CURT 13531 Trailer Hitch Instruction Manual
- June 13, 2024
- Curt
Table of Contents
**CURT 13531 Trailer Hitch Instruction Manual
**
Level of Difficulty
Easy
Installation difficulty levels are based on time and effort involved and may vary depending on the installer level of expertise, condition of the vehicle and proper tools and equipment.
Weight Carrying Capacity
Gross trailer weight (GTW): 2,000 lbs.
Tongue weight (TW): 200 lbs.
Parts List
| Item | Qty | Description |
|---|---|---|
| 1 | 4 | Hex head cap screw, M10 x 1.25″ |
| 2 | 4 | Conical washer, 7/16″ |
| 3 | 2 | Spacer |
Tools Required
| Socket, 10mm | Flathead screwdriver |
|---|---|
| Socket, 13mm | Paint marker |
| Socket, 15mm | Utility knife / aviation shears |
| Socket, 17mm | Torque wrench |
* For a tools reference guide visit
curtmfg.com/trailer-hitch-installation
WARNING
Never exceed the vehicle manufacturer’s recommended towing capacity.
Product Photo
NOTICE
Visit www.curtmfg.com for a full-color copy of this instruction manual, as well as helpful videos, guides and much more!
Before you begin installation, read all instructions thoroughly.
Proper tools will improve the quality of installation and reduce the time
required.
This installation requires:
- Trim or removal of underbody panel
- Loosening of the canister
- Lowering of the exhaust
Periodic inspection of the trailer hitch should be performed to ensure all mounting hardware remains tight and structural components are secure.
To help prevent damage to the product or vehicle, refer to the specified torque specifications when securing hardware during the installation process.
SAFETY INSTRUCTIONS
Safety glasses should be worn at all times while installing this product.
Product Registration and Warranty
CURT stands behind our products with industry-leading warranties. To get copies of the product warranties, register your purchase or provide feedback, visit: warranty.curtgroup.com/surveys
ASSEMBLY
Parts List
| Item | Qty | Description |
|---|---|---|
| 1 | 4 | Hex head cap screw, M10 x 1.25″ |
| 2 | 4 | Conical washer, 7/16″ |
| 3 | 2 | Spacer |
CONICAL TOOTHED WASHER ORIENTATION
Step 1
If present, remove the underbody panel that secures to the bumper cover by
removing seven push pins with a screw driver, six nuts with a 10mm socket and
loosen the two plastic zip nuts in the center of the panel with a 15mm socket.
Step 2
On gas models, lower the canister on the driver side as well as the exhaust by removing the two nuts and one bolt securing them using a 13mm socket. Unhook the two muffler hangers. Support both canister and exhasut while installing the hitch.
Step 3
Trim the bumper cover tab off in the center of the vehicle.
Step 4
Raise the hitch into position and loosely install the supplied hex head cap
screws (#1) and conical tooth washers (#2).
Note: On some models there will be a gap between the side plates and
frame. Use the supplied spacers as needed between the frame and side plates to
fill the gap.
Step 5
Torque all 10mm fasteners to 48 ft-lbs.
Step 6
If lowered in step 2, reinstall the canister on the driver side and raise the exhaust back into position. Rehook the hangers.
Step 7
If removed in step 1, trim the underbody panel as shown and reinstall
Final Installed Image
TOWING BASICS & SAFETY INFORMATION
For information on safely towing your trailer, visit curtmfg.com /understanding-towing.
CURTMFG.COM
PRODUCT SUPPORT: 877.287.8634 • 13531-INS-RA • 11/09/2022 • ECN10232 •
PAGE 5
References
- CURT: Trailer Hitches - Trailer Wiring - 5th Wheel - Gooseneck
- 8 Easy Steps - Trailer Hitch Installation How-To
- Towing Guide, How-tos, References & Glossary
- CURT: Trailer Hitches - Trailer Wiring - 5th Wheel - Gooseneck
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>