HERTZ 301MP283 Mille Pro Car Audio Systems Owner’s Manual

June 4, 2024
HERTZ

HERTZ logo Mille
PRO
OWNER’S MANUAL
Comp – System – Coax
HERTZ 301MP283 Mille Pro Car Audio Systems -
.

301MP283 Mille Pro Car Audio Systems

Congratulations on purchasing our product. Your satisfaction is the first requirement that our products must meet: the same satisfaction as the one gained by those who long for experiencing the car audio emotion. This manual has been drawn to provide the main instructions required to install and use the system properly. However, the range of possible applications is wide; for further information, please feel free to contact your trusted dealer or our technical support at email support@elettromedia.it Before installing the components, please carefully read all of the instructions contained in this manual. Failure to respect these instructions may cause unintentional harm or damage to the product.

  1. All components must be firmly secured to the vehicle structure. Do the same when installing any custom structures you may have built. Confirm your installation is solid and safe. A component coming loose while driving may cause serious damage to the passengers, as well as to other vehicles.
  2. Always wear protective eyewear when using tools, as splints or product residue may become airborne.
  3. In order to avoid incidental damage, keep the product in the original packaging until you are ready for the final installation.
  4. Do not carry out any installation inside the engine compartment.
  5. Before starting with the installation turn the head unit and all other audio system devices off, avoiding any possible damage.
  6. Make sure that the location you choose to install the components does not interfere with the normal operation of any mechanical or electrical devices of the vehicle.
  7. Do not install loudspeakers where they may be exposed to water, excessive humidity, dust, or dirt.
  8. Do not install the tweeter without the protective grille.
  9. Do not install the components or make cable run close to the electronic or mechanical devices of the vehicle.
  10. Be very cautious when drilling or cutting into the vehicle chassis, making sure there are no cables or structural elements essential to the vehicle underneath or in the selected area.
  11. When routing cables, make sure that the cable does not come in contact with sharp edges or near-moving mechanical devices. Make sure that it is firmly attached and protected along its entire length and that its insulation is self-extinguishing.
  12. Only use cables with the proper section (AWG) indicated herein.
  13. When running the cable through a hole in the chassis of the vehicle, protect the cable with a rubber ring (grommet). Be sure to provide proper protection for cables running close to heat-generating devices.
  14. Do not run the wires outside of the vehicle.
  15. Use top-quality cables, connectors, and accessories such as those found in the Connection catalog.
  16. Warranty certificate: For more information visit the Hertz website.

SAFE SOUND
USE COMMON SENSE AND PRACTICE SAFE SOUND. PLEASE REMEMBER THAT LONG EXPOSURE TO EXCESSIVELY HIGH SOUND PRESSURE LEVELS MAY DAMAGE YOUR HEARING. SAFETY MUST BE AT THE FOREFRONT WHILE DRIVING.
Information on electrical and electronic equipment waste (for those European countries which organize the separate collection of waste)
Products that are marked with a wheeled bin with an X through it can not be disposed of together with ordinary domestic waste. These electrical and electronic products must be recycled in proper facilities, capable of managing the disposal of these products and components. In order to know where and how to deliver these products to the nearest recycling/disposal site please contact your local municipal office. Recycling and disposing of waste in a proper way contributes to the protection of the environment and prevents harmful effects on health.

Packaging contents

HERTZ 301MP283 Mille Pro Car Audio Systems -

Size

MP 25.3 – MP 28.3

HERTZ 301MP283 Mille Pro Car Audio Systems - fig 1

A| B| C| D|
---|---|---|---|---
MP 25. 3| 44| 41| 27| 17| mm
1.73| 1.61| 1.06| 0.67| in.
MP 28. 3| 53,4| 48| 28| 13,5| mm
2.1| 1.89| 1.1| 0.53| in.

Flush mounting

MP 25.3 – MP 28.3

HERTZ 301MP283 Mille Pro Car Audio Systems - fig 2

X 1| X 2| X 3|
---|---|---|---
MP 25 .3

MP 28 .3

| 66| 91| 116| mm
2.6| 3.58| 4.57| in.

Asennus pinnan tasoon

MP 25.3

HERTZ 301MP283 Mille Pro Car Audio Systems - fig 3

MP 28.3

HERTZ 301MP283 Mille Pro Car Audio Systems - fig 4

Wedge mounting

HERTZ 301MP283 Mille Pro Car Audio Systems - fig 5

Suggested Length and Angle

MP 25.3 – MP 28.3 – MPK 130.3 – MPK 165.3 – MPK 165P.3 – MPK 1650.3

HERTZ 301MP283 Mille Pro Car Audio Systems - fig 6

Size

MP 70.3 – MPK 130.3 – MPK 165.3 – MPK 165P.3 – MPK 1650.3

HERTZ 301MP283 Mille Pro Car Audio Systems - fig 7

A| A 3| B| C| D| E| F| U| V|
---|---|---|---|---|---|---|---|---|---
MP 70 .3| 87,8| –| 73| 50| 44| 93| 17| 80| 3,7| mm
3.46| –| 2.87| 1.97| 1.73| 3.66| 0.67| 3.15| 0.15| in.
MP 130 .3| 130| 152| 114| 68| 57| 168,5| 29| 139| 5| mm
5.12| 5.98| 4.49| 2.68| 2.24| 6.63| 1.14| 5.47| 0.2| in
MP 165 .3| 165| –| 141| 74| 63| 183,5| 29| 156| 5| mm
6.5| –| 5.55| 2.91| 2.48| 7.22| 1.14| 6.14| 0.2| in.
MP 165P .3| 165| –| 141| 74,5| 64| 183,5| 29| 156| 5| mm
6.5| –| 5.55| 2.93| 2.52| 7.22| 1.14| 6.14| 0.2| in.
MPX 165 .3| 165| –| 141| 74| 62,2| 183,5| 29| 156| 5| mm
6.5| –| 5.55| 2.91| 2.46| 7.22| 1.14| 6.14| 0.2| in.

MPX 690.3

HERTZ 301MP283 Mille Pro Car Audio Systems - fig 9| HERTZ 301MP283 Mille Pro Car Audio Systems - fig 10
---|---
A 1| A 2| B 1| B 2| C| D| E 1| E 2| F| V|
---|---|---|---|---|---|---|---|---|---|---
MPX 690. 3| 241| 166| 223| 157| 108| 90| 267,5| 196| 38,5| 5 x7| mm
9.49| 6.54| 8.78| 6.18| 4.25| 3.54| 10.53| 7.72| 1.52| 0.2 x0.28| in.

Mounting

Option 1

HERTZ 301MP283 Mille Pro Car Audio Systems - fig 11

Option 2

HERTZ 301MP283 Mille Pro Car Audio Systems - fig12

Option 3

HERTZ 301MP283 Mille Pro Car Audio Systems - fig 13

Option 1

Option 2

Option 3

HERTZ 301MP283 Mille Pro Car Audio Systems - fig 16

MPCX 2.3 – MPCX 2P.3 – MPCX 3.3 – MPCX 165.3

HERTZ 301MP283 Mille Pro Car Audio Systems - fig 17

MPCX 2T.3

HERTZ 301MP283 Mille Pro Car Audio Systems - fig 18

G| H| I|
---|---|---|---
MPCX 2 .3| 102| 76,5| 37| mm
4.02| 3.01| 1.46| in.
MPCX 2P .3| 102| 76,5| 37| mm
4.02| 3.01| 1.46| in.
MPCX 2T .3| 72| 45,6| 23| mm
2.8| 1.8| 0.9| in.
MPCX 3 .3| 145,5| 114| 40| mm
5.73| 4.49| 1.57| in.
MPCX 165 .3| 145,5| 114| 40| mm
5.73| 4.49| 1.57| in.

HERTZ 301MP283 Mille Pro Car Audio Systems - fig18

Mounting

MPCX 3.3 – MPCX 165.3 MPCX 2.3 – MPCX 2P.3

HERTZ 301MP283 Mille Pro Car Audio Systems - fig 19| HERTZ 301MP283 Mille Pro Car Audio Systems - fig
20

Connecting the systems

MPK 130.3 – MPK 165.3 – MPK 165P.3

HERTZ 301MP283 Mille Pro Car Audio Systems - fig 21

Suggested crossover set-up

HERTZ 301MP283 Mille Pro Car Audio Systems - fig 22

MPK 1650.3 – SET-UP

HERTZ 301MP283 Mille Pro Car Audio Systems - fig 23

Suggested crossover set-up
MPCX 165.3

HERTZ 301MP283 Mille Pro Car Audio Systems - fig 24

MP 28.3

HERTZ 301MP283 Mille Pro Car Audio Systems - fig 25

PASSIVE set-up

HERTZ 301MP283 Mille Pro Car Audio Systems - fig 26

ACTIVE set-up

HERTZ 301MP283 Mille Pro Car Audio Systems - fig 27

Suggested active filtering:
A {MP 28.3: Hi-Pass @ 3,5 kHz – 12 dB Oct.)
B {Woofer: Lo-Pass @ 3∼4 kHz – 12 dB Oct.)

HERTZ 301MP283 Mille Pro Car Audio Systems - fig 28

MPK 163.3

A – MPK 163.3
Mid-Tweeter on A-Pillar| B – MPK 163.3
The midrange on the Door
---|---
|

MPCX 3.3

HERTZ 301MP283 Mille Pro Car Audio Systems - fig 31

Connections

HERTZ 301MP283 Mille Pro Car Audio Systems - fig 32

FREE AIR DC MP **25. 3 RES.| ****MP 28. 3| ****MP 70. 3| ****MP 165P. 3| MP 130.
MP 165. 3
MPX 165. 3| ****MPX 690. 3|
---|---|---|---|---|---|---
1 Speaker| 3,9| 3,3| 3,7| 2,6| 3,1| 3,0| Ω
2 Speaker
3 Speaker
4 Speaker| 7,8| 6,6| 7,4| 5,2| 6,4| 6,0| Ω
11,7| 9,9| 11,1| 7,8| 9,6| 9,0| Ω
15,6| 13,2| 14,8| 10,4| 12,8| 12,0| Ω
2 Speaker
3 Speaker
4 Speaker| 2,0| 1,7| 1,9| 1,3| 1,6| 1,5| Ω
1,3| 1,1| 1,2| 0,9| 1,1| 1,0| Ω
1,0| 0,8| 0,9| 0,7| 0,8| 0,8| Ω
4 Speaker
6 Speaker
8 Speaker**| 3,9| 3,3| 3,7| 2,6| 3,2| 3,0| Ω
2,6| 2,2| 2,5| 1,7| 2,1| 2,0| Ω
2,0| 1,6| 1,9| 1,3| 1,6| 1,5| Ω

Electro-Acoustic parameters

Component| Size| Power handling| Impedance| Frequency response
---|---|---|---|---
Peak| Continuous
mm (in.)| W| W| | Hz
MP 25. 3| Tweeter| Tweeter diaphragm 29 (1.14)| 120 (Hi-Pass filtered @ 2,5 kHz – 12 dB Oct.)| –| 4| 1.4k ÷ 22.5k
MP 28. 3| Tweeter| Tweeter diaphragm 35 (1.38)| 180 (Hi-Pass filtered @ 1,8 kHz – 12 dB Oct.)| –| 4| 1k ÷ 28k
MP 70. 3| Midrange| 70 (3)| 100 (Hi-Pass filtered @ 250 Hz – 12 dB Oct.)| –| 4| 180 ÷ 18k


MPX 165. 3

| ****

Two way coaxial

| Woofer 165 (6.5)| 200| 100| 4| 45 ÷ 21,5k
Tweeter diaphragm 25 (1)
MPX 690. 3| Three way coaxial| Woofer 6×9| 260| 130| 4| 30 ÷ 24k
Tweeter diaphragm 35 (1.5)
Super tweeter diaphragm 29 (1.14)
MPK 130. 3| Two way System| Woofer 130 (5)| 200| 100| 4| 60 ÷ 22,5k
Tweeter diaphragm 29 (1.14)
MPK 165. 3| Two way System| Woofer 165 (6.5)| 220| 110| 4| 40 ÷ 22,5k
Tweeter diaphragm 29 (1.14)
MPK 165P. 3| Two way System| Woofer 165 (6.5)| 230| 115| 3| 45 ÷ 22,5k
Tweeter diaphragm 29 (1.14)
MPK 163. 3| Three-way System| Woofer 165 (6.5)| 300| 150| 4| 40 ÷ 22,5k
Midrange 70 (3)
Tweeter diaphragm 29 (1.14)
MPK 1650. 3| Two way System| Woofer 165 (6.5)| 250| 125| 3| 45 ÷ 25k
Tweeter diaphragm 35 (1.38)
Magnet size| Voice coil | Magnet| Cone| Weight of one component
---|---|---|---|---
mm (in.)| mm (in.)| Kg (lb.)
24,5 x 6 x 3,5 (0.96 x 0.24 x 0.14)| 25 (1)| Neodymium| Teton| 0,065 (0.14)
27,8 x 3,5 x 3 (1.1 x 0.14 x 0.12)| 28 (1.1)| Neodymium| Teton| 0,075 (0.16)
16,8 x 2 (0.66 x 0.08) 19,7 x 5 (0.78 x 0.2)| 20 (0.8)| Neodymium| Pressed- pulp cone with cotton fiber| 0,17 (0.37)
90 x 45 x 17 (3.54 x 1.77 x 0.67)| 36 (1.42)| High-density flux ferrite| Pressed-pulp cone with cotton fiber| 1,27 (2.8)
107 x 45 x 20 (4.21 x 1.77 x 0.79)| 38 (1.5)| High-density flux ferrite| Pressed-pulp cone with cotton fiber| 2,28 (5.03)
85 x 32 x 17 (3.35 x 1.26 x 0.67)| | High-density flux ferrite| Pressed-pulp cone with cotton fiber| 0,95 (2.09)
24,5 x 6 x 3,5 (0.96 x 0.24 x 0.14)| 25 (1)| Neodymium| Teton| 0,07 (0.15)
85 x 32 x 17 (3.35 x 1.26 x 0.67)| 25 (1)| High-density flux ferrite| Pressed- pulp cone with cotton fiber| 1,07 (2.36)
24,5 x 6 x 3,5 (0.96 x 0.24 x 0.14)| 25 (1)| Neodymium| Teton| 0,07 (0.15)
95 x 45 x 17 (3.74 x 1.77 x 0.67)| 25 (1)| High-density flux ferrite| Pressed- pulp cone with cotton fiber| 1,2 (2.65)
24,5 x 6 x 3,5 (0.96 x 0.24 x 0.14)| 25 (1)| Neodymium| Teton| 0,07 (0.15)
85 x 32 x 17 (3.35 x 1.26 x 0.67)| 25 (1)| High-density flux ferrite| Pressed- pulp cone with cotton fiber| 1,07 (2.36)
16,8 x 2 (0.66 x 0.08) 19,7 x 5 (0.78 x 0.2)| 20 (0.8)| Neodymium| Pressed- pulp cone with cotton fiber| 0,17 (0.37)
24,5 x 6 x 3,5 (0.96 x 0.24 x 0.14)| 25 (1)| Neodymium| Teton| 0,07 (0.15)
95 x 45 x 17 (3.74 x 1.77 x 0.67)| 25 (1)| High-density flux ferrite| Pressed- pulp cone with cotton fiber| 1,2 (2.65)
27,8 x 3,5 x 3 (1.1 x 0.14 x 0.12)| 28 (1.1)| Neodymium| Teton| 0,075 (0.16)
Component| Specific component| Size| Crossover weight| Type – Cutoff
---|---|---|---|---
mm (in.)| Kg (lb.)
MPCX 2. 3| Crossover| MP 25.3
MP 130.3
MP 165.3| 102 x76,5 x37
(4.02 x3.01 x1.46)| 0,16
(0.35)| 3,5 kHz – 6/12 dB Oct Tweeter Level 0 /+2 dB
MPCX 2P. 3| Crossover| MP 25.3 MP 165P.3| 102 x76,5 x37
(4.02 x3.01 x1.46)| 0,17 (0.37)| 4 kHz – 6/12 dB Oct Tweeter Level 0 /+2.5 dB
MPCX 2T. 3| Crossover| MP 28.3| 72 x45,6 x33
(2.83 x1.8 x0.9)| 0,1 (0.22)| Tweeter Hi-Pass
3,5 kHz – 12 dB Oct Tweeter Level 0 /-2 dB
MPCX 3. 3| Crossover| MP 25.3
MP 70.3
MP 165.3| 145,5 x114 x40 (5.73 x4.49 x1.57)| 0,43 (0.94)| Woofer Lo- Pass 450 Hz – 6dB Oct Mid. Band-Pass 450 ÷ 5,5k Hz – 6dB Oct Tweeter Hi-Pass 5.5kHz – 12dB Oct Tweeter level 0 / +2 dB Midrange level 0 / +2 dB
MPCX 165. 3| Crossover| MP 28.3 MP 165P.3| 145,5 x114 x40 (5.73 x4.49 x1.57)| 0,37 (0.82)| Woofer Lo-Pass 12dB Oct Tweeter Hi-Pass 12dB Oct Tweeter level +2 / 0 / -2 dB Hi-Contour ON/OFF

Elektro-akoestische parameters

MP 25. 3| MP 28. 3| MP 70. 3| MP 130. 3| MP 165. 3| MP 165P. 3| MPX 165. 3| MPX 690. 3
---|---|---|---|---|---|---|---
D
mm| 29| 35| 65| 110| 132| 132| 132| 169
Xmax
mm| –| –| ±1,5| ±2,75| ±4| ±4,5| ±3| ±4
Re
Ω| 3,9| 3,3| 3,7| 3,1| 3,1| 2,6| 3,1| 3
Fs
Hz| 1200| 900| 110| 90| 70| 75| 90| 50
Le
mH| 0,02| 0,024| 0,12| 0,25| 0,3| 0,28| 0,01| 0,07
Vas
l| –| –| 1| 3| 9,5| 8| 4| 24
Mms
g| 0,17| 0,4| 2,9| 10,5| 14,9| 15,1| 18,9| 30
Cms
mm/N| 0,1| 0,08| 0,7| 0,24| 0,36| 0,3| 0,15| 0,34
BL
T•m| 1,6| 2| 2,8| 5,3| 5,5| 5,45| 5,8| 7,2
Qts| 0,55| 1,1| 0,82| 0,64| 0,58| 0,56| 0,88| 0,43
Qes| 1,98| 1,7| 1| 0,74| 0,67| 0,63| 1,06| 0,55
Qms| 0,57| 3,3| 4,6| 5,1| 4,6| 5,2| 5,5| 2
Spl
dB| 91| 91| 88| 92| 93| 94| 92| 94

HERTZ logoPART OF ELETTROMEDIA
Strada Regina Km 3,500 – Marignano
62018 Potenza Picena (MC) Italy
T +39 0733 870 870 – F +39 0733 870 880
www.elettromedia.it

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals