ANKER A2519 Wireless Memory Power Wave II Pad Instruction Manual
- June 13, 2024
- Anker
Table of Contents
ANKER A2519 Wireless Memory Power Wave II Pad
LED Indicator & Status
- Solid blue for 3 seconds, then off Connected to power
- Solid blue Charging mobile device
- Flashing blue Metal or abnormal objects detected
- Flashing green Loose connection Re-plug the adapter and try again
- You cannot charge your device wirelessly in these scenarios:
- using a case with a magnetic/iron plate;
- using a case with a pop socket;
- using an ultra-thick(> 5 mm) protective phone case.
- Do not place any foreign objects between your device and the wireless charger’s surface, including metal pads on a car mount, credit cards, door keys, coins, metal, or NFC cards, which will make wireless charging fail or cause overheating.
- Wireless chargers make charging more convenient than wired chargers, but confined by current wireless technology, their charging speed is slower than that of wired chargers.
- High temperatures will reduce charging speed and restrict power, which is a phenomenon common to all wireless chargers. It is recommended that you charge your device in environments with temperatures below 25°C / 77°F.
- Both the protective phone case and the position of your device on the wireless charger will affect the charging speed. The farther it is placed from the center of the wireless charger, the slower the charging speed will be.
Important Safety Instructions
- Avoid dropping.
- Do not disassemble.
- Do not expose to liquids.
- For the safest and fastest charge, use original or certified cables.
- This product is suitable for moderate climates only.
- The maximum ambient temperature during use of this product must not exceed 40°C.
- Open flame sources, such as candles, must not be placed on this product.
- Only use a dry cloth or brush to clean this product.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures: (1)
Reorient or relocate the receiving antenna. (2) Increase the separation
between the equipment and receiver. (3) Connect the equipment into an outlet
on a circuit different from that to which the receiver is connected. (4)
Consult the dealer or an experienced radio/ TV technician for help.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance of 20 cm between the radiator & your body.
The following importer is the responsible party (for FCC matters only). Company Name: Fantasia Trading LLC
Address: 9155 Archibald Avenue, Suite 20 2, Rancho Cucamonga, CA, 91730 ,
us
Telephone: + 1 (909) 484 1530
Product Name: PowerWave II Pad
Model: A2519
Anker Innovations Limited
Room 1318 -19 , Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong
IC Statement
This device complies with RSS-216 of Industry Canada. Operation is subject to
the condition that this device does not cause harmful interference.
This device complies with Industry Canada license-exempt RSS standard(s)
Operation is subject to the following two conditions: (1) This device may not
cause interference, and (2) This device must accept any interference,
including interference that may cause undesired operation of the device.
Specifications
Declaration of Conformity
Hereby, Anker Innovations Limited declares that the product type A2519 is in
compliance with Directives 2014/53/EU & 2011/65/EU. The full text of the EU
declaration of conformity is available at the following internet address:
https://www.anker.com/
ANKER
Charge Fast, Live More
For FAQs and more information, please visit:https://www.anker.com/support
Model: A2519 51005002051 V03
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>