VOLT VPL-1043-4-BBK Wide Modernelle Brass Path and Area Light Instruction Manual
- June 13, 2024
- VOLT
Table of Contents
VOLT VPL-1043-4-BBK Wide Modernelle Brass Path and Area Light
Product Information
Product Name: VPL-1043-4-BBK Luminaire
Installation Instructions
- Make sure that the power is turned OFF before installing or servicing this luminaire.
- Warning: risk of electrical shock. Install all luminaires 10 feet (3.05M) or more from pool, spa or fountain.
- This luminaire is intended to be used only with a power supply (transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
- Wiring connections must be made with UL listed wire connectors that are suitable for outdoor use.
- Position the low voltage wire and wire connector so that it is located within 6 inches (15.2 cm) from a building structure, a luminaire or fitting.
- The main low voltage cable is intended for shallow burial – less than 6 inches (152 mm).
INSTALLATION INSTRUCTIONS
IMPORTANT: PLEASE READ BEFORE INSTALLATION
This luminaire is intended for installation in accordance with local codes and
the National Electric Code (NEC). Failure to adhere to these codes and
instruc-tions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
- Make sure that the power is turned OFF before installing or servicing this luminaire.
- Warning: risk of electrical shock. Install all luminaires 10 feet (3.05M) or more from pool, spa or fountain.
- This luminaire is intended to be used only with a power supply (transform-er) rated maximum of 300 watts (25 AMPS) at 15 volts.
- Wiring connections must be made with UL listed wire connectors that are suitable for outdoor use.
- Position the low voltage wire and wire connector so that it is located within 6 inches (15.2 cm) from a building structure, a luminaire or fitting.
- The main low voltage cable is intended for shallow burial – less than 6 inches (152 mm)
IMPORTANT SAFETY INSTRUCTIONS
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
LIGHTED LAMP IS HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
- Turn off/unplug and allow to cool before reducing lamp.
- Lamp gets HOT quickly!
- Do not touch the hot lens, guard or cowl.
- Keep lamp away from materials that may burn.
- Do not touch lamp at any time.
- Use a soft cloth.
- Oil from skin may damage lamp.
- Do not operate the fixture with a damaged or missing lens or shield
PACKAGE CONTENTS
A. (1) Fixture Body
PARTS REQUIRED (SOLD SEPARATELY)
A. (1) G4 Bi-Pin
PRODUCT DIMENSIONS
REMOVE LENS
Remove the lens from the fixture by loosening the screws.
Install G4 Bulb 
Insert the Bi-Pin with correct wattage and type marked on fixture label and push into place.
CAUTION
Do not exceed maximum wattage marked on luminaire label.
NOTE: DO NOT touch bulb with bare hands. Use soft cloth to handle bulb.
Install Lens
Place the lens back onto the fixture and secure with the previously removed screws. Tighten until snug.
Install Stake
Determine the desired location for mounting the stake mount. Hammer the stake
into the ground until flange of stake is flush to grade. To avoid damage to
the stake, place a board on top of the stake while hammering.
Note: If the ground is hard and the stake is difficult to install, make a
crosscut in the ground using a flat shovel.
INSTALL FIXTURE TO STAKE
Pass the fixture wire through the center hole of the stake. Thread the fixture on to the stake and hand tighten until snug.
WIRE CONNECTIONS 
Strip both leads from fixture body. Using two wire connectors (sold
separately), connect the leads from the fixture body to main supply cable
leads.
813.978.3700
INSTALL/ REPLACE G4 BULB
Please reverse Step 2 – Step 3 to expose the bi-pin and replace it with the correct wattage and type marked on the fixture label. And then reinstall the lens.
IMPORTANT
Bi-Pin must be protected from moisture and dust at all times. Always reinstall the lens when removed.
- 1-813-978-3700
- Mon-Fri 8am-8pm
- Sat-Sun 10am – 6pm (EST)
- Specifications and product details subject to change without notice.
- © Copyright 2023, VOLT® Lighting, Lutz FL USA 33549
- All rights reserved. customersupport@voltlighting.com
- www.voltlighting.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>