ViewSonic VPC33 Touch Displays Touch Screen PC Modules User Guide

: June 13, 2024
: Viewsonic

Table of Contents

VPC33 Touch Displays Touch Screen PC Modules
Introduction
Product Overview
Initial Setup
Making Connections
Using the Device
Appendix
Regulatory and Service Information
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

VPC33 Touch Displays Touch
Screen PC Modules
User Guide
VPC33
VPC35
VPC37
Model No. VS19693
P/N: VPC33 | VPC35 | VPC37

VPC33 Touch Displays Touch Screen PC Modules

IMPORTANT : Please read this User Guide to obtain important information on installing and using your product in a safe manner, as well as registering your product for future service. Warranty information contained in this User Guide will describe your limited coverage from ViewSonic® Corporation, which is also found on our web site at http://www.viewsonic.com in English, or in specific languages using the Regional selection box of our website.

Thank you for choosing ViewSonic®
As a world-leading provider of visual solutions, ViewSonic® is dedicated to exceeding the world’s expectations for technological evolution, innovation, and simplicity.
At ViewSonic®, we believe that our products have the potential to make a positive impact in the world, and we are confident that the ViewSonic® product you have chosen will serve you well.
Once again, thank you for choosing ViewSonic®!

Introduction

Package Contents

ViewSonic VPC33 Touch Displays Touch Screen PC Modules - Package
Contents

NOTE:
If anything is missing or damaged, please contact your local reseller for more information.

Product Overview

ViewSonic VPC33 Touch Displays Touch Screen PC Modules -
Overview

Number	Item	Description
1	****	**** Security lock
2	Antenna	Wi-Fi antenna interface
3	****	Standard RJ45 (10M/100M/1G) internet connection port

Initial Setup

Installing the VPC33/VPC35/VPC37

Remove the slot-in PC cover of the display.
Carefully insert the VPC33/VPC35/VPC37 into the PC slot of the display.
Secure the VPC33/VPC35/VPC37 to the display with the two (2) screws.
NOTE : Please note that the two (2) antennas must be installed on the VPC33/ VPC35/VPC37.

Making Connections

Network Connection
To connect to the Internet or a network, connect one end of a RJ45 cable to the RJ45 ( ) port of the VPC33/VPC35/VPC37, then connect the other end to your network. ViewSonic VPC33 Touch Displays Touch Screen PC Modules -
port USB Connection

USB peripherals such as keyboards, mice, storage devices, etc. can be connected to the VPC33/VPC35/VPC37’s USB ports. ViewSonic VPC33 Touch
Displays Touch Screen PC Modules - USB Connection

Using the Device

Selecting an Input Source
IFP Series

ViewSonic VPC33 Touch Displays Touch Screen PC Modules - IFP
Series

To select an input source:

Press INPUT/ on the remote control, press the setting button on the front panel, or press the Settings icon from the toolbar to display the Input Settings menu.
Press ▼/▲/◄/► on the remote control to select the PC source.
Press OK/ENTER on the remote control, or touch the input source directly.
Press EPG/BACK/ on the remote control, or touch a blank area outside of the menu to exit.
NOTE: The above image is for reference only and is subject to change without notice.

CDE Series

To select an input source:

Press INPUT/ on the remote control.
Press ▼/▲ on the remote control to select the PC source.
Press OK/ENTER on the remote control.
Press EPG/BACK/ on the remote control to exit.
NOTE: The above image is for reference only and is subject to change without notice.

Appendix

Specifications

Category	Item	Specifications
I/O	Ports	1 x LAN

1 x Display Port 1 x HDMI
4 x USB 3.0
1 x USB type C 1 x Earphone
1 x Microphone
Physical| Dimensions (mm)| 180 x 119 x 30 mm
Dimensions (in.)| 7.09″ x 4.69″ x 1.18″
Weight (kg)| 0.6 kg
Weight (lbs.)| 1.32 lbs.
Operating Conditions| Altitude| 03,048 M (10,000 ft.)
Humidity| 10% — 90% (non-condensing)
Temperature| -5°C — 40°C (23°F — 104°F)
Storage Conditions| Altitude| 012,192 m (40,000 ft.)
Humidity| 10% — 90% (non-condensing)
Temperature| -20°C — 70°C (-4°F — 158°F)
Power| Voltage| 12-19V DC
Consumption| 96W
Wi-Fi Module| Form Factor| Wi-Fi 6 (IEEE 802.11 a/b/g/n/ac/ax WiFi 2T/2R+)
Bluetooth 5.2 (V2.1/4.2/5.2 USB2.0/3.0 Module)
Frequency Range and
Output Power (Max.)| •2402 to 2480 MHz(BT) (5.5dBm)
•2402 to 2480 MHz(LE) (3.73 dBm)
•2412 to 2472 MHz (17.41 dBm) (14.38dbm)
•5150 to 5250 MHz (18.94 dBm) (13.25dbm)
•5250 to 5350 MHz (18.94 dBm) (13.25dbm)
•5470 to 5725 MHz (18.94 dBm) (12.75dbm)

Regulatory and Service Information

Compliance Information
This section addresses all connected requirements and statements regarding regulations. Confirmed corresponding applications shall refer to nameplate labels and relevant markings on the unit.
FCC Compliance Statement
This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Warning : You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
Industry Canada Statement
FCC ID: PD9AX200NG
IC ID: 1000M-AX200NG
CAN ICES-003(B) / NMB-003(B)

Conformity for European Countries

The device complies with the EMC Directive 2014/30/EU, Low Voltage Directive 2014/35/EU and Radio Equipment Directive 2014/53/EU.
https://www.viewsonicglobal.com/public/products_download/safety_compliance/acc/VS19693_CE_DoC.pdf

The following information is only for EU-member states:
The mark shown to the right is in compliance with the Waste Electrical and Electronic Equipment Directive 2012/19/EU (WEEE). The mark indicates the requirement NOT to dispose of the equipment as unsorted municipal waste, but use the return and ollection systems according to local law.

Declaration of RoHS2 Compliance
This product has been designed and manufactured in compliance with Directive 2011/65/EU of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS2 Directive) and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below:

Substance| Proposed Maximum Concentration| Actual Concentration
---|---|---
Lead (Pb)| 0.1%| < 0.1%
Mercury (Hg)| 0.1%| < 0.1%
Cadmium (Cd)| 0.01%| < 0.01%
Hexavalent Chromium (Cr6⁺)| 0.1%| < 0.1%
Polybrominated biphenyls (PBB)| 0.1%| < 0.1%
Polybrominated diphenyl ethers (PBDE)| 0.1%| < 0.1%
Bis(2-ethylhexyl) phthalate (DEHP)| 0.1%| < 0.1%
Butyl benzyl phthalate (BBP)| 0.1%| < 0.1%
Dibutyl phthalate (DBP)| 0.1%| < 0.1%
Diisobutyl phthalate (DIBP)| 0.1%| < 0.1%

Certain components of products as stated above are exempted under the Annex III of the RoHS2 Directives as noted below:

Copper alloy containing up to 4% lead by weight.
Lead in high melting temperature type solders (i.e. lead-based alloys containing 85% by weight or more lead).
Electrical and electronic components containing lead in a glass or ceramic other than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or ceramic matrix compound.
Lead in dielectric ceramic in capacitors for a rated voltage of 125V AC or 250V DC or higher.

Indian Restriction of Hazardous Substances
Restriction on Hazardous Substances statement (India). This product complies with the “India E-waste Rule 2011” and prohibits use of lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers in concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, except for the exemptions set in Schedule 2 of the Rule.
Product Disposal at End of Product Life
ViewSonic® respects the environment and is committed to working and living green. Thank you for being part of Smarter, Greener Computing. Please visit the ViewSonic® website to learn more.

USA & Canada:
https://www.viewsonic.com/us/go-green-with-viewsonic
Europe:
https://www.viewsonic.com/eu/go-green-with-viewsonic
Taiwan:
https://recycle.epa.gov.tw/

Copyright Information

Copyright© ViewSonic® Corporation, 2023. All rights reserved.
Macintosh and Power Macintosh are registered trademarks of Apple Inc.
Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft Corporation in the United States and other countries.
ViewSonic®, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks of ViewSonic® Corporation.
VESA is a registered trademark of the Video Electronics Standards Association.
DPMS, DisplayPort, and DDC are trademarks of VESA.
Disclaimer: ViewSonic® Corporation shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from furnishing this material, or the performance or use of this product.
In the interest of continuing product improvement, ViewSonic® Corporation reserves the right to change product specifications without notice. Information in this document may change without notice.
No part of this document may be copied, reproduced, or transmitted by any means, for any purpose without prior written permission from ViewSonic® Corporation.

Customer Service

For technical support or product service, see the table below or contact your reseller.
NOTE : You will need the product’s serial number.

Americas

United States www.viewsonic.com/us
Latin America www.viewsonic.com/la