VOLT VUL-704 Salty Dog Brass MR16 Underwater Light Instruction Manual

VOLT VUL-704 Salty Dog Brass MR16 Underwater Light

Product Information

• This product is a luminaire designed for installation in accordance with local codes and the National Electric Code (NEC).
• It is intended for outdoor use and should be installed with a power supply (transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
• The luminaire comes with a faceplate, gasket, lens, MR16 lamp, mounting screws, flat washers, anchors, and a horseshoe mount.
• The maximum wattage for the lamp should not be exceeded.
• The luminaire has a low voltage cable that is intended for shallow burial of less than 6 inches (152 mm).

Product Usage Instructions

1. Before installing or servicing the luminaire, ensure that the power is turned OFF.
2. Install all luminaires at least 10 feet (3.05M) away from pools, spas, or fountains to avoid the risk of electrical shock.
3. Ensure that the power supply (transformer) used is suitable for the luminaire’s maximum rating.
4. Make wiring connections using UL listed wire connectors suitable for outdoor use.
5. Position the low voltage wire and wire connector within 6 inches (15.2 cm) from a building structure, luminaire, or fitting.
6. To install the luminaire:
7. Remove the faceplate, gasket, and lens by unscrewing the screws.
8. Insert the correct wattage and type of lamp marked on the fixture label into the socket. Do not exceed the maximum wattage.
9. Secure the lens, gasket, and faceplate back onto the housing using the previously removed screws. Tighten them completely using a screwdriver in a star pattern.
10. Attach the horseshoe mount to the desired location and mark 3 points for anchors from the holes on the mount.
11. Drill proper holes on the marked locations and insert the anchors. Attach the horseshoe mount onto the anchors using washers and mounting screws. Tighten them with a screwdriver.
12. Strip both leads from the luminaire pigtail and connect them to the main supply cable leads using wire connectors.
13. Adjust the housing to your desired direction using the thumb screws on the side of the housing.
14. To install/replace the glare guard:
15. Remove the faceplate from the housing.
16. Attach or replace the glare guard as needed.
17. Secure the faceplate back onto the housing using screws.

IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT: PLEASE READ BEFORE INSTALLATION
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and instructions may result in serious injury, property damage and void the warranty.
These instructions do not intend to cover all variations in installation, operation maintenance or mounting situations.

• Make sure that the power is turned OFF before installing or servicing this luminaire.
• WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M) or more from pool, spa or fountain.
• This luminaire is intended to be used only with a power supply (transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
• Wiring connections must be made with UL listed wire connectors that are suitable for outdoor use.
• Position the low voltage wire and wire connector so that it is located within 6 inches (15.2 cm) from a building structure, a luminaire or fitting.
• The main low voltage cable is intended for shallow burial – less than 6 inches (152 mm)

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS LIGHTED LAMP IS HOT!

WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.

• Turn off/unplug and allow to cool before reducing lamp.
• Lamp gets HOT quickly!
• Do not touch the hot lens, guard or cowl.
• Keep lamp away from materials that may burn.
• Do not touch lamp at any time.
• Use a soft cloth.
• Oil from skin may damage lamp.
• Do not operate the fixture with a damaged or missing lens or shield.

PACKAGE CONTENTS

• (1) Fixture

Parts Required (sold separately/not provided)

• (3) Mounting Screws
• (3) Flat Washers
• (3) Anchors
• (1) MR16 Lamp

PRODUCT DIMENSIONS

Remove Faceplate and Lens

Unscrew the screws and remove the faceplate, gasket and lens from the housing.

Install/Replace Lamp

Insert the lamp with the correct wattage and type marked on the fixture label.
CAUTION: Do not exceed maximum wattage marked on luminaire label.
NOTE: DO NOT touch lamp with bare hands. Use soft cloth to handle lamp.

Install Lens and Faceplate

Place the lens, gasket and faceplate back onto the housing. Secure them with the screws previously removed. Hand tighten until snug. Then, use a screwdriver moving in a star pattern to secure them completely.

Install Horseshoe Mount

Attach the horseshoe mount on your desired location and mark (3) points for anchors from the holes on the horseshoe mount.
Drill proper holes on the location and insert the anchors into the drilled holes. Attach the horseshoe mount onto the anchors. Pass the washers over the mounting screws and thread the mounting screws into the anchors to secure the horseshoe mount. Hand tighten until snug with a screwdriver.
NOTE: SOME APPLICATIONS ARE NOT SUITABLE FOR PERMANENT MOUNTING AND DO NOT REQUIRE OR WARRANT THE USE OF SCREWS AND ANCHORS

Wire Connection

Strip both leads from the luminaire pigtail. Using two wire connectors (sold separately), connect the leads from the luminaire to the main supply cable leads.
Adjust the housing to your desired direction by using thumb screws on the side of the housing.

Remove Faceplate

Unscrew the screws on ring and remove the faceplate from the housing.

Install Glare Guard

Install the glare guard onto housing and secure with screws previously removed by using a star pattern to tighten them.

1-813-978-3700 • Mon-Fri 8am-8pm • Sat- Sun 10am – 6pm (EST)
Specifications and product details subject to change without notice.
© Copyright 2023, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved. customersupport@voltlighting.com • www.voltlighting.com

References

• Factory Direct Landscape Lighting | VOLT® Lighting

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>