VOLT VSPL-1045-BBZ-R1 Solar Integrated LED Path Light Instruction Manual
- June 13, 2024
- VOLT
Table of Contents
INSTALLATION INSTRUCTIONS
VSPL-1045-BBZ-R1 Solar Integrated LED Path Light
VOLT® Low Voltage Landscape Lighting
VOLT ® Solar Integrated LED Path Light
VSPL-1045-BBZ-R1 & VSPL-1045-PBK-R1
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-
Sun 10am – 6pm (EST)
Specifications and product details subject to change without notice.
© Copyright 2023, VOLT® Lighting, Lutz FL USA 33549
All rights reserved.
customersupport@voltlighting.com •
813.978.3700
**** Important: Please Read Before Installation
This luminaire is intended for installation in accordance with local codes and
the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
Please note that these solar fixtures are equipped with built-in photocells,
so they will not turn on until it is dark enough. These fixtures will also
require plenty of sunlight to function properly. It’s best to have the fixture
in an area where the sun will get to it at all times throughout the day and
where no ambient lighting will affect the photocell at night. If your fixture
is not functioning at night, be sure that the on/off button has been engaged.
See step one for details.
**** Important Safety Instructions
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS Lighted lamp
is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
- Lamp gets HOT quickly!
- Do not touch the hot lens, guard or enclosure.
- Keep lamp away from materials that may burn.
- Do not touch lamp at any time. Use a soft cloth. Oil from skin may damage lamp.
- Do not operate the luminaire fitting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS
Package Contents
A. (1) Fixture Body
B. (1) Battery
Parts Required
A. (1) Mounting Accessory
B. (1) Riser
Product Dimensions
-
Remove Battery Compartment Cover
Using a screwdriver, remove the battery compartment cover from the fixture body. -
Install Battery
Insert the battery into the battery compartment. -
Reinstall Battery Compartment Cover
Place the battery compartment cover back onto the fixture body and secure with the previously removed screws. -
Test Solar Light
Slide the ON/OFF switch of the fixture to the “ON” position.
Cover solar panels completely by using black materials. The fixture will light up when the solar panel is covered and turn back off when it is uncovered.
Now you can proceed to next steps of installations knowing the fixture is in ON mode. -
Install Riser
Thread the riser onto the fixture and hand tighten until snug. -
Install Stake
Determine the desired location for mounting the stake mount. Hammer the stake into the ground until flange of stake is flush to grade. To avoid damage to the stake, place a board on top of the stake while hammering.
Note: If the ground is hard and the stake is difficult to install, make a crosscut in the ground using a flat shovel. -
Install Stake
Thread the riser on to the stake and hand tighten until snug.
www.voltlighting.com
customersupport@voltlighting.com •
813.978.3700
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-
Sun 10am – 6pm (EST)
www.voltlighting.com
Specifications and product details subject to change without notice.
© Copyright 2023, VOLT® Lighting, Lutz FL USA 33549
All rights reserved.
customersupport@voltlighting.com •
813.978.3700
IS-VSPL-1045-BBZ-R1-ver1.pdf