GRACO 244113 HVLP Turbine Guns Instruction Manual
- June 13, 2024
- Graco
Table of Contents
GRACO 244113 HVLP Turbine Guns Instruction Manual
Symbol
Warning Symbol
⚠ WARNING
This symbol alerts you to the possibility of serious injury or death if you do
not follow instructions.
Caution Symbol
⚠ CAUTION
This symbol alerts you to the possibility of damage to or destruction of
equipment if you do not follow instructions.
You will need:
Cleaning fluids: a compatible solvent; water based paint also requires soap
and water.
Suggested proper clothing:
- Safety glasses
- Sturdy boots or shoes
- Respirator
- Gloves
Component Identification
PRESSURE RELIEF Follow this procedure when cleaning, repairing or shutting down sprayer
TIP SELECTION
Installing the Fluid Set
⚠ CAUTION
Trigger the gun whenever you tighten or remove the nozzle. This keeps the
needle seat away from the nozzle seating surface and prevents the seat from
being scratched.
- Use your hand to loosen and remove the air cap retaining ring and air cap housing.
- Test spray pattern and atomization while holding gun about 6 to inches (150 to 200 mm) from test piece.
- While triggering the gun, use your hand to loosen and remove the nozzle.
- Use your hand to loosen and remove the fluid knob assembly and compression ring from the back of the gun and remove the old needle.
- Insert the needle assembly in the back of the gun. Reassemble nozzle, air cap housing and air cap retaining ring. Hand tighten.
Note: Nozzle should always have an oring (A).
Setup
6. Connect air hose to gun and turbine.
7. For cup gun, turn fluid control out until trigger movement is not
restricted.
Caution: Turning knob too far will remove it. For remote pressure pot, hold
gun parallel to floor and adjust fluid pressure to an 8 to 10 inch (203 to 254
mm) fluid stream.
NOTE: Heavier fluids or longer fluid hoses require greater pressures.
8. Reduce and test catalyze all paint to manufacturer’s specifications.
S If no reduction instructions are given, mix the fluid thoroughly, then
gradually mix in reducer. To check the consistency of the fluid. Remove the
stir stick from the thinned paint. When the paint streaming off the stick
breaks into droplets, the first few drops should be one second apart. S To
compensate for faster drying time of turbine systems, use a reducer one step
slower than used for conventional air spray systems.
9. Remove cup. Fill 3/4 full. DO NOT OVERFILL. Reattach and latch cup.
10. Plug turbine power cord into a grounded outlet.
SPRAY
11. Open air control valve. 12. Turn turbine on. Wait several minutes prior
to spraying to allow warmup time.
13. Turn air cap to obtain desired direction. 14. Lock air cap with retaining
ring.
15. Select spray pattern by adjusting the fluid knob and pattern selection knob. The air control adjusts the TOTAL air to the pattern and gun.
Note: If fluid is not atomizing properly, fluid may need to be thinned further, or a different tip size may be used.
16. Hold gun perpendicular, 68 inches from surface. Move gun first, then pull gun trigger to spray.
17. To control overspray, reduce air flow or reduce fluid volume.
Note: If fluid is not atomizing properly, fluid may need to be thinned
further, or a different tip size may be used.
Swivel Tube Adjustment
The adjustable swivel tube allows the HVLPTurbine Gun to be held in any
position why spraying. To adjust the position of the tube in the cup:
- Loosen the nut (A) with a wrench (42).
- Rotate the cup to the desired spray position.
- Retighten the nut (A) with a wrench (42).
Shutdown
Cleaning the Spray Gun (solvent/oil-based)
Shutdown (water base)
Parts for HVLP-Turbine Gun
Model Nos. 244113, 244115, 244117, 244118
Technical Data
Maximum inlet fluid pressure . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . 50 psi (0.35 MPa, 3.5
bar)
Maximum inlet air pressure . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 psi (0.07 MPa, .7
bar)
Air inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . Quick-disconnect
Fluid inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . 3/8 nps
Sound levels per ISO 3744
Sound power level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . less than
65.0 dB(A)
Sound pressure level . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . less than 65.0
dB(A)
Wetted parts
Bare spray gun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . stainless steel,
aluminum
Spray gun cups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . aluminum,
polyethylene
2-quart accessory remote pressure pot . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . aluminum, polyethylene
21/2-gallon accessory remote pressure pot . . . . . . . . . . steel with
solvent-resistant finish, EPDM gasket (standard)
Notes
Graco Standard Warranty
Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of nonGraco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.
Graco makes no warranty, and disclaims all implied warranties of merchantability and fitness for a particular purpose in connection with accessories, equipment, materials or components sold but not manufactured by Graco. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English.
ADDITIONAL WARRANTY COVERAGE
Graco does provide extended warranty and wear warranty for products described
in the “Graco Contractor Equipment Warranty Program”.
Graco Phone Number
TO PLACE AN ORDER, contact your Graco distributor, or call this number to identify the distributor closest to you: 18006902894 Toll Free
All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice. MM 309317
Graco Headquarters: Minneapolis International Offices: Belgium, China, Japan,
Korea GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 554401441
www.graco.com 2/2002 Rev. 5/2006
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>