iTECHWORLD ITECH2000A Multifunctional Jump Starter User Guide

iTECHWORLD ITECH2000A Multifunctional Jump Starter

INTRODUCTION

The iTECH2000A is a multi-functional jump starter device. The primary function of the iTECH2000A is to jump start your vehicle if it has a flat battery, any petrol vehicle and diesel vehicles up to3L. In order to get the full benefit of the iTECH2000A it is important to read and understand the user guide. In the unfortunate event that you do have a flat battery, correct user operation of the iTECH2000A will ensure a quick fix to the flat battery and will get you out of trouble.

The iTECH2000A’s secondary function is as a battery storage device. The iTECH2000A can be used to charge mobile devices, tablets, cameras, and to run 12v appliances such as a 12v fridge.

GETTING TO KNOW YOUR ITECH2000A

OPERATING INS.TRUC:TIONS

CHAIRG ING YOUR ITECH201100A
You can charge your ITECH2000A one of two ways:

1. Usi11g the supplied 240volt mains charger.
   
   OR

2. 12V car charger into the jack of cigar lighter.
   

• Charging takes 4-5 hours using either charging options.

STARTING YOUR VEHICLE

For the best results, please ensure your iTECH2000A is no  less than 80% charged. If it is below 80% you may not beable to start some vehicles.

• Connect the intelligent jumper leads into your iTECH2000A.

• Connect the + (red clamp) to the + on your vehicle battery.

• Connect the – (black clamp) to the – on your vehicle battery.
  

• Press the small circle button on the hand piece of the intelligent jumper leads. This will initiate a 60 second countdown on the hand piece screen of the intelligent jumper leads.

• Turn your key to start the vehicle before the countdown reaches zero.

• Once the vehicle has started disconnect the intelligent  jumper leads from the battery first and the iTECH2000Asecond.

• If your vehicle does not start, repeat this process.

INTELLIGENT JUMPER LEADS: ERROR MESSAGES

ERR 1: Intelligent Jumper Leads are not making a good enough connection to the vehicle’s battery terminals.
ERR2 : The Intelligent Jumper Leads are short circuited.
ERR3 : Over Voltage – The voltage of the battery is higher than the voltage of the jump starter.
ERR4 : The Jump Starter does not have enough voltage to
start the vehicle – recharge your iTECH2000A.
ERR5 : The temperature of the Jump Starter is too high.
ERR7 : The starting current of the vehicle exceeds 2000CCA.

TURNING YOUR ITECH2000A ON/OFF

The iTECH2000A does not require to be turned on to be used as a jump starter, only when used as a battery bank.
Please note that when your iTECH2000A is switched on it will have a self discharge rate due to the back lit screen and  the wireless charging zone. Always turn your iTECH2000A off before storing.

To turn your iTECH2000A on, press the large red on/off button. The screen will illuminate in blue.

To turn your iTECH2000A off, press and hold the large red on/off button for 5-7 seconds or until the screen turns off.

STATE OF CHARGE INDICATOR

To check the state of charge of your iTECH2000A

• Turn the iTECH2000A on by pressing the large red on/off button.
• The state of charge will be shown as a % on the screen.

USING THE TORCH

To use the torch on the iTECH2000A

• Turn the iTECH2000A on by pressing the large red on/off button.
• Double press the large red on/off button – the torch will turn on.
• Press the large red on/off button again to activate the strobe function.
• Press the large red on/off button again to activate the SOS function.
• Press the large red on/off button again to turn the torch off.

WIRELESS CHARGING

The iTECH2000A is Qi charging ready. You can charge a Qi-enabled  smart device wirelessly from the iTECH2000A
Please check that your smart device is Qi-enabled before using this feature. If your device is not Qi-enabled it will not via the wireless charging zone.

• Turn your iTECH2000A by pressing the large red on/off button.
• Place your Qi-enabled smart device on the wireless charging area.
• The Qi-enabled smart device will now charge.

CHARGING DEVICES

You can either use the provided USB split cable in the kit or the original USB cable that came with the device. Please  note that some devices will require to use the original USB cable that came with the device.

Connect the cable into the iTECH2000A’s USB port.
Connect the device to the cable.

RUNNING A 12V DEVICE

The iTECH2000A is capable of running 12v devices such as a 12v fridge. Please note that not all 12v appliances are supported and some 12v appliances may require an EC5 adapter to operate on the iTECH2000A.
The 12v device must have a 12v male cigarette adapter to operate on the iTECH2000A. Any device which draws over 8a will automatically switch off the iTECH2000A.

• Turn the iTECH2000A on by pressing the large red on/off button.
• Insert the 12v female cigarette socket (provided in the kit) into the 12v/8a out put port.
• Insert the 12v device’s male cigarette plug into the female cigarette socket.
• If the device is compatible it will run via the iTECH2000A.

FREQUENTLY ASKED QUESTIONS

• How do I turn off the iTECH2000A
  Press and hold the large red on/off button for 5-7 seconds.

• How long does the iTECH2000A take to charge
  The iTECH2000A will take 4-5 hours to charge depending on the charging method, 12v or 240v.

• How many time can I jump start my vehicle from one full charge?
  This depends on different vehicle sizes. Large diesels up to 5 times. Petrol vehicles up to 10 times.

• If not being used, how long will the iTECH2000A’s charge last?

• My phone will not charge via Qi?
  Ensure the iTECH2000A is switched on.
  Ensure you have a Qi compatible phone.
  Remove any phone case that may block or lower the charge rate.
  Reposition the phone in the wireless charging area.
  Only one device can be charged at a time via Qi.

• My fridge is not running as long as I expected
  Ensure the fridges low voltage setting is set to “low”.
  Ensure the fridge is already cold.
  Ensure the is no air gaps in the fridge. Fill air gaps with water bottles.
  Ensure your fridge is not set to “freeze”.

• My iTECH2000A will not charge my phone as much as my other iTechworld battery bank.
  When the iTECH2000A is switched on, there is still active circuitry running, even if there is no devices connected to it, this includes the wireless charging pad, backlit screen, and voltage regulation for the USB ports, this consumes power. The iTECH2000A operates differently from other battery banks as the battery pack is at 16 volts, this decreases the usable capacity. Also, the iTECH2000A is designed as a jump starter primarily and functions as battery bank as a secondary feature.

• How can I prolong the life of my iTECH2000A
  Check & charge your iTECH2000A every two months. Always turn the iTECH2000A off after use. Do not leave the iTECH2000A at 0% charge for longer than 7 days. Do not leave the iTECH2000A exposed to direct sunlight. Store the iTECH2000A in a cool & dry environment away from heat and water. Do not attempt to use, charge or discharge the iTECH2000A any other way than what has been stated in this user guide document.

JUMP STARTING CHECK LIST

• Read and understand this user guide in full.
• Prepare the iTECH2000A correctly. (Clamps into the iTECH2000A first then connect to the car battery)  Ensure the iTECH2000A has more than 80% state of charge.
• Ensure the car battery terminals are clean and free from corrosion
• Ensure all 12V accessories (eg radio, fridge.), and headlights are turned off before attempting to jump  start
• Ensure both sides of the alligator clamps are firmly touching the car battery terminals.
• Ensure the small circle button located on the hand piece of the clamps has been pressed before attempting to start the vehicle.
• Note the countdown on the screen of the clamps.
• Start the vehicle before the countdown reaches zero.

TROUBLE SHOOTING

If the iTECH2000A is not functioning correctly, please contact iTechworld on 1300 483 249.

Tine power capacity
i’.s showh1g 100% but
the unit did 1not fully
charge.| The LCD screen shows fully charged, stop charging. This means tine unit is ma semi
state of charge due to, long term storage.| Pull out the charging plug and reconnect.
No, thing happens
when I press tine
round power buttm1| The unit is in low
voltage protection
mode and cannot be
turned on.| Insert the charger
plug into, tine ·9V/2A
input port to activate.

WARNING!

1. After starting your vehicle, REMOVE the ITEC H 2000A as soon as possible.
2. DO NOT connect the 2 alligator dips together.
3. DO INOT disassemble the ITECH 2000A

Do not use the product in bath room or other damp places or IP laces near the water.
Do not remodel or dismantle the device.
Keep the pro duct away from the children .
Do not reverse the connections of output or input.
Do not throw the product into fire.
Only use original charger.
The temperature should be kept between 0°C to 40″C when the device is being charged.
Do not hit or throw the product.
If there is problem with charging, please contact TECHWORLD.
Keep the product away from the flammable objects ( Bed or carpet)
 If  the liquid of the device is splashed into eyes do not wipe the eyes but wash them with clean water immediately.
If the product is heating and discoloring, please stop, using, as it may lead to liquid, smoke and flames.
After long term storage or not in use, please ensure that devices will be charged and discharged every three months.
Do not leave in direct sun light.

QUALITY COMMITMENT
2 MILLION USD SUM
STANDARD: GB/T 18287-2000
Our product’s quality is u1ndeirwritten by Allianz Property and Casualty Company Limited

WARIRANTV

YOUR RECEIPT SIHOULID BE RETAINIED BY YOU AT ALL T’IIM IES. IN ORDER TO CLAIM ANY WARRAINTV, YOU MU,ST RETURIN THE PRODUCT TO YOUR NEAREST ITECHWORLD (SEE WWW.ITECHIWORLD FOR STORE LOCATION) WITH YOUR ITECHWORILD RECIEPT. PRIOR TO RETURNING YOUIR  PRODUCT FOR WARRANTY PLEASE TELEPHONE OUR1CUS,TOMER SERVl1CE HELPLINE.

Australia 1300483249

TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE RIECEIPT NUMIBER AND DATE OF PURCHASE AVAIABLE. A CUSTOMER SERVICE REPRESENTATIVE WILL TAKE YOUR CALL AND ANSWER ANY QUESTIONS YOU MAY HAVE RELATIING TO THIE WARRANTY POLICY OR PROCEDURE.

1 YEAR WARRANTY

Your product is guaranteed for a period of 12 months fro1m original date of purchase. If a product is defective it will be repa11red in accordance with the terms of this warranty.

The, benefits provided under this warranty are· in addition to other rights and remedies which a re a1vailable to you under law .. The warranty covers manufacturer defects in materials, workmanship and finish under normal u.se

Our goods, ,coi1me with guarantees that ,cannot be excluded under Australian Consumer law· a1nd Consu1mer Guarantees Act 1993 (NZ) .
You a re entitled to a 1r,eplai,cement or refund for a major failure. You are, a I.so entitled to have the goods repaired or replaced if the, goods fa ii to be of acceptable, quality and the, failure, does not amount to a ma1jor failure.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>