DAB-1199 Car Digital Radio Player Bt 4.2 Car Audio Player Instruction Manual

: June 13, 2024
: Dab

Table of Contents

RADDY SD10
Read User Manual Online (PDF format)
Download This Manual (PDF format)

RADDY SD10

CONTROLS

DAB-1199 Car Digital Radio Player Bt 4.2 Car Audio Player -
a1

reading lamp
solar panel
model(power)
Menu/Info
Scan/Select
Volume+
Volume-
Tune+
Tune-
Speaker
LCD Screen
charging indicator light
Rope Hole
Led Torch
SOS light
battery door
Power generator
Type c input
earphones jack
USB output
Antenna
torch button
reading lamp button
Sos button

INSTALLATION

ICONTENT OF DELIVERY

Main unit
Instruction Manual
USB-C cable
Hand strap

CHARGE BUILT-IN RECHARGEABLE BATTERY

with build in 3.7 V battery, long press the power button to switch on You have three ways to charge the built-in LI-ION battery.

1. Charge through USB socket

Connect a supplied USB cable to (DC IN 5V) USB type-C socket of the portable radio and 5V USB adaptor (not supplied).
Note: It takes approx. 6-8 hours to fully charge the battery.

2. Charge through sower generator (hand crank)

In emergency situation, you can charge the built-in battery through the power generator.
Pull out the POWER GENERATOR, then rotate it quickly.
The generated power is stored in the built-in battery.

Note:
The INPUT LED indicator (RED) will light.
Rotate the hand crank for 5 minutes to activate the built-in battery for initial use.

3. Charge through solar panel

It is difficult to fully charge the radio with solar panel, which mainly used for maintaining the built-in battery life.
Place solar panel directly under sunlight.

LED INDICATOR:

Function Charging indicator light
Wireless
Battery during INPUT charging RED

Note:
You can use the device while it is charging. However, this will increase the charging time.

INFORMATION ON RECHARGEABLE BATTERIES

Depending on environmental conditions, volume, etc., the playback time is approx. 6-8 hours (at 50% volume).
To preserve the rechargeable battery’s full capacity for as long as possible, you should fully recharge the battery every 2 to 3 months, even if you do not use the radio.
Charge the battery in an environment between 0°C and +40 °C.
The battery will best hold its charge at room temperature. The lower the surrounding temperature, the shorter the playback time.
The battery needs to be charged if the “flat” battery symbol ( ) appears in the display.

Note:
During battery recharge may affect to FM/DAB reception. SWITCHING THE DEVICE ON/OFF AND INTO STANDBY

Pull the telescopic antenna all the way out.
Press and hold the “ /MODE ” button until the device switches on.
To switch the device to standby, press and hold the “ /MODE ” button until the time and date appears in the display.
To switch the device on again from standby mode, press “ /MODE ” button once briefly.
To switch the device off totally from standby mode, press and hold the “ /MODE ” button until the display goes dark.

Note:
After approx. 15 minutes with no signal reception, the device will automatically switch to standby mode

SETTING THE VOLUME

Press “VOL +/-” button until the volume level appears in the display. Volume range: 0 to 32

SETTING THE LANGUAGE

To set the device to your language …

Press and hold “ MENU/INFO ” button to open system menu, select “ system ” and confirm with “ SCAN/SELECT “.
Press “ TUNE+/TUNE- ” until “ Language ” is shown and confirm with “ SCAN/SELECT “.
Press “ TUNE+/TUNE-“ until your desired language is shown and “ SCAN/SELECT “.

Note:
If you don’t press any button for a number of seconds then the display will revert back to the previously selected mode.
The settings that are not confirmed are not saved.

To quit the menu, briefly press the “ MENU/INFO ” button.

DAB

SELECTING THE OPERATING MODE

Briefly press the “ /MODE ” button repeatedly to switch between the DAB, FM radio and Wireless modes.

TUNING IN DAB MODE

Switching to DAB mode will automatically retrieve the station last selected.

Briefly press “ TUNE+/TUNE- ” . The full list of stations will open.
Use “ TUNE+/TUNE- ” to select the desired station and confirm with “ SCAN/SELECT “.

Note:

You will also find the complete list of stations in the system menu under “ Station List “. Here you can also start a full manual “ Scan “
You can select specific frequencies/frequency blocks under “ Manual Tune ” in the system menu.
The signal strength of the chosen frequency block will be shown as bars on the display.
There are no setting options. Press “ MENU/INFO ” button to quit the system menu.
Not all stations are on the air at all times; many that were once on the air have since disappeared; or you have received stations in another region that you can no longer receive in your new location: To clean up the station list, you can remove these stations in the system menu with “ Prune “.
Press “ MENU/INFO ” repeatedly to view different information about the station, the music etc., depending on the station.

SAVING STATIONS (PRESET STORE). IN DAB

Set the station that you wish to save.
Press and hold “ MENU/INFO ” button to open system menu, select “ system ” and confirm with “ SCAN/SELECT “.
Use “ TUNE+/TUNE- ” to select “Preset Store” and confirm with “ SCAN/SELECT “.
Use “ TUNE+/TUNE- ” to select the desired memory preset and confirm with “ SCAN/SELECT “. “ Preset (number) stored ” appears briefly in the display which then returns to the DAB or FM mode.

Note:
You have a choice of 40 memory presets.

CALLING UP SAVED STATIONS (PRESET RECALL) IN DAB

Press and hold “ MENU/INFO ” button to open system menu, select “ Preset Recall ” and confirm with “ SCAN/SELECT “.
Use “ TUNE+/TUNE- ” to select the desired station and confirm with “ SCAN/SELECT “.

The display will jump back to DAB+ or FM mode. Memory “ P01 ” will be shown on the display.

FM

SELECTING THE OPERATING MODE

Briefly press the “MODE” button repeatedly to switch between the DAB, FM radio and Wireless modes.

TUNING IN FM MODE

Switching to FM mode will automatically retrieve the station last selected. If that station cannot be received at that time press “ SCAN/SELECT ” button to search for the next station which can be received.
Briefly press “ TUNE+/TUNE- ” to search for a station in 0.05 MHz steps. Press and hold “ TUNE+/TUNE- ” to start a station scan.
The scan stops once the first receivable station is located.
In the system menu under “ Scan Setting ” you can select whether “ All Stations ” or only “ Strong Stations ” will be included.

SAVING STATIONS (PRESET STORE). IN FM

Same as “ DAB ”

CALLING UP SAVED STATIONS (PRESET RECALL) IN FM

Same as “ DAB ”

Wireless/BT

In the Wireless mode you can connect your Wireless-enabled mobile device and play saved music files via the radio.

Note: Always refer to the instruction manual for your mobile device. The device cannot connect to a Wireless speaker or headphones

ESTABLISHING A CONNECTION

Switch on the Wireless function on your mobile device.

Briefly press the “ /MODE ” button to select the Wireless mode.
The display shows Disconnected flash while the device is searching for a Wireless signal.
The Wireless LED indicator will light up in blue.
Start the device scan on your mobile device.
Select “ SD10 ” on your mobile device and connect the devices as usual.

PLAYING MUSIC

The radio can play music in all conventional file formats supported by your mobile device.

First start playback on your mobile device.
You can also perform these functions directly on the DAB radio:
Press “ SCAN/SELECT ” to start and pause playback.
To return to the start of the track or to skip to the previous track, press once or twice.
Skip to the next track with.
Press the VOL +/- button to adjust the volume.
Note: If the volume is too low, adjust it on your mobile device.

DISCONNECTING THE DEVICE

There can only be one device connected to the radio via Wireless at any time. If you would like to connect another device, you must first disconnect the current device. Proceed as follows:

Unpair the devices on your mobile device.
The devices will also unpair if you move them outside the Wireless range.
Note: If you switch off the radio, it will automatically connect with the Wireless « device again once it is switched back on, provided it is close by and switched on and the Wireless function is activated

USING HEADPHONES

Listening to music at a high volume on a regular basis can lead to hearing damage. Set the volume to a low setting before starting to play music through the radio. Then you can set the volume higher if you want.

Lower the volume.
Use a 3.5mm jack plug to connect an earphone or headphone to the headphone port.
If necessary, increase the volume. This mutes playback via the speaker.

Note: Earphone with line-control is not compatible to this radio.

ALARM AND SLEEP FUNCTION

ALARM FUNCTION

Here you can preselect a time for the device to wake you.

Press and hold “ MENU/INFO ” button to open system menu, select “system” and confirm with “ SCAN/SELECT “.
Use “ TUNE+/TUNE- ” to select Alarms and confirm with “ SCAN/SELECT “.
Use “ TUNE+/TUNE- ” to select Alarm 1 or Alarm 2 and confirm with “ OK “.
Use “TUNE+/TUNE-” to select Alarm and use “ SCAN/SELECT ” to switch between On and Off.
Use “ TUNE+/TUNE- ” to select Time and confirm with “ SCAN/SELECT “.
Use “ TUNE+/TUNE- ” and to set the hour and the minute, then confirm each with “ SCAN/SELECT “.
Use “ TUNE+/TUNE- ” to select Source and confirm with “ SCAN/SELECT “.
Use “ TUNE+/TUNE- ” to select between FM, DAB and Buzzer and confirm with “ SCAN/SELECT “.
Use “ TUNE+/TUNE- ” to select Repeat and confirm with “ SCAN/SELECT “.
Use “ TUNE+/TUNE- ” to select between Once, Daily, Weekends and Workday and confirm with “ SCAN/SELECT “.
Use “ TUNE+/TUNE- ” to select Volume and confirm with “SCAN/SELECT”.
Use “ TUNE+/TUNE- ” to select duration and confirm with “ SCAN/SELECT “.
Quit the menu with “ MENU/INFO ” button.
The alarm symbol 1 or 2 lights up in the display.
Switch the device to standby with” /MODE ” if necessary. The selected alarm signal will sound at the set time.

Press any button to snooze the alarm 5 minutes. (Except Flash light and SOS buttons)
Display will show snooze timing counter.
Press “ /MODE ” to deactivate the alarm signal completely.

SLEEP FUNCTION

Here you can pre-select a time after which the device switches off automatically.

Press and hold “ MENU/INFO ” button to open the system menu, select “system” and confirm with “ SCAN/SELECT “.
Use “ TUNE+/TUNE- ” to select Sleep and confirm with “ SCAN/SELECT “.
Use “ TUNE+/TUNE- ” to select between 15 > 30 > 45 > 60 > 75 > 90 minutes and Off.
Briefly press “ SCAN/SELECT ” to confirm.
The display shows “ SXX ” and “ XX ” means remaining sleep time.

SYSTEM SETTINGS

SETTING THE TIME/DATE MANUALLY

If you do not have any DAB reception, you can also configure the time and date manually.

Press and hold the “ MENU/INFO ” button to open the system menu, select “system” and confirm with “ SCAN/SELECT “.
Use “ TUNE+/TUNE- ” to select “ Time/Date ” and confirm with “ SCAN/SELECT “.
Use “ TUNE+/TUNE- ” to select “ Set Time/Date ” and confirm with “ SCAN/SELECT “.
Use “ TUNE+/TUNE- ” to set Day – Month – Year – Hour – Minute one by one and confirm each with “ SCAN/SELECT “. The display will automatically jump one step back in the menu.
Use “ TUNE+/TUNE- ” to select “ Set Hour System ” and confirm with “ SCAN/SELECT “.
Use “ TUNE+/TUNE- ” to select “ 24 hour system ” or “ 12 hour system ” and confirm with “ SCAN/SELECT “. The display will automatically jump one step back in the menu.
Use “ TUNE+/TUNE- ” to select “Set Date Format” and confirm with “ SCAN/SELECT “.
Use “ TUNE+/TUNE- ” to toggle between dd-mm-yyyy, mm-dd-yyyy and yyyy-mm-dd, and confirm with “ SCAN/SELECT “. The display will automatically jump one step back in the menu.
Use “TUNE+/TUNE-” to select “Auto. Update” and confirm with “ SCAN/SELECT “.
Use “ TUNE+/TUNE- ” to select between “ No Update ” and “ Update from Radio ” (the DAB+ station will set the time automatically if reception is good enough) and confirm with “ SCAN/SELECT “.
The display will automatically jump one step back in the menu.

SETTING THE DISPLAY BACKLIGHT

Press and hold “ MENU/INFO ” button to open the system menu, select “system” and confirm with “ SCAN/SELECT “.
Use “ TUNE+/TUNE- ” to select “ Backlight ” and confirm with “ SCAN/SELECT “.
Use “ TUNE+/TUNE- ” to select “ Timeout ” and confirm with “ SCAN/SELECT “.
Use “ TUNE+/TUNE- ” to select between “ Always On ” and a switch-off time for the lighting between 10 and 180 seconds and confirm with “ SCAN/SELECT “.
The display will automatically jump one step back in the menu.
Use “ TUNE+/TUNE- ” to select Level and confirm with “ SCAN/SELECT “.
Use “TUNE+/TUNE-” to select the brightness of the display between Low, Medium, High and confirm with “ SCAN/SELECT “.
The display will automatically jump one step back in the menu.

RESTORING FACTORY SETTINGS

Press and hold the “ MENU/INFO ” button to open the system menu, select “ system ” and confirm with “ SCAN/SELECT “.
Use “ TUNE+/TUNE- ” to select “Factory Reset” and confirm with “ SCAN/SELECT “.
Use “ TUNE+/TUNE- ” to select “ No ” or “ Yes ” and confirm with “ SCAN/SELECT “.

SOFTWARE VERSION

Here you can view the software version installed.

Press and hold the “ MENU/INFO ” button to open the system menu, select “ system ” and confirm with “ SCAN/SELECT “.
Use “ TUNE+/TUNE- ” to select “ System Version ” and confirm with “ SCAN/SELECT “.
The currently installed software version is displayed.
Press “ MENU/INFO ” to quit the menu item

LIGHT

TURN THE FLASHLIGHT ON (3 MODES)

During operation, briefly press “ ” button to select different light mode.
During OFF mode, press and hold “ ” to enable flashlight.

TURN THE READING LIGHT ON

Press “ ” The button to adjust the light mode
Flip up the solar panel the reading light will auto switch ON or OFF by closing the solar panel.

USB OUT 5V

This portable radio can also serve as an emergency charger for your mobile phone. Do not use it as a normal power bank.
Note: Emergency Charger is only available in Standby or OFF mode

Open the USB rubber cover
Plug your mobile phone charging cable (not supplied) into USB OUT 5V socket, then plug into your phone.

Turn the SOS/ALERT on

Press and hold the “SOS” button on front panel to enable alarm sound.

Briefly press SOS button to select different mode.
The very loud alarm sound on and flashlight will keep flashing.

Problems / solutions

Not working

Is the battery flat?
Is the mains adapter connected?

No sound

Have you selected the correct mode of operation?
Is the volume set too low?
Are there headphones connected?

DAB: the station selected has no signal
FM: The audio signal is weak or poor in quality.

Are any other devices, e.g.: microwave, motor, mixer, television interfering with the signal?
Is the radio signal too weak?
FM mode audio setting to Mono only.
Check the signal strength in DAB mode.
Adjust the position of the antenna or move the device to another location.
Disconnect USB-C input cable.
Disconnect USB output cable.

14: Technical parameters

Frequency range| FM:87.5-108 MHZ
DAB:170-240 MHZ
---|---
Sensitivity| FM 8dB
Signal to noise ratio| FM 38 dB
Max current| 680mA
Quiescent current| 160uA
Output current for external charging| 800mA
Working voltage| 3.5V-4.2V
Max power consumption| 1.3W
Product size| 164.2×62.5x94MM
Net weight| 507g