VOLT VAL-1052-BBZ Modernelle Flat Top Brass Path Light Bronze Instruction Manual
- June 13, 2024
- VOLT
Table of Contents
INSTALLATION INSTRUCTIONS
VOLT® LOW VOLTAGE LANDSCAPE LIGHTING
VAL-1052-BBZ Modernelle Flat Top Brass Path Light Bronze
VOLT ® Modernelle Flat Top
Brass Path Light (Bronze)
ITEM: VAL-1052-BBZ
1-813-978-3700
Mon-Fri 8am-8pm
Sat-Sun 10am – 6pm (EST)
IMPORTANT: PLEASE READ BEFORE INSTALLATION
This luminaire is intended for installation in accordance with local codes and
the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
- Make sure that the power is turned OFF before installing or servicing this luminaire.
- WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M) or more from pool, spa or fountain.
- This luminaire is intended to be used only with a power supply (transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
- Wiring connections must be made with UL listed wire connectors that are suitable for outdoor use.
- Position the low voltage wire and wire connector so that it is located within 6 inches (15.2 cm) from a building structure, a luminaire or fitting.
- The main low voltage cable is intended for shallow burial – less than 6 inches (152 mm).
**** IMPORTANT SAFETY INSTRUCTIONS
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – TO REDUCE THE RISK OF FIRE OR INJURY TO PERSONS.
- Turn off/unplug and allow to cool before replacing lamp.
- Lamp gets HOT quickly! Contact only switch/plug when turning on.
- Do not touch the hot lens, guard or enclosure.
- Keep lamp away from materials that may burn.
- Do not touch lamp at any time. Use a soft cloth. Oil from skin may damage lamp.
- Do not operate the luminaire fitting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS
PACKAGE CONTENTS
A. (1) Fixture Body
Parts Required (Sold Separately)
A. (1) G4 Bulb
B. Mounting Accessory
PRODUCT DIMENSIONS
INSTALLATION INSTRUCTIONS
-
REMOVE LENS
Remove the lens from the fixture. -
Install G4 Bulb
Insert G4 bulb with correct wattage and type marked on fixture label.
CAUTION: Do not exceed maximum wattage marked on luminaire label. -
Install Lens
Place the lens back onto the fixture and secure with previously removed screws. -
Install Lamp Body to Stake
Pass the fixture wire through the stake and thread the stake onto the fixture. Thread the lock ring against the stake and hand tighten until snug. -
INSTALL STAKE
Determine the desired location for mounting the fixture. Insert the stake into the ground until flange of stake is flush to grade.
NOTE: If the ground is hard and the stake is difficult to install, make a crosscut in the ground using a flat shovel.
-
WIRE CONNECTION
Strip both the leads from the luminaire pigtail. Using two UL listed wire connectors (sold separately), connect the leads from the luminaire to the main supply cable leads.
INSTALL REPLACE BULB
Please reverse Step 2 – Step 3 to expose the G4 bulb and replace it with the
correct wattage and type marked on the fixture label.
Then, reinstall the shade.
IMPORTANT: The G4 bulb must be protected from moisture and dust at all
times. Always reinstall the shade when moved.
1-813-978-3700 • Mon-Fri 8am-8pm •
Sat-Sun 10am – 6pm (EST)
Specifications and product details subject to change without notice.
© Copyright 2023, VOLT® Lighting, Lutz FL USA 33549
All rights reserved.
customersupport@voltlighting.com
www.voltlighting.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>