milwaukee M12 Fuel Multi Tool Instruction Manual
- June 13, 2024
- Milwaukee
Table of Contents
SERVICE PARTS LIST
BULLETIN NO.
54-22-2406
M12 Fuel Multi Tool
SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS
M12 FUEL MULTI-TOOL
CATALOG NO. 2526-20| STARTING
SERIAL NO.
L31B
REVISED BULLETIN
54-22-2405| DATE
Nov. 2022
---|---
WIRING INSTRUCTION
- = Part number change from previous service parts list.
| FIG. | PART NO. | DESCRIPTION OF PART | NO. REQ. |
|---|---|---|---|
| 2 | 42-70-0480 | Spring Clip | 1 |
| 3 | ————— | M3 x 35mm PWH T-10 Machine Screw | 3 |
| 4 | ————— | Motor End Plate | 1 |
| 5 | 45-30-0047 | Rubber Slug | 3 |
| 6 | 02-04-0568 | Ball Bearing | 1 |
| 25 | 42-70-0510 | Quick Release Clip | 1 |
| 26 | 05-78-0105 | M4 x 10mm Pan Hd. Taptite T-20 Screw | 1 |
| 27 | 05-78-1010 | M3.5 x 12mm Pan Hd. T-10 Machine Screw | 4 |
| 34 | 06-82-2395 | M2.6 x 10mm Pan Hd. ST T-8 Screw | 5 |
| 36 | 06-82-1080 | M3 x 14mm Pan Hd. ST T-10 Screw | 6 |
| 37 | 45-72-0140 | Switch Slide | 1 |
| 46 | 34-40-0431 | O-Ring | 1 |
| 47 | 06-75-1015 | Blade Fastener | 1 |
| 50 | 48-03-2526 | Adapter (Accessory-Sold Separately) | 1 |
| 53 | 49-90-2430 | Depth Stop (Accessory-Sold Separately) | 1 |
| 55 | 49-90-2420 | Dust Extractor (Accessory-Sold Separately) | 1 |
| 57 | 42-55-2526 | Lunchbox Contractor Bag | 1 |
| 58 | 12/20/2531 | Service Nameplate | 1 |
| 59 | 31-44-0249 | Housing Kit | 1 |
| 60 | 14-20-0192 | Electronics Assembly | 1 |
| 61 | 14-46-2526 | Motor End Plate Kit | 1 |
| 62 | ————— | Left Housing Kit with Cushions | 1 |
| 63 | ————— | Right Housing Kit with Cushions | 1 |
| 64 | 14-50-2526 | Motor Assembly | 1 |
| 65 | 14-29-2526 | Gearcase Assembly | 1 |
| 80 | 05-88-1015 | M2.5 x 6mm Pan Hd. Phillips Mach. | 1 |
| 81 | 45-88-0232 | ScrewFlat Washer | 1 |
LUBRICATION:
= Type ‘J’ Grease (1 lb. can), 49-08-4220
= 277 Red Loctite, 44-22-0050
- = Fill back cavity of Gearcase (65) with approx. 3.5 grams of grease.
- = Place a few drops of thread locking sealant to threads of motor end plate screws (3).
- = Place a few drops of thread locking sealant to threads of rear armature screw (80).
- = Place a few drops of thread locking sealant to threads of gearcase screws (27).
AS AN AID TO REASSEMBLY, TAKE NOTICE OF WIRE ROUTING AND POSITION IN WIRE
GUIDES AND TRAPS WHILE DISMANTLING TOOL.
BE SURE THAT ALL COMPONENTS OF THE ELECTRONICS KIT ARE SEATED FIRMLY AND
SQUARELY IN THE HANDLE RECESSES.
AVOID PINCHED WIRES, BE SURE THAT ALL WIRES AND SLEEVES ARE PRESSED COMPLETELY
DOWN IN WIRE GUIDES AND TRAPS.
PRIOR TO SECURING THE HANDLE COVER ONTO THE HANDLE SUPPORT, BE SURE THAT THERE
ARE NO INTERFERENCES.
BEFORE INSTALLING THE BATTERY, CHECK FOR PROPER FUNCTIONALITY OF SHUTTLE AND
TRIGGERS.
INSTALL BATTERY AND DEPRESS SWITCH TRIGGER TO ASSURE TOOL IS OPERATING
PROPERLY.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>