = FC and SC tip for bulkhead adapter e
FIPT-400-LC = LC tip for bulkhead adapters FIPT-400-LC-APC = LC/APC tip for
bulkhead adapter FIPT-400-MU = MU tip for bulkhead adapters FIPT-400-SC-APC =
SC APC tip for bulkhead adapter f FIPT-400-ST = ST tip for bulkhead adapter|
Software option 00 = Without any software option IPT = Ping and traceroute
functionalities EXpert-VoIP = RTP-based call testing software application,
including packet loss analysis, jitter measurement and complete voice quality
metrics EXpert-IP = IP/Ethernet test suite, with tests including FTP
performance, HTTP availability, VLAN scan, LAN discovery, ping, traceroute and
IP/Ethernet port statistics (license for a single platform) EXpert-IPTV = IPTV
test suite EXpert-TPP-Bundle = Triple-play bundle for voice, video and data
testing; includes EXpert IP Test Tools, EXpert IPTV Test Tools, EXpert VoIP
Test Tools and EXpert SIP EXpert-SIP = SIP call-signaling support h EXpert-
SCCP = SCCP call-signaling support h EXpert-H.323 = H.323 call-signaling
support h EXpert-H.248 = H.248/Megaco call-signaling support h FR2-PL =
FastReporter 2 software Fiber characterization package FR2-PL-LB =
FastReporter 2 software Fiber characterization package and iOLM Loopback mode|
OTDR FTB-720C-Q1 = MM OTDR module Port 1: 850/1300 nm, 27/29 dB (50/125 and
62.5/125 µm) Port 2: SM hardware ready and field upgradable to 1310/1550 nm
FTB-720C-Q1-QUAD = Quad OTDR module Port 1: 850/1300 nm, 27/29 dB (50/125 and
62.5/125 µm) Port 2: 1310/1550 nm, 36/35 dB (9/125 µm)| Base software OTDR =
Enables OTDR application only iOLM = Enables iOLM application only Oi =
Enables OTDR and iOLM applications| iOLM software option i 00 = iOLM standard
iADV = iOLM advanced iPRO = iOLM pro iLOOP = iOLM loopback mode iCERT = iOLM
Tier 2 certification| OTDR connector EA-EUI-28 = APC/DIN 47256 EA-EUI-89 =
APC/FC narrow key EA-EUI-91 = APC/SC EA-EUI-95 = APC/E-2000 EA-EUI-98 = APC/LC
EI connectors = See section on next page| OLTS certifier FTB-940-iCERT-SM1 =
Certification, IL and length measurement SM 1310/1550 nm FTB-940-iCERT-Q1=
Quad ready Port 1: 850/1300 nm IL and length measurement Port 2: SM hardware
ready and field upgradable to 1310/1550 nm FTB-940-iCERT-Q1-QUAD = Quad Port
1: 850/1300 nm IL and length measurement Port 2: 1310/1550 nm IL and length
measurement FTB-945-iCERT-Q1-QUAD = Quad Port 1: 850/1300 nm IL and length
measurement Port 2: 1310/1550 nm IL, length and ORL measurement| OLTS
connector j EI-EUI-89 = UPC/FC narrow key k EI-EUI-91 = UPC/SC k EI-EUI-98 =
UPC/LC k EA-EUI-89 = APC/FC narrow key EA-EUI-91 = APC/SC EA-EUI-98 = APC/LC
Example: TK1-V2-S1-RF-64G-PM2X-FOA-12-FP420B-APC-FIPT-400-FC-APC-IPTFTB- 720C-Q1-Oi-iADV-EA-EUI-28-FTB-940-iCERT-SM1-EA-EUI-89
a. Available if power meter is selected.
b. Includes ConnectorMax2 software.
c. Requires RF capability (WiFi and Bluetooth hardware option).
d. This list represents a selection of fiber inspection tips that covers
the most common connectors and applications but does not reflect all the tips
available. EXFO offers a wide range of inspection tips, bulkhead adaptors and
kits to cover many more connector types and different applications. Please
contact your local EXFO sales representative or visit
www.EXFO.com/FIPtips for more information.
e. Included when UPC base tips are selected.
f. Included when APC base tips are selected.
g. Includes a bulkhead adapter for patchcord inspection.
h. Available if EXpert VoIP selected.
i. Please refer to the iOLM specification sheet for the complete and most
recent description of these value packs.
j. Connector adapters are the same on SM source ports, MM source ports
and power meter ports. MM connectors are always UPC.
k. For FTB-945 model, a hybrid REF grade test cord will be supplied when
an EI (UPC) interface is required on the SM port. See EI section in this
document.
EI AND EA CONNECTORS
To maximize the performance of your FTBx-945 ORL measurements, APC connectors are mandatory on the SM port. These connectors generate lower reflectance, which is a critical parameter that affects performance for ORL measurement. APC connectors provide better performance than UPC connectors, thereby improving testing efficiency.
To maximize the performance of your OTDR, EXFO recommends using APC
connectors. These connectors generate lower reflectance, which is a critical
parameter that affects performance, particularly dead zones. APC connectors
provide better performances than UPC connectors, thereby improving testing
efficiency. Note: UPC connectors are also available, simply replace EA-XX
by EI-XX in the ordering part number. Additional connectors available are the
EI-EUI-76 (UPC/HMS-10/AG)
and EI-EUI-90 (UPC/ST).
EXFO headquarters
T +1 418 683-0211
Toll-free +1 800 663-3936 (USA and Canada)
EXFO serves over 2000 customers in more than 100 countries. To find your local office contact details, please go to www.EXFO.com/contact
For the most recent patent marking information, please visit
www.EXFO.com/patent. EXFO is certified ISO 9001
and attests to the quality of these products. EXFO has made every effort to
ensure that the information contained in this specification sheet is accurate.
However, we accept no responsibility for any errors or omissions, and we
reserve the right to modify design, characteristics and products at any time
without obligation. Units of measurement in this document conform to SI
standards and practices. In addition, all of EXFO’s manufactured products are
compliant with the European Union’s
WEEE directive. For more information, please visit
www.EXFO.com/recycle. C ontact EXFO for prices
and availability or to obtain the phone number of your local EXFO
distributor.
For the most recent version of this spec sheet, please go to www.EXFO.com/specs.
TK1V2.3EN © 2018 EXFO Inc. All rights reserved. Printed in Canada 18/03
Documents / Resources
| EXFO
TK1-V2 Telecommunication Networks Fiber
Optic
[pdf] Owner's Manual
TK1-V2 Telecommunication Networks Fiber Optic, TK1-V2, Telecommunication
Networks Fiber Optic, Networks Fiber Optic, Fiber Optic
---|---
References
- Contact | EXFO
- So You Think Fiber Inspection is a Hassle? | Video | EXFO
- Virtual patent marking | EXFO
- Environmental, social and governance (ESG) impact at EXFO | EXFO
- Technical documentation | Resources | EXFO
- iOLM | Link Characterization | Optical Fiber Testing | OTDR Trace | Loopback
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>