Hansshow V7-YXW 3 Power Trunk Instruction Manual
- June 13, 2024
- Hansshow
Table of Contents
Hansshow V7-YXW 3 Power Trunk
Product Information
- Product Name: Model 3 Power Trunk
- Model Number: V7-YXW
- Manufacturer: Hansshow
Aftersale Contact:
- Phone/WhatsApp: +86 130 4421 9654
- Email: support@hansshow.com.
Working Hours (UTC+8): 9:00 AM – 18:30 PM (Monday to Sunday)
Power Supply
- Fuse for Power Tailgate (with 25A specification)
- Connect with the Original Vehicle Fuse (if there is no fuse, no need to connect it)
- Schematic Diagram of Power Supply
- Fuse for Power Tailgate Connect to Original Vehicle Fuse
Product List
This drawing is for reference only, subject to the actual object.
- Power supply positive pole
- CAN plug
- Power supply negative pole
- Strut plugs for both sides
- Lower suction lock plug
- Rear button
- Trunk outside button adapter plug
- No need to connect
- Buzzer kick sensor
Product Usage Instructions
Height Adjustment
- Adjust the tailgate to the appropriate height.
- Press and hold the tailgate button for 5 seconds.
- A long sound indicates that the height setting is successful.
- When the tailgate is opened again, it will open to the set height.
Speed Adjustment
- The tailgate opening and closing speed has three gears: default gear of 4, lowest gear of 3, and highest gear of 5.
- Press the tailgate button.
- When the buzzer sounds 3 consecutive times, it means the third gear of speed is set successfully.
- When the buzzer sounds for 4 consecutive times, it means the fourth gear of speed is set successfully, and so on.
- Release the button after the desired gear sounds to complete the gear setting.
Note: After installation, a matching operation is required when the decoder is plugged in. Adjust the electric tailgate to the highest position, press and hold the added button on the tailgate for 5 seconds, and release the button after a long sound. This completes the matching operation. (Re-powering on requires re-matching operation)
Note: If the wiring to be connected is not specified in the manual, the wiring does not need to be installed.
Model 3 Power Trunk Installation Manual (V7-YXW)
Note:
- The installation instructions may differ slightly from the actual operation. If there are any differences, please follow the actual situation or contact us.
- Warning: Please do not disassemble any part by yourself, any improper operation will not be covered by our warranty.
Aftersale Contact:
phone/WhatsApp: +86 130 4421 9654 Email:
support@hansshow.com.
Working Hours (UTC+8):
9:00 AM – 18:30 PM (Monday to Sunday) Please leave a message at other times
power supply
Schematic diagram of power supply
The incoming end must be connected to the live end of the original vehicle’s current fuse hole. If it is connected reversely, it will cause the original vehicle’s fuse to fuse over-current. Before installation, the incoming end must be measured and determined with a measuring pen. The current direction is shown by the red line of the schematic diagram.
HOW TO USE
| original trunk button| Trunk Added button| Key Fob|
Central control screen| App Control
---|---|---|---|---|---
opening| single click| /| double-click| single click| single click
closing
|
/
|
single click
|
double-click
| step on the brake, then click the button|
single click
Note: the installation instructions may be slightly different from the actual operation. If there is any difference, please operate according to the actual situation or contact us.
Model 3 Power Trunk Installation Manual (V7-YXW)
Operating Instructions
Height Adjustment
Adjust the tailgate to the appropriate height, press the tailgate button for 5
seconds, and a long sound indicates that the height setting is successful.
When it is opened again, it will open to the set height.
Speed Adjustment
The tailgate opening and closing speed is divided into three gears, with the
default gear of 4, the lowest gear of 3, and the highest gear of 5. Press the
tailgate button, when the buzzer sounds for 3 consecutive times, it means that
the third gear of speed is set successfully.When the buzzer sounds for 4
consecutive times, it means that the fourth gear of speed is set successfully,
and so on. Release the button after the desired gear sounds, and the
gearsetting is successful.
After installation, the matching operation is required when the decoder is
plugged in: adjust the electric tailgate to the highest position, press the
added button on the tailgate for 5 seconds, and release the button after a
long sound, then the matching operation is completed (re-power on requires re-
matching operation)
Note: if the wiring to be connected is not specified in the manual, the
wiring does not need to be installed
Product List
Product List
This drawing is for reference only, subject to the actual
object
Installation Step
- Model 3 outward appearance
- Remove the original tailgate trim panel
- Remove the latch trim panel
- Remove the trim panel in the picture
- Peel the left and right trim panels of the trunk a little (to facilitate the disassembly of taillight screws).
- Remove the left and right tail lights of the original vehicle
- Remove the left and right hydraulic rods of the original vehicle (Note: block a piece of foam between the glass and the hydraulic rod when removing the hydraulic rod to prevent the glass from being scratched by improper operation)
- After remove the hydraulic rod of the original vehicle, install the electric strut supplied by our company (Note: after installing the strut, be sure to check whether the ball joint of the strut is stuck in place, and the wire end of the strut is towards the car body).
- Pass the strut wire through the reserved hole of the original vehicle in the picture above (the left andright are the same)
- After threading the strut wire from the reserved hole of the original vehicle, open the hole of the reserved hole rubber plug of the original vehicle and install the rubber plug back.
- Remove the lock block of the original vehicle and install the suction lock block delivered by our company.
- Stick the lock motor into the right trim panel of the trunk(as shown in the picture).
- Thread the tailgate detection wire 5SJ000A21 onto the tail cover from the position shown in the figure)
- Remove the trim panel under the armrest box
- Wiring Diagram
- Thread the CAN cable from the carpet under the passenger seat to the armrest box.
- Thread the can cable from the carpet under the passenger seat to the armrest box
- Unplug the trunk lamp plug of the original vehicle and plug in the small light cable of our company (Note: after unplugging the plug of the original car, wrap it with adhesive tape, the left and right are the same).
- Fix the controller ground wire in the right trim panel of the trunk
- Remove the trim panel
- Remove the front passenger’s foot trim panel
- Remove the lower trim panel of the storage box
- Power supply position On the right side of the storage box of the passenger side (The negative pole can be connected to the exposed screw on the right side of the trunk, and the screw need not be covered with paint
- Fix the large controller in the right trim panel of the trunk
- Fix the small control box in the tailgate trim panel
- Open a φ20 hole and install the tailgate button
- trunk wiring diagram
- trunk wiring diagram Use a screw to fix the control box inside the right side trim of the trunk, near the right taillight.
The device socket on the tailgate detection wire 5SJ000A21 needs to be plugged back into the controller
Hand button wire Handbuckle switch plug connected to the plug of the original hand buckle button
Model 3 2017-2020 Tailgate Kick Sensor Installation
Manual
Installation Step
- Pry off the clips of the Fender
- Then pull out the harness
- Then connect the plug② of the kick module and stick the 3M glue
- Finally, install the module downward to the appropriate position
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>