ds18 SWLDC1.2 Long Distance and Steering Wheel Sound audio Control Combo User Manual

SWLDC1.2 Long Distance and Steering Wheel Sound audio Control Combo
User Manual

SWIDC1.2 COMBO
SOUND CONTROL

PRESENTATION

The SWLDC1.2 combo steering wheel control lets you control the main functions of the player through two transmitters and one receiver. Transmitter (A) remote control with a range of 1200 meters in an open area (aimed), the transmitter (B) can be easily attached to the steering wheel of the car, allowing sound control safely while driving.

OPERATION

Transmitter Unit: Whenever an o button is pressed, an RF (radio frequency) signal will be transmitted to the receiving unit.
Receiving Unit: The “led action” will light up indicating the presence of the received signal, and will transmit the code corresponding to the key pressed in IR (infrared). The receiver can operate with two transmitters by performing steps 1 and 2 of “CODING THE CONTROL” for the new transmitter.

NOTES IMPORTANT

1. The control unit will not function if the coding procedure is not performed.
2. To avoid interference, install the receiver in a location where the antenna is near the panel and at least 50cm away from the car alarm receiver.

BASIC INDICATIONS AND COMMANDS

1. Controls Volume
2. Change Track
3. Change Folder
4. Play / Pause
5. Power / Function (switches to aux, cd, USB, radio, etc.)

01 – Controls volume
02 – Change of track and/or radio station
03 – Pause or mute
04 – Change of function (switches to aux, cd, USB, radio, etc.) pressing with a quick tap, turns off with a long press

01- RF receiver antenna
02- Led action, reception indicator
03- Code IR (see learning mode)
04- Power supply 12v (black white stripe) and GND (black)
05- Infrared transmitter (point to the front of the player)

CODING THE CONTROL

LEARN MODE (Learn the functions of the original control)
Control A:

1. Press the “A” button in Receiving Unit (Indicator 1, Fig. 2), the action led will be steadily on.
2. Press the button of Control A (Indicator 2, Fig. 2), which you wish to record, until the “led action” (indicator 3, Fig. 2) flashes.
3. Point the original control of the player to the code IR input and press the key you want to record (Note 4, Fig. 2) until the action LED blinks rapidly, and then steadily on.
4. Repeat steps 2 and 3 for the other key functions.
5. After completing this process, press the “A” key (Indication 1, Fig. 2) on the receiver or wait 10 seconds to exit the mode.

Control B:

1. press the “A” button in Receiving Unit (Indication 1, Fig. 2), the “led action” will be steadily on.
2. Repeat step 2 and 3 by recording any of the keys recorded on control 1.

MEMORY MODE (The receiver has stored in its memory the codes of the main models of “player” (see the attached table)).
Control A:

1. Press the “M” key (Note 5, Fig. 2), the action led will be steadily lit;
2. Press the keys on control A (Indicator 2, Fig. 2) corresponding to the model of the player, according to the table. Example: If you want to program the SONY CD, you must perform step 1 and then press the keys sequentially, control A. Verify that the led will blink 1 time and then 4 times, indicating that model 14 (Sony) has been programmed.
3. After completing this process, press the “M” key (Indication 5, Figure 2) on the receiver or wait 10 seconds to exit the mode.

Control B: Repeat steps 1 and 2 of memory mode, for the same model of “player” made in control A.

CODE TABLE O1-02 MEMORY MODE

NOTE: Keys that must be pressed simultaneously:

|
---|---

CONTROL INSTALLATION

I- Select the Player model in the control memory (see MEMORY MODE) or learn the code using the original control of the player (see LEARN MODE). These steps are described in the topic CODING THE CONTROL.
II – Position the control in the region where it will be installed (Fig. 03).
III – Clean the whole region where the control will be installed, including the side of the transmitter, with alcohol until it is free of impurities, this procedure must be done carefully to ensure a perfect installation and operation of the control (Fig. 04).
IV – Remove the protective paper from the adhesive part and stick the control in the previously chosen position (Fig. 05).
V – Remove the protector from the velcro adhesive and attach the transmitter behind the steering wheel underneath it (Fig 06).
VI – Loosen the Velcro, remove the remaining protective paper from the adhesive and reattach the Velcro (Fig. 07).

RECOMMENDATIONS AND OBSERVATIONS

1. To avoid interference, install the receiver in a location where the antenna is near the panel and at least 50cm away from the car alarm receiver.
2. For greater reach, the antenna should be kept taut and in a place that is both visual and distant from the car bodywork.
3. Supply the receiver unit with 12V.

TECHNICAL CHARACTERISTICS

Name of transmitter control A| LDC1.2T
Name of transmitter control B| SWC1.2
Transmitter Power supply A| 12V – A23 Battery
Transmitter Power supply B| 3V – CR2032 Battery
Receiver power| 9 to 16Vdc
Operating Frequency| 433.92 MHz
Modulation| ASK

SERVICE WARRANTY

Should your LDC1 2 require service please consult with the dealer from which it was purchased or DS1 8 Local Dealer. Do not attempt to return your LDC1.2 directly to us without first calling for a Return Authorization Number. Units received without an accompanying Return Authorization Number will be processed slower. Additionally, you must include a copy of your purchase receipt from an authorized dealer for consideration of in-warranty service; otherwise, repair charges will apply. Units received without a receipt will be held for 30 days, and all units will be returned to you, unrepaired.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>