Hertz K 170 Uno Series 6-3/4 Component Speaker System Owner’s Manual
- June 13, 2024
- HERTZ
Table of Contents
Hertz K 170 Uno Series 6-34 Component Speaker System
Congratulations on purchasing our product. Your satisfaction is the first requirement that our products must meet: the same satisfaction as the one gained by those who long for experiencing the car audio emotion. This manual has been drawn to provide the main instructions required to install and use the system properly. However, the range of possible applications is wide; for further information, please feel free to contact your trusted dealer or our technical support at the email support@elettromedia.it Before installing the components, please carefully read all of the instructions contained in this manual. Failure to respect these instructions may cause unintentional harm or damage to the product.
- All components must be firmly secured to the vehicle structure. Do the same when installing any custom structures you may have built. Confirm your installation is solid and safe. A component coming loose while driving may cause serious damage to the passengers, as well as to other vehicles.
- Always wear protective eyewear when using tools, as splints or product residue may become airborne.
- In order to avoid incidental damage, keep the product in the original packaging until you are ready for the final installation.
- Do not carry out any installation inside the engine compartment.
- Before starting with the installation turn the head unit and all other audio system devices off, avoiding any possible damage.
- Make sure that the location you choose to install the components does not interfere with the normal operation of any mechanical or electrical devices of the vehicle.
- Do not install loudspeakers where they may be exposed to water, excessive humidity, dust or dirt.
- Do not install the tweeter without the protective grille.
- Do not install the components or make cable run close to electronic or mechanical devices of the vehicle.
- Be very cautious when drilling or cutting into the vehicle chassis, making sure there are no cables or structural elements essential to the vehicle underneath or in the selected area.
- When routing cables, make sure that the cable does not come in contact with sharp edges or near moving mechanical devices. Make sure that it is firmly attached and protected along its entire length and its insulation is self-extinguishing.
- Only use cables with the proper section (AWG) indicated herein.
- When running the cable through a hole in the vehicles chassis, protect the cable with a rubber ring (grommet). Be sure to provide proper protection for cables running close to heat-generating devices.
- Do not run the wires outside of the vehicle.
- Use top quality cables, connectors and accessories such as found in the Connection catalogue.
- Warranty certificate: For more information visit the Hertz website.
Packaging contents
Connections
Technical specifications
All Specifications Subject to Change Without Notice
Component| Size| Power handling| Impedance| Frequency response| Sensitivity|
Weight of one component
---|---|---|---|---|---|---
Peak| Continuous
mm (in.)| W| W| Ω| Hz| dB/SPL| Kg (lb.)
X 130| Two way coaxial| Woofer 130 (5)| 160| 40| 4| 60 ÷ 21k| 93| 0,56 (1.23)
Tweeter diaphragm 24 (0.9)
X 165| Two way coaxial| Woofer 165 (6.5)| 220| 55| 4| 60 ÷ 21k| 93,5| 0,73
(1.61)
Tweeter diaphragm 24 (0.9)
X 170| Two way coaxial| Woofer 170 (6.7)| 200| 50| 4| 60 ÷ 21k| 93,5| 0,56
(1.23)
Tweeter diaphragm 24 (0.9)
X 690| Four way coaxial| Woofer (6×9)| 340| 85| 4| 45 ÷ 22k| 94| 0,93 (2.05)
Tweeter diaphragm 40 (1.6)
Super tweeter diaphragm 2 x 15 (0.6)
K 130| Two way System| Woofer 130 (5)| 220| 55| 4| 55 ÷ 23k| 93| 0,53 (1.17)
Tweeter diaphragm 24 (0.9)| 0,03 (0.07)
K 165| Two way System| Woofer 165 (6.5)| 300| 75| 4| 55 ÷ 23k| 93,5| 0,7
(1.54)
Tweeter diaphragm 24 (0.9)| 0,03 (0.07)
K 170| Two way System| Woofer 170 (6.7)| 280| 70| 4| 55 ÷ 23k| 93,5| 0,53
(1.17)
Tweeter diaphragm 24 (0.9)| 0,03 (0.07)
Specification
T 24 – Tweeter:
- 24mm diaphragm Neodymium tweeter with PEI dome, for a brilliant reproduction of high frequencies in a compact size.
- Annular acoustic lens optimized for exceptional off-axis performance.
- 6dB/Oct crossover integrated on tweeter wiring.
- Mounting accessories for external or embedded mounting included.
V 170 – Woofer:
- V-cone® design for best off-axis response, clear mid-high frequency detail and powerful bass.
- Foam surround combining high sensitivity and deep bass response.
- Pure copper 25mm (1 in.) voice coil woofer for high dynamic power handling.
- High flux density 80mm (3.15 in.) ferrite magnet for a powerful undistorted sound.
- Easy-to-install DIN size basket protected by abrasion-resistant dust paint.
TECHNICAL SPECIFICATIONS
| Component | 2-way system |
|---|
Size
Woofer| mm (in.)| 170 (6.7)
Tweeter diaphragm| mm (in.)| 24 (0.9)
Voice Co i l Ø
Woofer| mm (in.)| 25 (1)
Tweeter| mm (in.)| 14 (0.55)
Power Handling|
- W peak
- W continuous
|
- 280
- 70
Sensitivity| dB SPL| 93,5
Impedance| 0| 4
Frequency Response| Hz| 55 + 23k
Crossover| 6 dB/Oct tweeter integrated
We i ghtof one component
Woofer| kg(lb)| 0,53 (1.17)
Tweeter| kg (lb)| 0,03 (0.07)
Woofer Magnet| High density flux ferrite
Tweeter Magnet| Neodymium
Cone| Water- repellent pressed paper
Dome| PEI
Xmech| mm (in.)| ±3 (0.12)
A| 165 mm| 6.5 in.
---|---|---
B| 140 mm| 5.51 in.
C| 51 mm| 2.01 in.
D| 45 mm| 1.77 in.
| A | 34 mm | 1.3 in. |
|---|---|---|
| C | 20 mm | 0.8 in. |
| D | 13 mm | 0.5 in. |
Customer Support
PART OF ELETTROMEDIA
Strada Regina Km 3,500 – Marignano
62018 Potenza Picena (MC) Italy
T +39 0733 870 870 – F +39 0733 870 880
www.elettromedia.it
Elettromedia – 62018 Potenza Picena (MC) Italy – T +39 0733 870 870 – F +39 0733 870 880 – www.elettromedia.it
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>