VFL-4520-BBZ Low Voltage Landscape Lighting Instruction Manual
- June 13, 2024
- VOLT
Table of Contents
VFL-4520-BBZ Low Voltage Landscape Lighting
Product Information
- This luminaire is designed for installation in accordance with local codes and the National Electric Code (NEC).
- Failure to follow the codes and instructions may result in serious injury, property damage, and void the warranty.
- The luminaire is intended for use with a power supply (transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
- UL-listed wire connectors suitable for outdoor use must be used for wiring connections.
- The low-voltage wire and wire connector should be positioned within 6 inches (15.2 cm) from a building structure, a luminaire, or fitting.
- The main low-voltage cable is suitable for shallow burial, less than 6 inches (152 mm).
- If additional lengths of low-voltage cable are required, contact www.voltlighting.com or call 1-813-978-3700.
- Caution: The lighted lamp is hot and can cause a risk of fire or injury to persons.
Product Usage Instructions
Install Stake:
- Determine the desired location for mounting the stake mount.
- Hammer the stake into the ground until the flange of the stake\ is flush to grade.
- To avoid damage to the stake, place a board on top of the stake while hammering.
- Note: If the ground is hard and the stake is difficult to install, make a crosscut in the ground using a flat shovel.
Install Lamp:
- Use a PAR36 lamp (sold separately) with the correct wattage and type as marked on the luminaire label.
- Connect supply wires to screws on the bottom of the lamp and tighten until snug with a screwdriver.
- Push the lamp into the lamp holder and seat it in place.
- Caution: Do not exceed the maximum wattage marked on the luminaire label.
- Note : Do not touch the lamp with bare hands. Use a soft cloth to handle the lamp.
Install Lens:
- Align the locking parts on both the lens and fixture body.
- Position the lens so that when it turns, it locks properly into place.
Install Fixture to Stake:
- Clear away an area in the ground at the wireway slot on top of the stake.
- Lay the luminaire pigtail into the wireway slot and secure the fixture onto the stake.
- Tighten until snug.
Wire Connection:
- Strip both leads from the luminaire pigtail.
- Using two wire connectors (sold separately), connect the leads from the luminaire to the main low voltage supply cable leads.
Install/Replace Lamp:
- To expose the lamp, reverse Step 2 – Step 3.
- Replace the lamp with the correct wattage and type marked on the luminaire label.
- Important: Halogen lamps must be protected from moisture and dust at all times. Always reinstall the lens when removed.
VOLT® Big Par36 Brass Bronze Flood
ITEM: VFL-4520-BBZ
INSTALLATION INSTRUCTIONS
IMPORTANT : PLEASE READ BEFORE INSTALLATION
This luminaire is intended for installation in accordance with local codes and
the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations
- Make sure that the power is turned OFF before installing or servicing this luminaire.
- WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M) or more from pool, spa or fountain.
- This luminaire is intended to be used only with a power supply (transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
- Wiring connections must be made with UL listed wire connectors that are suitable for outdoor use.
- Position the low voltage wire and wire connector so that it is located within 6 inches (15.2 cm) from a building structure, a luminaire or fitting.
- The main low voltage cable is intended for shallow burial – less than 6 inches (152 mm).
- If additional lengths of low voltage cable is required, please contact www.voltlighting.com or call 1-813-978-3700.
IMPORTANT SAFETY INSTRUCTIONS
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS LIGHTED LAMP IS HOT!
- WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
- Turn off/unplug and allow to cool before reducing lamp.
- Lamp gets HOT quickly!
- Do not touch the hot lens, guard or cowl.
- Keep lamp away from materials that may burn.
- Do not touch lamp at any time.
- Use a soft cloth.
- Oil from skin may damage lamp.
- Do not operate the fixture with a damaged or missing lens or shield
PACKAGE CONTENTS
- A. (1) Fixture
- B. (1) Stake
PRODUCT DIMENSIONS
INSTALL STAKE
- Determine the desired location for mounting the stake mount. Hammer the stake into the ground until the flange of the stake is flush to grade. To avoid damage to the stake, place a board on top of the stake while hammering.
Note : If the ground is hard and the stake is difficult to install, make a crosscut in the ground using a flat shovel.
INSTALL LAMP
- Use a PAR36 lamp (sold separately), with the correct wattage and type as marked on the luminaire label.
- Connect supply wires to screws on the bottom of the lamp, and tighten until snug with a screwdriver. Push the lamp into the lamp holder and seat in place.
- CAUTION: Do not exceed the maximum wattage marked on the luminaire label.
- NOTE: DO NOT touch the lamp with bare hands. Use a soft cloth to handle the lamp.
Install Lens
Install the lens to the fixture body by aligning the locking parts on both of them. Be sure to position the lens so when it turns it locks properly into place.
Install Fixture to Stake
Clear away an area in the ground at the wireway slot on top of the stake. Lay luminaire pigtail into the wireway slot and secure the fixture onto the stake. Tighten until snug
Wire Connection
Strip both leads from the luminaire pigtail. Using two wire connectors (sold separately), connect the leads from the luminaire to the main low voltage supply cable leads.
INSTALL/REPLACE LAMP
- Reverse Step 2 – Step 3 to expose the lamp and replace it with the correct wattage and type marked on the luminaire label.
- IMPORTANT : Halogen lamps must be protected from moisture and dust at all times. Always reinstall the lens when removed
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-
Sun 10am – 6pm (EST)
Specifications and product details subject to change without notice.
© Copyright 2023, VOLT® Lighting, Lutz FL USA 33549
All rights reserved.
customersupport@voltlighting.com
www.voltlighting.com
References
- Factory Direct Landscape Lighting | VOLT® Lighting
- Factory Direct Landscape Lighting | VOLT® Lighting
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>