VOLT LFL-2100-4-BBZ Bi-Pin Flood Light Instruction Manual

LFL-2100-4-BBZ Bi-Pin Flood Light
Instruction Manual

LFL-2100-4-BBZ Bi-Pin Flood Light

INSTALLATION INSTRUCTIONS
VOLT ® LOW VOLTAGE LANDSCAPE LIGHTING
V O LT ® Bi-Pin Flood Light
ITEM: LFL-2100-4-BBZ

IMPORTANT: PLEASE READ BEFORE INSTALLATION

This luminaire is intended for installation in accordance with local codes and the National Electric Code (NEC). Failure to adhere to these codes and instructions may result in serious injury, property damage and void the warranty.
These instructions do not intend to cover all variations in installation, operation maintenance or mounting situations.

1.  Make sure that the power is turned OFF before installing or servicing this fixture.
2. This fixture is perfect for placing in water fountains, water falls, ponds, pools, etc.
3. This fixture is intended to be used only with a power supply (transformer) rated maximum of 300 watts (25 AMPS) at 12 volts ~ 22 volts.
4. Underground Low Energy Cable must not be buried over 6” (15.2 cm) in order to connect to the main low voltage cable.
5. Wiring connections must be made with UL listed wire connectors that is suitable for outdoor use.
6. Position the wire connector so that it is located within 6 inches (15.2 cm) from a building structure, a luminaire, or fitting.

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
LIGHTED LAMP IS HOT!
WARNING – TO REDUCE THE RISK OF FIRE OR INJURY TO PERSONS.

1.  Turn off/unplug and allow to cool before reducing lamp.
2. Lamp gets HOT quickly!
3. Do not touch the hot lens, guard or cowl.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time.
6. Use a soft cloth.
7. Oil from skin may damage lamp.
   SAVE THESE INSTRUCTIONS

PACKAGE CONTENTS

A. (1) Fixture
B. (1) Stake
C. (1) Coupling
D. (1) G4 Bi-pin Lamp

PRODUCT DIMENSIONS

REMOVE GLARE GUARD AND DIFFUSER

By using a screwdriver, loosen the screws to remove the glare guard and the diffuser from the fixture body.

INSTALL G4 BULB

Insert G4 bulb with correct wattage and type marked on fixture label.
CAUTION: Do not exceed maximum wattage marked on luminaire label.

INSTALL GLARE GUARD AND DIFFUSER

Place the diffuser and the glare guard back onto the fixture body in turn. Secure by using the previously removed screws. Hand tighten until snug with a screwdriver.

INSTALL STAKE TO FIXTURE BODY

Place the coupling onto the yoke mount and thread it onto the stake. Hand tighten until snug with pliers or wrench.

INSTALL STAKE TO GROUND

Determine the desired location for mounting the stake. Insert the stake into the ground until flange of stake is flush to grade.

WIRE CONNECTIONS

Strip both leads from the fixture wires. Using two UL listed wire connectors (sold separately), connect the leads from the fixture wires to the main supply cable leads.

ADJUST FIXTURE BODY DIRECTION

Adjust the fixture body to the desired orientation.

After installation,
A. Check to make sure the fixture is mounted properly.
B. Check to make sure the wires are connected properly.
Last, turn on the power and check if the lighting fixture works. If not, turn off the power and contact your local electrician.

INSTALL/REPLACE G4 BULB

Please reverse Step 1 – Step 3 to expose the G4 bulb and replace it with the correct wattage and type marked on the fixture label. Then, reinstall the diffuser and the glare guard.
IMPORTANT: The G4 bulb must be protected from moisture and dust at all times. Always reinstall the diffuser and the glare guard when moved.

1-813-978-3700 • Mon-Fri 8am-8pm • Sat- Sun 10am – 6pm (EST)
Specifications and product details subject to change without notice.
© Copyright 2023, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
customersupport@voltlighting.com • www.voltlighting.com

References

• Factory Direct Landscape Lighting | VOLT® Lighting

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>