KLEIN TOOLS 5144LG2 2 Inch Gated Bucket Hook Instructions
- June 13, 2024
- KLEIN TOOLS
Table of Contents
5144LG2 2 Inch Gated Bucket Hook
ANSI/ISEA 121-2018 Dropped Object Prevention Tether Point is a
product designed to prevent objects from falling and causing
potential hazards. It has a maximum load capacity of 7lbs (3kg) and
a maximum tether length of 4′ (1.2m). Please note that it is
important to inspect the product before each use to ensure its
integrity and functionality. To use the ANSI/ISEA 121-2018 Dropped
Object Prevention Tether Point, follow the instructions below: 1.
Inspect the tether point: Before each use, carefully examine the
tether point for any signs of damage or wear. Check for any frayed
or cut parts, loose stitching, or weakened areas. If you notice any
defects, do not use the product and contact customer support for
further assistance. 2. Attach the tether: Identify a suitable
anchor point on your equipment or tool that can securely hold the
tether. Ensure that the anchor point is capable of supporting the
maximum load of 7lbs (3kg). Connect one end of the tether to the
anchor point using the provided attachment mechanism, such as a
carabiner or loop. 3. Attach the other end: Connect the opposite
end of the tether to your equipment or tool. Make sure to secure it
properly, ensuring that it cannot detach during use. Double-check
the attachment to ensure it is secure and reliable. 4. Adjust the
tether length: If necessary, adjust the length of the tether to
your desired working distance. Ensure that the tether is neither
too loose nor too tight, maintaining a safe working environment. 5.
Inspect before each use: Always inspect the tether point before
each use to verify its condition. Look for any signs of wear,
damage, or deterioration. If any issues are detected, discontinue
using the product and replace it with a new one. By following these
instructions and regularly inspecting the ANSI/ISEA 121-2018
Dropped Object Prevention Tether Point, you can enhance safety and
prevent potential accidents caused by dropped objects.
GATED BUCKET HOOK INSTRUCTIONS
GANCHO CON CIERRE PARA CANASTILLA INSTRUCCIONES
CROCHET FERMÉ POUR NACELLE INSTRUCTIONS
ANSI/ISEA 121-2018 Dropped Object Prevention Tether Point Max Load: 7lbs (3kg)
Max Tether Length: 4′ (1.2m) NOTE: Inspect before each use
Prevención de caída de objetos según la norma ANSI/ISEA 121-2018 Carga máxima
del punto para atar cuerdas: 7 lb (3 kg) Longitud máxima de sujeción: 4′ (1,2
m) NOTA: Examine antes de cada uso
ANSI/ISEA 121-2018 (prévention des chutes d’objets) Poids maximal au point
d’attache : 3 kg (7 lb) Longueur maximale de l’attache : 1,2 m (4 pi) REMARQUE
: Inspectez le produit avant chaque utilisation.
5144LG2 & 5144LG3
1331082 Rev 06/23 A
Interior hook for buckets, tools and gear Gancho interior para cubetas,
herramientas y accesorios Crochet intérieur pour les seaux, les outils et le
matériel
Tether point here Punto de sujeción para atar cuerdas aquí Point d’attache ici
Lockable gate helps reduce the risk of tools falling Cierre que se bloquea
para ayudar a reducir el riesgo de caída de las herramientas Dispositif
verrouillable pour réduire le risque de chute des outils
Exterior locking hook for static loads up to 40 lbs Gancho de bloqueo exterior
para cargas estáticas de hasta 40 lb Crochet extérieur verrouillable pour des
charges statiques jusqu’à 40 lb
Not a Tether Point even when gate is opened or closed No es un punto para atar
cuerdas, incluso cuando el cierre está abierto o cerrado Pas de point
d’attache, que le dispositif soit verrouillé ou déverrouillé
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>