BRAUN 5197cc Clean and Charge Station Instruction Manual
- June 13, 2024
- Braun
Table of Contents
BRAUN 5197cc Clean and Charge Station
Our products are designed to meet the highest standards of quality, functionality and design. Thank you for your trust in Braun’s quality and we hope you enjoy your new Braun product. Read these instructions completely, they contain safety information. Keep them for future reference.
Warning
Your appliance is provided with a special cord set, which has an integrated
Safety Extra Low Voltage power supply. Do not exchange or tamper with any part
of it, otherwise there is risk of an electric shock. Only use the special cord
set provided with your appliance.
If the appliance is marked 492, you can use it with any Braun power supply
coded 492-XXXX.
This appliance is suitable for cleaning under running water and use in a bathtub or shower. For safety reasons it can only be operated cordless.
Detach the shaver from the power supply before using it with water. Do not shave with a damaged foil or cord. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capa-bilities or lack of experience and knowledge if they have been given supervision or instruction concerning the safe use of the appliance and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children unless they are older than 8 years and supervised.
Clean & Charge Station
To prevent the cleaning fluid from leaking, ensure that the Clean&Charge
Station is placed on a flat surface. When a cleaning cartridge is installed,
do not tip, move suddenly or transport the station in any way as cleaning
fluid might spill out of the cartridge. Do not place the station inside a
mirror cabinet, nor place it on a polished or lacquered surface. The cleaning
cartridge contains a highly flammable liquid so keep it away from sources of
ignition. Do not expose to direct sunlight and cigarette smoking nor store it
over a radiator. Do not refill the cartridge and use only original Braun
refill cartridges.
Shaver
- Foil & Cutter cassette
- Cassette release button
- MultiHeadLock switch
- On/off switch
- Shaver display
- a Lock symbol (travel lock)
- b Charging segments
- c Cleaning indicator
- d Battery symbol
- Long hair trimmer
- Shaver-to-station contacts
- Release button for long hair trimmer
- Shaver power socket
- a Special cord set (design can differ)
- b Charging stand*
- Protection cap*
- Travel case*
- not with all models
First use and charging
Connect the shaver to an electrical outlet by snapping the special cord set (10a) into the shaver power socket (9) / the charging stand (10b) or for cc models via the Clean&Charge Station (see Chapter «Clean&Charge Station»).
Basic operating information
- A full charge provides up to 50 minutes of cordless shaving time. This may vary according to your beard growth and environmental temperature.
- The recommended ambient temperature for charging is 5 °C to 35 °C. The battery may not charge properly or at all under extreme low or high temperatures.
- The recommended ambient temperature for storage and shaving is 15 °C to 35 °C.
- Do not expose the appliance to temperatures higher than 50 °C for extended periods of time.
- When the shaver is connected to an electrical outlet, it may take some minutes until the display illuminates.
Charging / low charge
The charge status is shown in the shaver display (5).
- During charging the respective charging segment (5b) will blink.
- When the shaver is fully charged and connected to an electrical outlet, all 3 charging segments will light up for a few seconds. Then the display turns off.
- The battery symbol (5d) will flash red, when the battery is running low. You should be able to finish your shave. With switching off the shaver a beep sound reminds of the low charge status.
Using the shaver
Press the on/off switch (4) to operate the shaver.
Tips for a perfect dry shave
For best results, Braun recommends you to follow 3 simple steps:
- Always shave before washing your face.
- At all times, hold the shaver at the right angle (90°) to your skin.
- Stretch your skin and shave against the direction of your beard growth.
MultiHeadLock switch (headlock)
- To shave hard-to-reach areas (e.g. under the nose) slide the MultiHeadLock switch (3) down to lock the shaver head.
- The shaver head can be locked in five positions. To change position, move the shaver head with your thumb and forefinger back or forth. It will automatically click into the next position.
- For automatic cleaning in the Clean&Charge Station the head lock should be released.
Long hair trimmer
To trim sideburns, moustache or beard press the release button (8) and slide
the long hair trimmer (6) upwards.
Travel lock
- The lock symbol (5a) lights up in the display when the shaver has been locked to avoid the unintended starting of the motor (e.g. for storing it in a suitcase).
- Activation: By pressing the on/off switch (4) for 3 seconds the shaver is locked. This is confirmed by a beep sound and the lock symbol in the display. Afterwards, the display turns off.
- Deactivation: By pressing the on/off switch for 3 seconds again the shaver is unlocked.
Manual cleaning of the shaver
Cleaning under running water
- Switch on the shaver (cordless) and rinse the shaver head under hot running water until all residues have been removed. You may use liquid soap without abrasive substances. Rinse off all foam and let the shaver run for a few more seconds.
- Next, switch off the shaver, press the release button (2) to remove the Foil & Cutter cassette (1) and let it dry.
- If you regularly clean the shaver under water, then once a week apply a drop of light machine oil on top of the Foil & Cutter cassette.
The shaver should be cleaned after each foam usage.
Cleaning with a brush
- Switch off the shaver. Remove the Foil and cutter cassette (1) and tap it out on a flat surface. Using the brush, clean the inner area of the pivoting head. Do not clean the cassette with the brush as this may damage it!
Clean&Charge Station (C&C) (not with all models)
The Clean&Charge Station has been developed for cleaning, charging,
lubricating, disinfecting, drying and storing your Braun shaver.
-
13 Station power socket
-
14 Lift button for cartridge exchange
-
15 Station-to-shaver contacts
-
16 Clean&Charge Station display
-
16 a Level indicator
b Status light
c Cleaning program indicators -
17 Start button
-
18 Cleaning cartridge
Installing the C &C
- Remove the protection foil from the C&C display.
- Press the lift button (14) at the rear side of the C&C to lift up the housing.
- Hold the cleaning cartridge (18) down on a flat, stable surface (e.g. table).
- Carefully remove the lid from the cartridge.
- Slide the cartridge from the rear side into the base of the station until it snaps into place.
- Slowly close the housing by pushing it down until it locks.
- Using the special cord set (10a), connect the station power socket (13) to an electrical outlet.
Using the C &C
Important: The shaver needs to be dry and free from any foam or soap
residue! Insert the shaver in the C&C upside down, with the front showing and
released head lock (3). The contacts (7) on the back of the shaver need to
align with the contacts (15) in the C&C. Push the shaver in the correct
position. A beep sound confirms that the shaver sits properly in the C&C. The
C&C analyzes the hygiene status. The status is shown by the cleaning program
indicators (16c) in the C&C display (16).
Charging the shaver in the C &C
Charging will start automatically when the shaver has been placed in properly.
Cleaning the shaver in the C &C
When the cleaning indicator (5c) lights up in the shaver display, insert the
shaver into the C&C, as described above.
- Cleaning programs
- Start automatic cleaning
Start the cleaning process by pressing the start button (17). If status light (16b) does not shine (C&C switches to stand-by after ca. 10 minutes), press start button twice. Otherwise cleaning will not start. For best shaving results, we recommend cleaning after each shave. Each cleaning program consists of several cycles, where cleaning fluid is flushed through the shaver head. Depending on your Clean&Charge Station model and/or program selected, the cleaning time takes up to 3 minutes. During this time the status light blinks. Leave the shaver in the station for drying. It takes several hours until the remaining moisture evaporates depending on the climatic conditions. After completing the cleaning and charging procedure, all indicators turn off.
Removing the shaver from the C &C
Hold the C&C with one hand and tilt the shaver slightly to the front to
release it.
Cleaning cartridge / Replacement
When the level indicator (16a) lights up permanently red, the remaining fluid
in the cartridge is sufficient for about 3 more cycles. When the level
indicator blinks red, the cartridge needs to be replaced – about every 4 weeks
when used daily. After having pressed the lift button (14) to open the
housing, wait for a few seconds before removing the used cartridge to avoid
any dripping. Before discarding the used cartridge, make sure to close the
openings using the lid of the new cartridge, since the used cartridge will
contain a contaminated cleaning solution. The hygienic cleaning cartridge
contains ethanol or isopropanol (specification see cartridge), which once
opened will naturally evaporate slowly. Each cartridge, if not used daily,
should be replaced after approximately 8 weeks to ensure optimal disinfection.
The cleaning cartridge also contains lubricants for the shaving system, which
may leave residual marks on the outer foil frame and the cleaning chamber of
the C&C. These marks can be removed easily by wiping gently with a damp cloth.
Accessories
Braun recommends changing your shaver’s Foil and cutter cassette every 18 months to maintain your shaver’s maximum performance. Available at your dealer or Braun Service Centres:
- Foil & Cutter cassette: 52S/52B
- Cleaning Cartridge: CCR
- Braun Shaver cleaner spray
Environmental notice
Product contains batteries and/or recyclable electric waste. For
environment protection do not dispose of in household waste, but for recycling
take to electric waste collection points provided in your country. The
cleaning cartridge can be disposed of with regular household waste. Subject to
change without notice. For electric specifications, see printing on the
special cord set.
Trouble-Shooting
| Problem | Possible reason | Remedy |
|---|
SHAVER
Shaver does not charge completely and keeps blinking.| Ambient temperature is
out of valid range.| Recommended ambient temperature for charging is 5 °C to
35 °C.
Charging does not start when connected to power socket.| 1. Sometimes
charging could start delayed (e.g. after long storage).
2. Ambient temperature is out of valid range.
3. Special cord set is not plugged in properly.
| 1. Wait a few minutes, if charging will start automatically.
2. Recommended ambient temperature for charging is 5 °C to 35 °C.
3. Special cord set needs to snap into place.
Unpleasant smell from the shaver head.| 1. Shaver head is cleaned with water.
2. Cleaning cartridge is in use for more than 8 weeks.
| 1. When cleaning the shaver head with water only use hot water and from time to time some liquid soap (without abrasive substances). Remove Foil & Cutter cassette to let it dry.
2. Change cleaning cartridge at least every 8 weeks.
---|---|---
Battery performance dropped significantly.| 1. Foil and cutter are worn which
requires more power for each shave.
2. Shaver head is regularly cleaned with water but not lubricated.
| 1. Renew Foil & Cutter cassette.
2. If the shaver is regularly cleaned with water, apply a drop of light machine oil on top of the foil once a week for lubrication.
Shaving performance dropped significantly.| 1. Foil and cutter are worn.
2. Shaving system is clogged.
| 1. Renew Foil & Cutter cassette.
2. Soak the Foil & Cutter cassette into hot water with a drop of dish liquid. Afterwards rinse it properly and tap it out. Once dry apply a drop of light machine oil on the foil.
Shaver head is damp.| 1. Drying time after automatic cleaning was too short.
2. Drain of the Clean&Charge Station is clogged.
| 1. Clean directly after shaving to allow enough time for drying.
2. Clean the drain with a wooden toothpick.
CLEAN&CHARGE STATION
Cleaning does not start when pressing the start button.| 1. Shaver is not
placed properly in the Clean&Charge Station.
2. Cleaning cartridge contains not enough cleaning fluid (display blinks red).
| 1. Insert shaver into the Clean&Charge Station and push it to the rear side of the station (contacts of the shaver need to align with contacts in the station).
2. Insert new cleaning cartridge. Press start button again.
Increased consumption of cleaning fluid.| Drain of the Clean& Charge station is clogged.| – Clean the drain with a wooden toothpick.
– Regularly wipe the tub clean.
Guarantee
We grant a 2-year guarantee on the product commencing on the date of purchase.
Within the guarantee period we will eliminate any defects in the appliance
resulting from faults in materials or workmanship, free of charge either by
repairing or replacing the complete appliance at our discretion. This
guarantee extends to every country where this appliance is supplied by Braun
or its appointed distributor.
This guarantee does not cover: damage due to improper use, normal wear or
use as well as defects that have a negligible effect on the value or operation
of the appliance. The guarantee becomes void if repairs are undertaken by
unauthorized persons and if original Braun parts are not used. To obtain
service within the guarantee period, hand in or send the complete appliance
with your sales receipt to an authorized Braun Customer Service Centre
(address information available online at www.service.braun.com).
For UK only:
This guarantee in no way affects your rights under statutory law.
For Australia & New Zealand only:
Warranty
In Australia, our goods come with guarantees that cannot be excluded under the
Australian Consumer Law. You are entitled to a replacement or refund for a
major failure and for compensation for any other reasonably foreseeable loss
or damage. You are also entitled to have the goods repaired or replaced if the
goods fail to be of acceptable quality and the failure does not amount to a
major failure.
The benefits given by this warranty are in addition to other rights and
remedies of the consumer law.
For Claims in Australia please contact:
Procter & Gamble Australia Pty Ltd 1 Innovation Road, Macquarie Park
NSW 2113
Telephone: +612 8864 5000
Facsimile: +612 8864 5574
Email: gillette@au.pgconsumers.com
For claims in New Zealand please contact:
Procter & Gamble Distributing New Zealand Limited
c/o Simpson Grierson
88 Shortland Street, Auckland 1010
New Zealand
Telephone: +649 477 6400
Facsimile: +649 477 6399
Email: gillette@nz.pgconsumers.com
Our Warranty
This appliance is also covered by a 24 Month Replacement Warranty commencing
on the date of purchase (Our Warranty).
Our Warranty applies in all States and Territories of Australia and in New
Zealand and is in addition to any mandatory statutory obligations imposed on
Procter & Gamble Australia Pty. Ltd., its distributors and its manufacturer.
Our Warranty does not purport to exclude, restrict or modify any such
mandatory statutory obligations. Our Warranty only covers defects in the
appliance resulting from faults in workmanship or materials. Therefore, if
your appliance becomes faulty as a result of faults in workmanship or
materials, it will be exchanged by your retailer, on presentation of proof of
purchase. Our Warranty only applies to domestic or household use of this
appliance and the warranty will only apply if the correct operating
instructions included with this product have been followed. For any appliance
replaced under this warranty, Our Warranty ends on the expiry of the warranty
period that applied to the original appliance.
Our Warranty does not cover:
- A. Damage arising from improper use or operation on incorrect voltages.
- B. Breakages to shaver foils, glass jars, etc.
- C. Normal wear due to moving parts.
- D. Repairs are undertaken by unauthorized service personnel or use of nongenuine parts.
- E. Appliances that are outside the warranty period or are not faulty.
This appliance is not intended for use by young children or infirm persons without supervision. Young children should be supervised to ensure that they do not play with the appliance. If the appliance is powered by a cord extension set or electrical portable outlet device these should be positioned so they are not subject to splashing or ingress of moisture. To the extent permitted by the laws of the Commonwealth of Australia and New Zealand and applicable laws of a State or Territory of Australia, and without affecting any mandatory statutory obligations imposed by law, Our Warranty is given in exchange for any other rights you may have against Procter & Gamble Australia Pty. Ltd. or its distributors or manufacturer, whether at law, in tort (including negligence), in equity or under the statute. Please retain proof of purchase of this appliance. If you have any questions in relation to Our Warranty, please call our Consumer Service line (see below for numbers). If you intend to make a claim please telephone our Customer Service line on the numbers set out below to obtain information about your claim and any costs associated with claiming under Our Warranty. You will bear the cost of returning your product to us.
Repairs and service
If you are sending your appliance for repair under Our Warranty, please pack
the appliance adequately and send it to your nearest Service Agent, at your
expense.
For service or replacement parts refer to the authorised Service Agents listed
below. Local Service Agents may change from time to time – in that event
please contact the Consumer Service free call number below for updated local
service agent details.
Australian Consumer Service (free call): 1 800 641 820
New Zealand Consumer Service (free call): 0 800 108 909
Australian & New Zealand Service Agents
VICTORIA & TASMANIA
Statewide Services Pty Ltd trading as J A Appliances
17-19 Hossack Avenue
Coburg North, VIC 3058
Tel. (03) 8371 9100
Fax. (03) 9355 8644
Email:
jaappliances@statewideservices.com.au
NEW SOUTH WALES & ACT
Faulder Appliance Services Pty Ltd Shop 4,
9 Evans Road,
Rooty Hill, NSW 2766
Tel. (02) 9625 3064
Fax. (02) 9625 3037
Email: fas16@bigpond.com
QUEENSLAND
Walters Import trading as Brisbane Appliance Service Centre 449 Beaudesert
Road Moorooka QLD 4105
Tel. (07) 3277 0360
Fax. (07) 3274 2909
Email: basc@waltersimport.com.au
SOUTH AUSTRALIA & NT
Adelaide Service Centre Shop B2, Parkholme Shopping Centre 319 Oaklands Road,
Parkholme Adelaide, SA 5043
Tel. (08) 8357 5800
Fax. (08) 8357 5833
Email: ascpkh@adam.com.au
WESTERN AUSTRALIA
Mark 1 Appliances Unit 1, 46 Abernethy Road Belmont, WA 6104
Tel. (08) 9475 0911
Fax. (08) 9475 0922
Email: mark1app@iinet.net.au
NEW ZEALAND
Key Service Ltd 7D Echelon Place East Tamaki Manukau City Auckland New Zealand
(PO Box 38569, Howick, Auckland, New Zealand)
Tel. (09) 916 0960
Fax. (09) 916 0970
Email: key-service-ltd@xtra.co.nz
Braun GmbH
Frankfurter Straße 145
61476 Kronberg/Germany
www.braun.com
www.service.braun.com
References
- Manual-Hub.com - Free PDF manuals!
- Braun Electric Shavers and Razors | Braun
- Braun Service
- Manual-Hub.com – Free PDF manuals!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>