Mustang Seats F6B 2013 Honda Gold Wing One Piece Seat Instructions
- June 13, 2024
- Mustang Seats
Table of Contents
Mustang Seats F6B 2013 Honda Gold Wing One Piece Seat
Product Information
The product being discussed is a one-piece seat designed for the Honda Gold Wing F6B 2013 motorcycle. The seat is manufactured by Mustang and features a marine-grade fiberglass baseplate. The baseplate replaces the stock one-piece seat and includes rubber bumpers to prevent the seat from touching the frame and fender. The package includes 2 6mm x 16mm button-head Allen bolts for installation. Part Numbers: 76840, 76841
Product Usage Instructions
Removal of Stock Seat:
- Using a 6mm Allen wrench, remove the two Allen bolts from the left passenger grab rail. These bolts will be used to install your Mustang seat.
- Repeat the procedure to remove the right grab rail.
- Locate and remove the two 6mm hex bolts which were covered by the hand rail with an 8mm hex wrench or socket. These will not be used to install your Mustang seat.
- Lift the rear of the stock seat, pull up and back to remove the seat from the frame.
Installation of Mustang Seat:
- Install the provided 6mm x 16mm Allen bolts through the fender and into the frame. Ensure these bolts are tightened. Place the Mustang seat on the frame and slide it forward to engage the nose bracket with the frame receiver.
- Insert one long stock Allen bolt through the left grab rail’s forward mounting hole, through the Mustang seat’s forward mount, and thread it into the frame. Keep this bolt somewhat loose. If the bolt is difficult to thread, adjust the alignment of the Mustang seat’s mounting inserts with the frame hole using a blunt tool such as a Phillips screwdriver.
- Align the rear grab rail holes with the rear mounts in the side of the Mustang seat. Ensure the saddlebag release stem is in the grab rail’s release mechanism, and thread one short stock Allen bolt through as before.
- Repeat the procedure with the right grab rail.
- Slowly tighten the four Allen bolts evenly, working back and forth from the left to the right side, until all bolts are tightened. Enjoy the comfort and custom look of your new Mustang seat! If you need further assistance, please contact Mustang at: Phone: 800-243-1392 or 413-668-1190 (Monday through Friday, 9:00 – 5:30 Eastern)
Email: questions@mustangseats.com
Website: www.mustangseats.com For care and maintenance instructions, please visit their website under Support.
Hardware included : 2 6mm x 16mm button-head Allen bolts
Tools needed: 6mm Allen wrench 8mm hex wrench or socket
Baseplate Features
The one-piece, marine-grade fiberglass baseplate directly replaces the stock one-piece seat. Rubber bumpers are positioned to prevent the seat from touching the frame and fender.
Removal of Stock Seat
- Using a 6mm Allen wrench, remove the two Allen bolts from the left passenger grab rail. These bolts will be used to install your Mustang seat.(fig. 1) Note – the rail is quite heavy; use caution to prevent it from dropping onto the motorcycle or yourself
- Repeat procedure to remove the right grab rail.
- Locate and remove the two 6mm hex bolts which were covered by the hand rail with an 8mm hex wrench or socket. These will not be used to install your Mustang seat. (fig. 2)
- Lift the rear of the stock seat, pull up and back to remove seat from frame.
Installation of Mustang Seat
- Install the provided 6mm x 16mm Allen bolts through the fender and into the frame. Be sure these bolts are tightened.
- lace the Mustang seat on frame and slide forward to engage the nose bracket with the frame receiver.
- Insert one long stock Allen bolt through the left grab rail’s forward mounting hole, through the Mustang seat’s forward mount, and thread it into the frame. Keep this bolt somewhat loose. (fig. 3 No te – if the bolt is difficult to thread, adjust the alignment of the Mustang seat’s mounting inserts with the frame hole using a blunt tool such as a Phillips screwdriver.
- Align the rear grab rail holes with the rear mounts in the side of the Mustang seat.
- Be sure the saddlebag release stem is in the grab rail’s release mechanism, and thread one short stock Allen bolt through as beforeRepeat procedure with the right grab rail.
- Slowly tighten the four Allen bolts evenly, working back and forth from the Fig 4 left to the right side, until all bolts are tightened. (fig. 4)
Enjoy the comfort and custom look of your new Mustang seat
These steps are guidelines to help you install your new Mustang product. If you need further assistance, please call us at 800-243-1392 or 413-668-1190, Monday through Friday 9:00 – 5:30 Eastern or send an e-mail to questions@mustangseats.com or visit our website at www.mustangseats.com. For care and maintenance of our seats, please go to our website under “Support”. Refers to part numbers: 76840, 76841