VOLT VHS-610X-X-BBZ Brass Bunker Thin Integrated Step Light Instruction Manual

: June 13, 2024
: VOLT

Table of Contents

VOLT VHS-610X-X-BBZ Brass Bunker Thin Integrated Step Light
Product Information
Package Contents
Product Dimensions
Product Usage Instructions
INSTALLATION INSTRUCTIONS
Important Safety Instructions
Install Luminaire
Wire Connection
MODELS
CONTACT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

VOLT VHS-610X-X-BBZ Brass Bunker Thin Integrated Step Light

Product Information

The Light VHS-610X-X-BBZ is a luminaire designed for installation in accordance with local codes and the National Electric Code (NEC). It is intended to be used with a power supply (transformer) rated maximum of 300 watts (25 AMPS) at 15 volts. The luminaire is suitable for outdoor use and comes with a main low-voltage cable for shallow burial. It is important to follow the installation instructions and adhere to the safety guidelines to prevent any injuries or property damage.

Package Contents

(1) Luminaire
(2) Anchors
(2) Screws

Product Dimensions

VHS-6100-X-BBZ: 8.25″ x 3.25″ x 0.75″
VHS-6101-X-BBZ: 8.25″ x 1.5″ x 3.25″
VHS-6102-X-BBZ: 8.25″ x 0.5″

Product Usage Instructions

Install Luminaire
If installing on concrete or brick walls, use anchors. Hold the luminaire on the wall and mark two points for the anchors using the mounting holes as guides.
Drill the proper holes using the marked points.
Insert the anchors into the drilled holes.
Attach the luminaire onto the desired mounting surface and secure it with screws.
Tighten the screws with a screwdriver until snug.
Wire Connection
- Strip both leads from the luminaire pigtail. Using two wire connectors (sold separately), connect the leads from the luminaire to the main supply cable leads.
- For additional lengths of low-voltage cable, please contact www.voltlighitng.com or call 1-813-978-3700.
- For detailed safety instructions and other installation variations, please refer to the complete user manual available at www.voltlighting.com.

INSTALLATION INSTRUCTIONS

Important: Please Read Before Installation
This luminaire is intended for installation in accordance with local codes and the National Electric Code (NEC). Failure to adhere to these codes and instructions may result in serious injury, and property damage and void the warranty.

These instructions do not intend to cover all variations in installation, operation maintenance, or mounting situations.

Make sure that the power is turned OFF before installing or servicing this luminaire.
Warning: risk of electrical shock. Install all luminaires 10 feet (3.05M)or more from the pool, spa, or fountain.
This luminaire is intended to be used only with a power supply(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
Wiring connections must be made with UL-listed wire connectors that are suitable for outdoor use.
Position the low voltage wire and wire connector so that it is located within 6 inches (15.2 cm) from a building structure, a luminaire orfitting.
The main low-voltage cable is intended for shallow burial – less than 6 inches (152mm).
If additional lengths of low-voltage cable is required, please contact www.voltlighitng.com. or call 1-813-978-3700.

Important Safety Instructions

INSTRUCTIONS PERTAINING A RISK OF FIRE, OR INJURY TO PERSONS Lighted Lamp is HOT!

WARNING – TO REDUCE THE RISK OF FIRE OR INJURY TO PERSONS.

Turn off/unplug and allow to cool before replacing the lamp.
The lamp gets HOT quickly! Contact only switch/plug when turning on.
Do not touch the hot lens, guard or enclosure.
Keep lamps away from materials that may burn.
Do not touch the lamp at any time. Use a soft cloth. Oil from the skin may damage the lamp.
Do not operate the luminaire fitting with a missing or damaged shield.

Package Contents

A. (1) Luminaire
B. (2) Anchors
C. (2) Screws

Product Dimensions

$VOLT-VHS-610X-X-BBZ-Brass-Bunker-Thin-Integrated-Step-Light-FIG-1 $1$$

Install Luminaire

Note: Anchors are required for concrete or brick walls. Hold the luminaire on the wall and mark two points for the anchors using the mounting holes as guides. Then drill the proper holes using the marks. Insert the anchors into the drilled holes.Attach the luminaire onto the desired mounting surface and secure with the screws. Hand tighten until snug with a screwdriver.

Wire Connection

$VOLT-VHS-610X-X-BBZ-Brass-Bunker-Thin-Integrated-Step- Light-FIG-1 $3$$

Strip both leads from the luminaire pigtail. Using two wire connectors (sold separately), connect the leads from the luminaire to the main supply cable leads.