VOLT VAL-2014-X-XXX Fat Boy Mini Spotlight Instruction Manual

VOLT VAL-2014-X-XXX Fat Boy Mini Spotlight

IMPORTANT

This luminaire is intended for installation in accordance with local codes and the National Electric Code (NEC). Failure to adhere to these codes and instructions may result in serious injury, property damage and void the warranty.

These instructions do not intend to cover all variations in installation, operation maintenance or mounting situations.

1. Make sure that the power is turned OFF before installing or servicing this luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M) or more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply (transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with UL listed wire connectors that are suitable for outdoor use.
5. Position the low voltage wire and wire connector so that it is located within 6 inches (15.2 cm) from a building structure, a luminaire or fitting.
6. The main low voltage cable is intended for shallow burial – less than 6 inches (152 mm)

IMPORTANT SAFETY INSTRUCTIONS

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS Lighted lamp is HOT!

WARNING – TO REDUCE THE RISK OF FIRE OR INJURY TO PERSONS.

1. Turn off/unplug and allow to cool before replacing lamp.

2. Lamp gets HOT quickly! Contact only switch/plug when turning on.

3. Do not touch the hot lens, guard or enclosure.

4. Keep lamp away from materials that may burn.

5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may
   damage lamp.

6. Do not operate the luminaire fitting with a missing or damaged shield
   SAVE THESE INSTRUCTIONS

PACKAGE CONTENTS

A. (1) Fixture Body

PRODUCT DIMENSIONS

INSTALL STAKE

Determine the desired location for mounting the stake mount.
Hammer the stake into the ground until flange of stake is  flush to grade. To avoid damage to the stake, place a board on top of the stake while hammering.
Note: If the ground is hard and  the stake is difficult to install, make a crosscut in the ground  using a flat shovel.

INSTALL FIXTURE BODY TO STAKE

Clear away an area in the ground at the wireway slot on top of the stake. Lay the supply wires into the wireway slot and attach the fixture on to the stake. Tighten until snug.

Wire Connections

Strip both the leads from the luminaire pigtail. Using two UL listed wire connectors (sold separately), connect the leads from the luminaire to the main supply cable leads.

Remove Glare Guard and Lens

Loosen the set screw and remove the glare guard and lens from the fixture.

Install MR11 Bulb

Insert MR16 bulb with the correct wattage and type marked on the fixture label and secure into place
CAUTION: Do not exceed maximum wattage marked on luminaire label.

Install Lens

Place the lens and the glare guard back onto the fixture.
Align holes on both of them and secure with previously removed set screw. Hand tighten until snug.

Adjust Luminaire Direction

Loosen the adjustment screw at the joint and adjust the luminaire to the desired direction.
Once the desired direction is achieved, tighten the adjustment screw

Install/Replace Lamp

Remove the glare guard and the lens to expose the MR16 lamp and replace it with the correct wattage and type marked on the fixture label. Then, reinstall the lens and the glare guard.
IMPORTANT: MR16 lamp must be protected from moisture and dust at all times. Always reinstall the lens and the glare guard when removed.

CUSTOMER SUPPORT

Specifications and product details subject to change without notice.
© Copyright 2023, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
customersupport@voltlighting.com • www.voltlighting.com

References

• Factory Direct Landscape Lighting | VOLT® Lighting

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>