GPad Joyride V2.4 Most Universal Scooter Out There User Manual

www.gpadscooters.com
GPad® Joyride V2.4
User Manual

IMPORTANT! Read carefully and keep for future reference.

Package Contents

Check that all of the items pictured above are included in your scooters package. If any are missing please contact your dealer.

Diagram

Dashboard

Settings – to access or exit the settings hold the + and – buttons down together for 3 seconds.
Use the middle button to navigate between the settings and the + and – buttons to change the value of the setting.
P01: Battery voltage setting. This value must be 36 for Joyride Eco and 48 for Joyride.
P02: Change between units. 0: km/h, 1: mph
P04: Automatic power off. Range 1-60 minutes. 0 means no automatic power off.
P06: Wheel diameter in inches. This needs to be set to 10.
P07: Number of magnets in the motor. This needs to be set to 30.
P09: Zero start setting. 0: the throttle is active from standstill, 1: you need to push the scooter up to
3 km/h for the throttle to activate.
P12: Starting acceleration. 0 is the weakest acceleration, 5 is the strongest.
P15: Motor power in percentage (1-100%).
P16: Cruise control. 0: cruse control is off, 1: cruise control is on. If the cruise control is on, then it will activate automatically after you maintain the same speed for 10 seconds. To disengage it press either the brake or the throttle.

Folding

Turn your scooter off before folding. To fold or unfold the scooter pull back on the quick release lever located near the folding mechanism. If you have difficulty moving the quick release lever push the steering column forwards as you pull  the lever.

Once the scooter is in the desired position (folded or unfolded) press down on the quick release lever marked as A.
Make sure that the locking pin marked as B locates securely into its socket.
DO NOT ride the scooter if the folding mechanism is damaged or if the locking pin is not properly secured in its socket.

Charging

Before charging, turn off the scooter. First insert the charger into an electrical outlet and then connect it to the scooter.
Charging from 0%-100% takes about 7 hours (about 5.5 hours with Joyride Eco).
We recommend recharging the scooter at regular room temperature.
WARNING!
DO NOT charge the scooter if the charge port or power cord is wet.
DO NOT charge or use your battery if it is damaged or see trace of water.
Close the charging port cover when not charging the scooter.

How to Ride your Electric Scooter

1. Before riding make sure, that the steering system is correctly adjusted and that all connection elements (such as the folding mechanism) are correctly tightened and not damaged and that the brakes and wheels are in good condition.

2. Make sure to fully charge your new GPad® Joyride before your first ride.

3. Fold your scooter into its riding position following the instructions in chapter 4. After that, unfold the handlebars by lifting them up until they lock into place. To fold them back down again simply pull back the handlebar folding sleeve.

4. Turn the scooter on following the instructions in chapter 3.

5. Make sure that the kickstand is folded up into the riding position.

6. Grab the handlebar with both hands and with one foot placed on the platform, push off with the other to start moving.

7. Once moving, use your right thumb to press the throttle to accelerate.

8. To decelerate use your left hand to pull the brake lever towards yourself.
   WARNING! When braking hard, you risk losing traction which can cause serious injury. Always look ahead for potential hazards and ride at moderate speed. Braking distances increase with wet weather.

9. Use the handlebar to to turn by turning it slightly and shifting your body towards the direction you want to turn

10. To turn the scooter off again hold down the power button for about 3 seconds.

11. When parking the scooter use your foot to fold down the kickstand located at the rear of the scooter, then tilt the scooter towards the side with the kickstand.
    When riding the scooter wear a helmet and other protective gear (knee, wrist and elbow protection) to reduce the risk of injury.
    Always ware shoes (high heels not recommended) when riding your scooter. Never ride barefoot.

Maintenance

Regularly check the tightening of the various bolted elements, in particular the wheel axles, the folding system, the steering system and the brakes.
Cleaning – To clean the scooter use a damp soft cloth. A brush can be used to clean off dirt that is harder to remove. DO NOT use alcohol or other solvents to clean the scooter. DO NOT clean the scooter with a pressure washer, hose or with splashing water. The scooter is not waterproof. Any water damage voids the warranty.
Tire Pressure – inflate both tires to 3 bar (40psi). Check for tire pressure after receiving the scooter from the dealer, and regularly afterwards. If one of the tires is damaged or won’t hold air then stop riding the scooter.
Tightening the folding mechanism – To tighten the folding system, first release the screw A on figure 3, on both sides. Turn clockwise the screw B on figure 3, located at the front end. Do this on both sides. Finally retighten the screws A on figure 3.

Tightening the handlebar folding mechanism – To tighten the handlebar, open the sleeves and fold the handlebar. Inside you find a 3mm hex screw (see figure 4).
Using the hex key, gradually turn the screw counterclockwise. Check every little while if the handlebar is tight enough. If the handlebar does not lock into the driving position turn the hex screw to the opposite direction.
Storage – Turn the scooter off and disconnect the charger during storage. Make sure that the battery is about 50-60% charged. You should check how much charge the battery has left at least once a month. If the battery charge has decreased, charge the scooter until the battery has about 50-60% charge. Store the scooter in a dry room at about 15 to 25°C.
WARNING! As with any mechanical component, a vehicle is subject to high stresses and wear. The various materials and components may react differently to ware and fatigue. If the expected service life for a component has been exceeded, it may break suddenly, therefore risking causing injuries to the user.
Cracks, scratches and discoloration in the areas subject to high stresses indicate that the component has exceeded its service life and should be replaced.

Specifications

absorber
Motor Nominal Power| 500 W| 350 W| 500 W
Tires| Pneumatic 10×2.25| Pneumatic 10×2.25| Pneumatic 10×2.25
Required height of the user| 120 – 200 cm| 120 – 200 cm| 120 -200 cm
Recommended age| 14+| 14+| 14+
Nominal Battery Voltage| 48 VDC| 36 VDC| 48 VDC
Nominal Battery Capacity| 624 Wh| 360 Wh| 840 Wh
Charging Voltage| 54.6 VDC| 42 VDC| 54.6 VDC
Charging Current| 2 A| 2 A| 3 A
Charging Time| 7 h| 5.5 h| 6 h
Working Temperature| -1 – +40 °C| -1 – +40 °C| -1 – +40 °C
Product Net Weight| 16 kg| 15.5kg| 17.5 kg

*Depends on the rider’s weight, riding style, speed, terrain, temperature and wind.

Warnings

WARNING
Failure to follow these instructions might lead to serious injury.

DO NOT ride the scooter in rain or through puddles and DO NOT get it wet. Water damage is voids the warranty.
DO NOT ride the scooter if it has been damaged.
DO NOT drive up or down stairs or jump off or over obstacles.
DO NOT store your scooter at temperatures of less than 15°C or in wet conditions.
DO NOT touch the motor or the brake disc after riding, it can get hot.
DO NOT rest your foot on the rear fender.
DO NOT use your mobile phone whilst operating the scooter.
DO NOT ride your scooter one handed or take both your hands off the handlebar.
DO NOT carry any passengers. The scooter is designed to carry one person only.
DO NOT exceed the 120kg weight limit of the scooter.
DO NOT ride the scooter if you are pregnant.
DO NOT ride the scooter whilst under the influence of alcohol or drugs.
DO NOT attach heavy or loose items to the handlebar, as this will effect the scooters stability.
DO NOT modify your scooter or use accessories or additional items not approved by the manufacturer.
This vehicle is not intended for acrobatic use.
This vehicle is not intended for commercial or rental use.
Familiarise yourself with local traffic regulations and other legislation applicable to electric scooters.

Contact

GPad® scooters are designed and manufactured by: Fortunati Group EU www.gpadscooters.com
Distributor in Europe: Fortunati Distribution LTD
Telliskivi 57D, 10412, Tallinn, Estonia
Tel: +372 56 808 138
E-mail: gpad@fortunati.eu
Tel Service: +372 600 40 99
E-mail Service: service@gpad.ee
www.fortunati.eu

References

• Fortunati – Personal electric mobility
• Gpad

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>