Vantron VT-MITX-TGL Single Board Computer User Manual
- June 13, 2024
- Vantron
Table of Contents
VT-MITX-TGL Single Board Computer
Product Information: Product Name: VT-MITX-TGL Single Board
Computer Product Version: 1.3 Manufacturer: Vantron Website:
www.vantrontech.com Product Usage Instructions: 1. Foreword: Thank
you for purchasing the VT-MITX-TGL single board computer. This user
manual provides guidance and assistance on setting up, operating,
and maintaining the product. It is important to read this manual
and understand the functionality of the product before using it. 2.
Intended Users: This product is designed for individuals who
require a single board computer for embedded/IoT applications. 3.
Copyright: All information in this manual is copyrighted by
Vantron. It is prohibited to reproduce, distribute, or modify any
part of this manual without prior written permission from Vantron.
4. Disclaimer: Vantron takes no responsibility for any errors or
features mentioned in this manual. Improper use of the manual or
the software may result in damage to the product. Vantron reserves
the right to change specifications without notice. 5. Technical
Support and Assistance: If you require technical support or
assistance with the VT-MITX-TGL single board computer, please
contact Vantron through their website www.vantrontech.com. Please
refer to the complete user manual for detailed instructions on
setting up, operating, and maintaining the VT-MITX-TGL single board
computer.
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
VT-MITX-TGL Single Board Computer
User Manual
Version: 1.3
VT-MITX-TGL | User Manual
© Vantron Technology, Inc. All rights reserved.
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
Revision History
No.
Version
Description
Date
1
V1.0
First release
Jul. 21, 2022
2
V1.1
Updated interface figures
Nov. 19, 2022
3
V1.2
Updated I2C description as per the upgraded device May 22, 2023
4
V1.3
Added the debugging of the UART and GPIO
Aug. 30, 2023
VT-MITX-TGL | User Manual
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
Table of Contents
Foreword ……………………………………………………………………………………………………………………….. 1 CHAPTER 1
INTRODUCTION …………………………………………………………………………………………….. 5
1.1 Product Overview ……………………………………………………………………………………………… 6 1.2
Terminology/Acronym ……………………………………………………………………………………….. 6 1.3 Block Diagram
…………………………………………………………………………………………………… 7 1.4 Specifications
……………………………………………………………………………………………………. 8 1.5 Operating System
……………………………………………………………………………………………… 9 1.6 Mechanical
Dimensions……………………………………………………………………………………… 9 1.7 Power Supply and
Consumption………………………………………………………………………….. 9 1.8 Environmental Specifications
……………………………………………………………………………… 9 CHAPTER 2 CONNECTORS AND PIN ASSIGNMENT
…………………………………………………………….. 10
2.1 Product Layout………………………………………………………………………………………………… 11 2.2 System
Configurations ……………………………………………………………………………………… 11 2.2.1 CPU
……………………………………………………………………………………………………………….. 11 2.2.2 Memory
…………………………………………………………………………………………………………. 11 2.2.3
Storage…………………………………………………………………………………………………………… 11 2.3 Connectors and
jumpers…………………………………………………………………………………… 12 2.3.1 J8/J4 Power input (1)
……………………………………………………………………………………….. 12 2.3.2 J20/J23 Ethernet ports (2)
………………………………………………………………………………… 13 2.3.3 J7 eDP connector
(3)………………………………………………………………………………………… 13 2.3.4 J19 LVDS/eDP connector (4)
……………………………………………………………………………… 15 2.3.5 J27 Backlight connector
(5)……………………………………………………………………………….. 16 2.3.6 J10 DP (6)
……………………………………………………………………………………………………….. 17 2.3.7 J11 HDMI (7)
…………………………………………………………………………………………………… 18 2.3.8 J52/J53 RS232
(8)…………………………………………………………………………………………….. 19 2.3.9 J50/J51 RS232/RS422/RS485
(9)…………………………………………………………………………20 2.3.10 J49 Front panel connector
(10)…………………………………………………………………………..21 2.3.11 J32/J37/J38 USB 2.0 connectors
(11)…………………………………………………………………..22 2.3.12 J16 USB 3.0 Type-A (12)
……………………………………………………………………………………. 23 2.3.13 J18 USB 2.0 Type-A (13)
……………………………………………………………………………………. 23 2.3.14 J15 USB 3.1 Type-C (14)
……………………………………………………………………………………. 23 2.3.15 J54 SATA connector (15)
…………………………………………………………………………………… 24 2.3.16 J48 SATA power connector (16)
…………………………………………………………………………. 24 2.3.17 J56 Audio jacks (17)
…………………………………………………………………………………………. 24 2.3.18 J25 F_AUDIO connector (18)
…………………………………………………………………………….. 25 2.3.19 J46/J47 Speaker connectors (19)
……………………………………………………………………….. 26 2.3.20 J14 M.2 M-Key
(20)………………………………………………………………………………………….. 26 2.3.21 J24 M.2 B-Key (21)
…………………………………………………………………………………………… 26 2.3.22 J21 M.2 E-Key (22)
…………………………………………………………………………………………… 26 2.3.23 J31/J34 GPIO (23)
……………………………………………………………………………………………. 27 2.3.24 J29 GPIO power (24)
………………………………………………………………………………………… 28 2.3.25 J9 I2C (25)
……………………………………………………………………………………………………….. 28
VT-MITX-TGL | User Manual
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
2.3.26 J12/J13 DDR4 SO-DIMM Sockets (26)………………………………………………………………….29 2.3.27
J5/J6 Fan Connectors (27)…………………………………………………………………………………. 29 CHAPTER 3 FIRST-
USE DEBUGGING …………………………………………………………………………………. 30
3.1 Driver Introduction ………………………………………………………………………………………….. 31 3.2 Serial
Port Setup ……………………………………………………………………………………………… 32 3.3 GPIO
Setup……………………………………………………………………………………………………… 33 CHAPTER 4 BIOS AND
WINDOWS……………………………………………………………………………………. 35
4.1 BIOS Introduction ……………………………………………………………………………………………. 36 4.2 BIOS Setup
……………………………………………………………………………………………………… 36 4.2.1 Entering BIOS Setup Utility
……………………………………………………………………………….. 36 4.2.2 Selecting a Boot Option
……………………………………………………………………………………. 37 4.3 Windows 10 System Upgrade
……………………………………………………………………………. 38 4.3.1 Prerequisites
…………………………………………………………………………………………………… 38 4.3.2 Making a Bootable USB Drive
for Windows 10…………………………………………………….. 38 4.3.3 Installing Windows
10………………………………………………………………………………………. 39 CHAPTER 5 DISPOSAL AND WARRANTY
…………………………………………………………………………… 40
5.1 Disposal …………………………………………………………………………………………………………. 41 5.2 Warranty
………………………………………………………………………………………………………… 42
VT-MITX-TGL | User Manual
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
Foreword
Thank you for purchasing VT-MITX-TGL single board computer (“the Board” or
“the Product”). This manual intends to provide guidance and assistance
necessary on setting up, operating or maintaining the Product. Please read
this manual and make sure you understand the functionality of the Product
before putting it into use.
Intended Users
This manual is intended for: · Embedded software developer · Custom
development software engineer · Other technically qualified personnel
Copyright
Vantron Technology, Inc. (“Vantron”) reserves all rights of this manual,
including the right to change the content, form, product features, and
specifications contained herein at any time without prior notice. An up-to-
date version of this manual is available at www.vantrontech.com. The
trademarks in this manual, registered or not, are properties of their
respective owners. Under no circumstances shall any part of this user manual
be copied, reproduced, translated, or sold. This manual is not intended to be
altered or used for other purposes unless otherwise permitted in writing by
Vantron. Vantron reserves the right of all publicly released copies of this
manual.
Disclaimer
While all information contained herein has been carefully checked to assure
its accuracy in technical details and typography, Vantron does not assume any
responsibility resulting from any error or features of this manual, nor from
improper uses of this manual or the software. It is our practice to change
part numbers when published ratings or features are changed, or when
significant construction changes are made. However, some specifications of the
Product may be changed without notice.
VT-MITX-TGL | User Manual
1
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
Technical Support and Assistance
Should you have any question about the Product that is not covered in this
manual, contact your sales representative for solution. Please include the
following information in your question: · Product Signal and PO number; ·
Complete description of the problem; · Error message you received, if any.
Vantron Technology, Inc.
Address: 48434 Milmont Drive, Fremont, CA 94538 Tel:
650-422-3128 Email:
sales@vantrontech.com
Symbology
This manual uses the following signs to prompt users to pay special attention
to relevant information.
Caution for latent damage to system or harm to personnel Attention to
important information or regulations
VT-MITX-TGL | User Manual
2
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
General Safety Instructions
The Product is supposed be installed by knowledgeable, skilled persons
familiar with local and/or international electrical codes and regulations. For
your safety and prevention of damage to the Product, please read and observe
carefully the following safety instructions prior to installation and
operation. Keep this manual well for future reference. · Do not disassemble or
otherwise modify the Product. Such action may cause heat
generation, ignition, electronic shock, or other damages including human
injury, and may void your warranty. · Keep the Product away from heat source,
such as heater, heat dissipater, or engine casing. · Do not insert foreign
materials into any opening of the Product as it may cause the Product to
malfunction or burn out. · To ensure proper functioning and prevent
overheating of the Product, do not cover or block the ventilation holes of the
Product. · Follow the installation instructions with the installation tools
provided or recommended. · The use or placement of the operation tools shall
comply with the code of practice of such tools to avoid short circuit of the
Product. · Cut off the power before inspection of the Product to avoid human
injury or product damage.
VT-MITX-TGL | User Manual
3
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
Precautions for Power Cables and Accessories
Use proper power source only. Make sure the supply voltage falls within the
specified range.
Place the cables properly at places without extrusion hazards.
There is a coin cell battery for powering the RTC. Therefore, please avoid
short circuit of the battery during transportation or operation at high
temperatures.
Cleaning instructions:
· Power off before cleaning the Product · Do not use spray detergent · Clean
with a damp cloth · Do not try to clean exposed electronic components unless
with a dust collector
Power off and contact Vantron technical support engineer in case of the
following faults:
· The Product is damaged · The temperature is excessively high · Fault is
still not solved after troubleshooting according to this manual
Do not use in combustible and explosive environment:
· Keep away from combustible and explosive environment · Keep away from all
energized circuits · Unauthorized removal of the enclosure from the device is
not allowed · Do not change components unless the power cable is unplugged. ·
In some cases, the device may still have residual voltage even if the power
cable is
unplugged. Therefore, it is a must to remove and fully discharge the device
before replacement of the components.
VT-MITX-TGL | User Manual
4
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
CHAPTER 1 INTRODUCTION
VT-MITX-TGL | User Manual
5
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
1.1 Product Overview
The VT-MITX-TGL single board computer adheres to the international industry
size standards with a 170mm x 170mm form factor. It is powered by the latest
11th Gen Intel® CoreTM U series processor that combines best-in-class
technologies to offer the best user experience. It supports high-definition
audio encoding and decoding to provide outstanding clarity and fidelity.
Better yet, it provides rich interfaces and customer expansion options to meet
varying application scenarios including smart retail, self-service terminals,
industrial automation, intelligent medical health, and digital media.
Featuring high flexibility and high performance, the motherboard could work
under extreme environments with extended temperatures ranging from -40 to +85,
making it a reliable solution for industrial applications.
1.2 Terminology/Acronym
Terminology/Acronym
NC
VCC GND
P (+)
N (-) # I O I/O P A OD
PCIe MDI BKL
Description
No connection
Voltage common collector Ground
Positive of difference signal Negative of difference signal
Active low signal Input Output
Input/output Power or ground
Analog Open drain PCI express signal Media dependent interface Backlight
VT-MITX-TGL | User Manual
6
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
1.3 Block Diagram
LTE Aux/GNSS
LTE Main
Type 3042 / 3052 M.2 Key B
1x SIM Card Holder
WIFI Type 2230 M.2 Key E
10/100/1000M RJ45
10/100/1000M RJ45
SATA3.0 Direct
SATA3.0 pwoer
2x USB 3.0 TYPE A
2x USB2.0 TYPE A
1x USB 3.0 TYPE C
2×2 USB2.0 Connector 1xUSB2.0 Connector
Speaker header+Headset
Speaker Connector
Connector
TPA3113D2
Thermal
Discrete VR
X1 PCIe+USB3.1
Interface
Chip
DDR
2×260 Sodimm DDR4
Support 64GB max
x1 PCIe+USB2.0+CNV
LAN7430 LAN7430
X1 PCIe Gen 3 X1 PCIe Gen 3
SATA0
USB3.0 USB2.0 TCP2 USB2.0
Tiger Lake UP3 i3-1115G4 TDP 28W FCBGA1449
Audio Codec (ES8336)
HDA/SWD
WDT
eSPI
Embedded Contrller Microchip MEC
1428
GPIO
SPI
PORT80 2X3 2MM
USB2.0
DDIA DDIB GPIO_PWM TCP1
TCP0
PPTNN3344606B0SBS
eDP LVDS LVDS POWER HDMI DP
X4 PCIe Gen 4&SATA1 SPI
SPI
Type 2242/2280 M.2 Key M
TPM 2.0 ATTPM20P
BIOS
GPIO
I2C GPIO
2x Wafer for Smart Fan
1I2C/debug
16GPIO Connector 2×5,2x2mm
FRONT PANEL HEADER 2×4,2.54mm
Buzzer
2xRS232, 2xRS232/ RS422/RS485
XR21V1414 TQFP48
RTC
System Power
DC/DC SY8308RBC Converter
DC JACK
12-36VDC(MAX ~90W)
VT-MITX-TGL | User Manual
7
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
1.4 Specifications
System Communication
CPU
Memory Storage Ethernet Graphics
Media
Display
Audio CODEC
Audio interface
Serial
USB
I/Os
GPIO
I2C
SIM card holder
Expansion M.2
Firmware
System Control Mechanical Power Software
BIOS H/W monitor RTC Watchdog Security (optional) FP header Dimensions Heat dissipation Input Operating system OTA tool
Environment Temperature Condition Certification
VT-MITX-TGL
11th Gen Intel® CoreTM U-Series i3-1115G4/ i5-1155G7/ i7-1195G7
processor
2 x DDR4 SO-DIMM socket, 3200MHz, up to 64GB
1 x SATA 3.0 (Expandable via M.2 M-Key)
2 x RJ45, Realtek® 1Gbps PCIe Ethernet controller
Intel® Iris® Xe Graphics
1 x HDMI: Resolution up to 4096 x 2160 @24Hz
1 x DP: Resolution up to 4096 x 2160 @24Hz
1 x eDP: Resolution up to 4096 x 2160 @60Hz
1 x LVDS/eDP: LVDS, resolution up to 1920 x 1200 @60Hz;
eDP, resolution up to 4096 x 2160 @60Hz
Realtek® 5.1 channel HDA Codec
1 x Mic/Line-out
1 x Headphone jack
2 x Speaker connector
1 x Microphone jack
2 x RS232
2 x RS232/RS422/RS485
2 x USB 2.0 Type-A
1 x USB 3.1 Type-C
2 x USB 3.0 Type-A
3 x Built-in USB 2.0
16 x GPIO
1 x I2C
1 x Nano SIM card holder (connected to M.2 B-Key)
1 x M.2 B-Key (3042/3052, PCIe x 1 / USB 3.1 for 4G/5G expansion)
1 x M.2 M-Key (2242/2280, PCIe x 4 / SATA for SSD expansion)
1 x M.2 E-Key (2230, PCIe x 1 / USB 2.0/CNVi for Wi-Fi expansion)
BYOSOFT (Optional: AMI, Insyde, Phoenix)
Voltages & temperatures
Processor integrated RTC
Programmable WDT to generate system reset events
TPM 2.0 supported (Infineon SLB 9670)
1 x Front panel header (power button, reset button, LED power)
170mm x 170mm
1 x System fan
1 x CPU fan connector
12V DC (1 x 4-pin power header, 1 x Power jack)
Windows 10, Linux
BlueSphere OTA
Operating: 0~+60 (Optional: -40~+85)
Storage: -20~+75 (Optional: -55~+85)
CCC, UL, FCC (Part 15 class B), ESD (contact: ±8KV and air: ±12KV)
VT-MITX-TGL | User Manual
8
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
1.5 Operating System
VT-MITX-TGL supports Windows 10 and Linux operating systems.
1.6 Mechanical Dimensions
· 170mm x 170mm
1.7 Power Supply and Consumption
VT-MITX-TGL works with +12V DC power input supplied alternatively by a DC
connector or a power jack. The power consumption of the Board is about 70W
with speakers functioning and 60W with speakers not working. It should be
pointed out that the power consumption is largely dependent on the RAM,
storage capacity, and other configurations of the Board.
1.8 Environmental Specifications
VT-MITX-TGL works at a temperature ranging from 0 to +60 (optional: -40~+85),
at relative humidity of 10%~85% for non-condensing purpose, and is designed to
be stored at a temperature ranging from -40 to +85 (optional: -55~+85).
VT-MITX-TGL | User Manual
9
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
CHAPTER 2 CONNECTORS AND PIN ASSIGNMENT
VT-MITX-TGL | User Manual
10
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
2.1 Product Layout
(1) DC in_2 (1) DC in_1
(27)
System
fan
(27) (3) CPU fan con.
eDP
(6) DP
(7) HDMI (20) M.2 M-key (14) USB Type-C (12) 2 x USB 3.0
(13) 2 x USB 2.0
(2) LAN_1 (21) M.2 B-key
(2) LAN_2 (11) F_USB 3
(17) Audio
(25) I2C
(26) 2 x DDR4 SO-DIMM socket
(4) LVDS Nano SIM slot
(5) Backlight (24) GPIO power (23) GPIO_2 (23) GPIO_1
(18) F_Audio (19) SPK_L
(15) SATA 3.0
(16) SATA power
(22) M.2 E-key
(10)
(8) 2 x RS232
(19) SPK_R (11) F_header (9) 2 x
F_USB 2 (11) RS232/422/485
F_USB 1
The board I/Os will be described in detail in 2.3 Connectors and Jumpers following the sequencing numbers provided here.
2.2 System Configurations
2.2.1 CPU
VT-MITX-TGL is powered by the latest 11th Gen Intel® CoreTM U series processor
that boasts many best-in-class features.
2.2.2 Memory
VT-MITX-TGL is equipped with two DDR4 SO-DIMM sockets that support up to 64GB
RAM in total with transfer rate at 3200MHz.
2.2.3 Storage
VT-MITX-TGL offers a SATA 3.0 connector for connection of a storage device.
The storage capacity is also expandable via an M.2 B-Key slot that supports
64GB by default.
VT-MITX-TGL | User Manual
11
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
2.3 Connectors and jumpers
This section is going to brief on the connectors/jumpers with corresponsive
pinout description. Unless otherwise stated, pin 1 of a connector is seated on
a square pad that is different from the round pads used for other pins.
Sometimes, pin 1 is next to a trigonal mark on the board. When there are two
rows of pins on a connector, the row with pin 1 is composed of odd numbers and
the other is composed of even numbers.
Usually, there will be numbers or marks next to the pins of a connector on the
board to indicate the pinouts.
2.3.1 J8/J4 Power input (1)
VT-MITX-TGL provides a 4-pin power connector (J4) and a power jack (J8) to
supply power for the Board. Specification of the power connector: 2 x 2 x
4.2mm, 12.8mm (H), Male, Vertical, White, WDT, THR, RoHS Specification of the
power jack: 2.5mm (D), 5.5mm (D), 10A, Male, RA, WDT, THR, RoHS
Pin 3
Pin 1
Pinout description of the 4-pin power connector:
Pin
Signal
1
GND
2
GND
3
+VDC
4
+VDC
Description Ground Ground
DC-IN POWER + DC-IN POWER +
VT-MITX-TGL | User Manual
12
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
Pinout description of the power jack:
Pin
Signal
1
+VDC
2
GND
Description DC-IN POWER +
Ground
2.3.2 J20/J23 Ethernet ports (2)
VT-MITX-TGL offers two RJ45 Ethernet jacks each with two LEDs (L-Y, R-G),
green for activity indication and yellow for link indication.
Specification: Standard RJ45 10M/100M/1000M Base-T Ethernet jack.
Pinout description:
Pin
Signal
1
L_MDI_0P
2
L_MDI_0N
3
L_MDI_1P
4
L_MDI_1N
5
L_MDI_2P
6
L_MDI_2N
7
L_MDI_3P
8
L_MDI_3N
Description Ethernet MDI0+ Signal Ethernet MDI0- Signal Ethernet MDI1+ Signal Ethernet MDI1- Signal Ethernet MDI2+ Signal Ethernet MDI2- Signal Ethernet MDI3+ Signal Ethernet MDI3- Signal
2.3.3 J7 eDP connector (3)
VT-MITX-TGL offers an eDP connector for connection of a display. Specification: 1 x 30 x 0.5mm, 0.5A, 1.05mm (H), Right Angle, WDT, SMT, RoHS
Pin 1
Pinout description:
Pin
Signal
1
+V3.3DX_EDP1
2
+V3.3DX_EDP1
3
+V3.3DX_EDP1
4
eDP_HPD_CONN
VT-MITX-TGL | User Manual
13
Description LCD POWER +3.3V LCD POWER +3.3V LCD POWER +3.3V
LVSAE_DATA
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
5
GND
6
DDIA_EDP1_LANE0_L_DN
7
DDIA_EDP1_LANE0_L_DP
8
GND
9
DDIA_EDP1_LANE1_L_DN
10
DDIA_EDP1_LANE1_L_DP
11
GND
12
DDIA_EDP1_LANE2_L_DN
13
DDIA_EDP1_LANE2_L_DP
14
GND
15
DDIA_EDP1_LANE3_L_DN
16
DDIA_EDP1_LANE3_L_DP
17
GND
18
DDIA_EDP1_AUX_DN
19
DDIA_EDP1_AUX_DP
20
GND
21
GND
22
EDP1_BKLT_EN_R
23
EDP1_BRIGHTNESS_R
24
GND
25
GND
26
GND
27
+VCC_EDP1_BKLT_R
28
+VCC_EDP1_BKLT_R
29
+VCC_EDP1_BKLT_R
30
+VCC_EDP1_BKLT_R
Ground LVSAE_DATA LVSAE_DATA
Ground LVSAE_DATA LVSAE_DATA
Ground LVSDO_DATA LVSDO_DATA
Ground LVSDO_DATA LVSDO_DATA
Ground LVSAE_CLOCK LVSAE_CLOCK
Ground Ground BKLT_EN BRIGHTNESS Ground Ground Ground LCD POWER +12V LCD POWER
+12V LCD POWER +12V LCD POWER +12V
VT-MITX-TGL | User Manual
14
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
2.3.4 J19 LVDS/eDP connector (4)
VT-MITX-TGL also offers an LVDS/eDP connector for connection of a display.
Specification: 2 x 15, 2.0mm, 1.5A, 6mm (H), Male, Vertical, WDT, SMT, RoHS
Pin 1 Pin 2
Pinout description:
Pin
Signal
1
VDD_LCD
2
VDD_LCD
3
VDD_LCD
4
NC
5
LCD_DETECT_R
6
SEL 6/8
7
LVDS_A_D0-_R
8
LVDS_A_D0+_R
9
LVDS_A_D1-_R
10
LVDS_A_D1+_R
11
LVDS_A_D2-_R
12
LVDS_A_D2+_R
13
GND
14
GND
15
LVDS_A_CLK-_R
16
LVDS_A_CLK+_R
17
LVDS_A_D3-_R
18
LVDS_A_D3+_R
19
LVDS_B_D0-/TX0-
20
LVDS_B_D0+/TX0+
21
LVDS_B_D1-/TX1-
22
LVDS_B_D1+/TX1+
23
LVDS_B_D2-/TX2-
Description LCD POWER +5V LCD POWER +5V LCD POWER +5V
LVDS DETECT SELECT 6 OR 8 DEPTH
LVSDO_DATA LVSDO_DATA LVSDO_DATA LVSDO_DATA LVSDO_DATA LVSDO_DATA
Ground Ground LVSDO_CLOCK LVSDO_CLOCK LVSDO_DATA LVSDO_DATA LVSAE_DATA
LVSAE_DATA LVSAE_DATA LVSAE_DATA LVSAE_DATA
VT-MITX-TGL | User Manual
15
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
24
LVDS_B_D2+/TX2+
25
GND
26
GND
27
LVDS_B_CLK-/AUX-
28
LVDS_B_CLK+/AUX+
29
LVDS_B_D3-/TX3-
30
LVDS_B_D3+/TX3+
LVSAE_DATA Ground Ground
LVSAE_CLOCK LVSAE_CLOCK LVSAE_DATA LVSAE_DATA
2.3.5 J27 Backlight connector (5)
VT-MITX-TGL offers a backlight connector that supplies power for the backlight
of the display connected to the LVDS/eDP connector. Specification: 1 x 6 x
2.0mm, 2A, 6mm (H), Male, Vertical, WDT, THR, RoHS
Pin 1
Pinout description:
Pin
Signal
1
VCC_BLK
2
VCC_BLK
3
LCD_BKLTEN
4
LCD_BKLT_PWM
5
GND
6
GND
Description LCD BACKLIGHT POWER +12V LCD BACKLIGHT POWER +12V
LCD BACKLIGHT ENABLE LCD BACKLIGHT PWM
Ground Ground
VT-MITX-TGL | User Manual
16
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
2.3.6 J10 DP (6)
VT-MITX-TGL implements a DP 1.4 interface that supports resolution of 4096 x
2160 @24Hz. Specification: Type-A, No FLN, Female, Right Angle, WDT, SMT, RoHS
Pinout description:
Pin
Signal
1
DDI4_DP_TX0_L_DP
2
GND
3
DDI4_DP_TX0_L_DN
4
DDI4_DP_TX1_L_DP
5
GND
6
DDI4_DP_TX1_L_DN
7
DDI4_DP_TX2_L_DP
8
GND
9
DDI4_DP_TX2_L_DN
10
DDI4_DP_TX3_L_DP
11
GND
12
DDI4_DP_TX3_L_DN
13
DDI4_OB_AUX_EN
14
DDI4_DPCON_PIN14_PD
15
DDI4_DP_CTRLCLK_AUX_DP
16
DDI4_DP_CTRLDATA_AUX_DN
17
GND
18
DDI4_OB_DP_HPD
19
GND
20
+V3.3S_DDI4_OB_DP_Q
Description DP DATA Ground DP DATA DP DATA Ground DP DATA DP DATA Ground DP
DATA DP DATA Ground DP DATA AUX_EN
HDMI DATA DP DDI CLK DP DDI DATA
Ground DP HOT PLUG DETECTION
Ground DP POWER +3.3V
VT-MITX-TGL | User Manual
17
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
2.3.7 J11 HDMI (7)
VT-MITX-TGL implements an HDMI 2.0b interface that supports resolution of 4096
x 2160 @60Hz. Specification: Type-A, FLN, Female, Right Angle, WDT, SMT, RoHS
Pinout description:
Pin
Signal
1
HDMI_DATA2+
2
GND
3
HDMI_DATA2-
4
HDMI_DATA1+
5
GND
6
HDMI_DATA1-
7
HDMI_DATA0+
8
GND
9
HDMI_DATA0-
10
HDMI_CLK+
11
GND
12
HDMI_CLK-
13
NC
14
NC
15
HDMI_DDC_SCL
16
HDMI_DDC_SDA
17
GND
18
VCC_HDMI
19
HDMI_HPD
Description HDMI DATA
Ground HDMI DATA HDMI DATA
Ground HDMI DATA HDMI DATA
Ground HDMI DATA HDMI CLK
Ground HDMI CLK
HDMI DDC I2C CLK HDMI DDC I2C DATA
Ground HDMI POWER +5V HDMI HOT PLUG DETECTION
VT-MITX-TGL | User Manual
18
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
2.3.8 J52/J53 RS232 (8)
VT-MITX-TGL implements two RS232 connectors (COM3 & COM4). Specification: 2 x
5 x 1.50mm, 5.75mm (H), Male, Vertical, Black, WDT, THR, RoHS
Pin 2
Pin 1 Pinout description of J52 (COM3):
Pin
Signal
1
DCD3_L
2
RXD3_L
3
TXD3_L
4
DTR3
5
GND
6
DSR3
7
RTS3
8
CTS3
9
RI3_L
Pinout description of J53 (COM4):
Pin
Signal
1
DCD4_L
2
RXD4_L
3
TXD4_L
4
DTR4
5
GND
6
DSR4
7
RTS4
8
CTS4
9
RI4_L
Description POWER
RS232_RXD RS232_TXD
DTR3 Ground DSR3
RTS3 CTS3 RI3_L
Description POWER
RS232_RXD RS232_TXD
DTR4 Ground DSR4
RTS4 CTS4 RI4_L
VT-MITX-TGL | User Manual
19
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
2.3.9 J50/J51 RS232/RS422/RS485 (9)
VT-MITX-TGL implements another two RS232/RS422/RS485 connectors (COM1 & COM2)
next to the two RS232 connectors. Specification: 2 x 5 x 1.50mm, 5.75mm (H),
Male, Vertical, Black, WDT, THR, RoHS Pin 2
Pin 1
Pinout description of J50 (COM1):
Pin RS232
Signal RS485
1
DCD1
RS485_A
2
RXD1
RS485_B
3
TXD1
/
4
DTR1
/
5
GND
/
6
DSR1
/
7
RTS1
/
8
CTS1
/
9
RI1_L
/
Pinout description of J51 (COM2):
Pin RS232
Signal RS485
1
DCD2
RS485_A
2
RXD2
RS485_B
3
TXD2
/
4
DTR2
/
5
GND
/
6
DSR2
/
7
RTS2
/
8
CTS2
/
9
RI2_L
/
RS422 RS422TX+ RS422TXRS422RX+ RS422RX-
/ / / / /
RS422 RS422TX+ RS422TXRS422RX+ RS422RX-
/ / / / /
VT-MITX-TGL | User Manual
20
Description
DATA DATA DATA DATA GND DATA DATA DATA DATA
Description
DATA DATA DATA DATA GND DATA DATA DATA DATA
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
2.3.10 J49 Front panel connector (10)
The front panel connector provides signals for system power/reset and LED
power. Specification: 2 x 4, 2.54mm, 2A, 6mm (H), Male, Vertical, WDT, THR,
RoHS Pin 2
Pin 1
Pinout description:
Pin
Signal
1
SATA_ACT+
2
LED_POWER
3
SATA_ACT#
4
GND
5
GND
6
PBTN_IN#
7
SYS_REST#
8
GND
Description SATA_ACT+ LED POWER SATA_ACT+
GND GND Power Button SYS_REST GND
VT-MITX-TGL | User Manual
21
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
2.3.11 J32/J37/J38 USB 2.0 connectors (11)
VT-MITX-TGL offers three USB 2.0 connectors, one is a 4-pin connector (J32),
the other two are 10-pin connectors (J37 & J38). Specification of J32: 1 x 4 x
2.0mm, 2A, 6mm(H), Male, RA, WDT, THR, RoHS Specification of J37/J38: 2 x 5 x
2.54mm, 2A, 6mm (H), Male, Vertical, WDT, THR, RoHS
J32 Pin 2
J37/J38
Pin 1
Pinout description of J32:
Pin
Signal
1
VCC_USB2.0_1
2
USB2.0_DN
3
USB2.0_DP
4
GND
Pin 1
Description USB POWER +5V Reserved usb2.0 Negative Reserved usb2.0 Positive
Ground
Pinout description of J37/J38:
Pin
Signal
1
VCC_USB2.0_2
2
VCC_USB2.0_2
3
USBHUB_3N
4
USBHUB_2N
5
USBHUB_3P
6
USBHUB_2P
7
GND
8
GND
10
NC
Description USB POWER +5V USB POWER +5V Reserved usb2.0 Negative Reserved
usb2.0 Positive Reserved usb2.0 Negative Reserved usb2.0 Positive
Ground Ground
VT-MITX-TGL | User Manual
22
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
2.3.12 J16 USB 3.0 Type-A (12)
There are two USB 3.0 Type-A interfaces on the Board for expansion of
functions. Specification: 3.0, Type-A, Female, 17.5mm (L), Right Angle, WDT,
THR, RoHS The pinout description of the interfaces is in line with the pin
assignment of standard USB 3.0 Type-A.
USB 3.0 USB 3.0
2.3.13 J18 USB 2.0 Type-A (13)
There are another two USB 2.0 Type-A interfaces on the Board designed to
connect peripherals to expand the functions. Specification: 2.0, Type-A,
Female, Right Angle, Retention, WDT, THR, RoHS The pinout description of the
interfaces is in line with the pin assignment of standard USB 2.0 Type-A.
USB 2.0 USB 2.0
2.3.14 J15 USB 3.1 Type-C (14)
VT-MITX-TGL implements a USB 3.1 Type-C interface that supports OTG
functionality to allow greater flexibility for device communication.
Specification: 3.1, Type C, Female, 17.5mm (L), Right Angle, WDT, THR, RoHS
USB 3.1
The pinout description of the interface is in line with the pin assignment of
standard USB 3.1 Type-C.
VT-MITX-TGL | User Manual
23
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
2.3.15 J54 SATA connector (15)
The SATA connector is designed to connect a storage device for capacity
expansion. Specification: 7-Pin, 1.27mm, 8.4mm (H), WDT, SMT, RoHS The pinout
description of the connector is in line with the pin assignment of standard
SATA connector.
2.3.16 J48 SATA power connector (16)
VT-MITX-TGL offers a 4-pin power connector to supply power to the storage
device. Specification: 1 x 4 x 2.54mm, 2A, 6mm (H), Male, Vertical, WDT, THR,
RoHS
Pin 1
Pinout description:
Pin 1 2 3 4
Signal +V5_S GND GND +V12_S
Description POWER +5V
Ground Ground POWER +12V
2.3.17 J56 Audio jacks (17)
VT-MITX-TGL offers two 3.5mm audio jacks on the Board, one is a headphone jack
and the other is a Microphone jack.
Specification: 3.6mm, 4-Pole + 1 Switch, Female, Right Angle, THR, RoHS
Headphone Microphone
VT-MITX-TGL | User Manual
24
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
Pinout description:
Pin 1 2 3 4 5 21 22 23 24 25
Signal GND HPOUT_L_CRL HP_JD GND HPOUT_R_CRL GND MIC1_LLL MIC_JD GND MIC1_RRR
Description Ground
AUDIO JACK LEFT VOICE HP Insert Ground
AUDIO JACK RIGHT VOICE Ground
LEFT INPUT MIC Insert
Ground RIGHT INPUT
2.3.18 J25 F_AUDIO connector (18)
There is a front panel audio connector on the Board which allows you to
connect an audio jack to the front panel. Specification: 2 x 5 x 2.54mm, 3A,
6mm (H), Male, Vertical, THR, RoHS
Pin 2
Pin 1
Pinout description:
Pin 1 2 3 4 5 6 7 9 10
Signal MIC2_LLL
GND MIC2_RRR
NC RINP_AMP2
MIC2_JD GND
LINP_AMP2 HP2_JD
Description MIC LEFT INPUT
Ground MIC RIGHT INPUT
AMP2 RIGHT INPUT MIC2 JD INPUT Ground
AMP2 LEFT INPUT HP2 JD INPUT
VT-MITX-TGL | User Manual
25
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
2.3.19 J46/J47 Speaker connectors (19)
There are two speaker connectors on the Board, providing left and right stereo
sound experience to users when connected to the speakers. Specification of the
connectors: 1 x 2 x 2.54 mm, 4A, 10.8mm (H), Male, Vertical, THR, RoHS
Pin 1 Pin 1
J46 Speaker (L)
J47 Speaker (R)
Pinout description of the J46 connector:
Pin
Signal
1
OUTPL+
2
OUTPL-
Pinout description of the J47 connector:
Pin
Signal
1
OUTPR+
2
OUTPR-
Description 8R/5W SPEAKER ANODE 8R/5W SPEAKER CATHODE
Description 8R/5W SPEAKER ANODE 8R/5W SPEAKER CATHODE
2.3.20 J14 M.2 M-Key (20)
VT-MITX-TGL offers an M.2 M-Key socket (2242/2280) that supports PCIe x 4 /
SATA bus interface to connect an SSD for high-speed data transfer and storage.
The pinout of the socket is in line with the pin assignment of standard M.2
for Key M.
2.3.21 J24 M.2 B-Key (21)
VT-MITX-TGL offers an M.2 B-Key socket (3042/3052) that supports PCIe x 1 /
USB 3.1 bus interface to connect a 4G/5G module for wireless communication.
The pinout of the socket is in line with the pin assignment of standard M.2
for Key B.
2.3.22 J21 M.2 E-Key (22)
VT-MITX-TGL offers an M.2 E-Key socket (2230) that supports PCIe x 1 / USB 2.0
/ CNVi bus interface to connect a Wi-Fi & Bluetooth module for wireless
communication. The pinout of the socket is in line with the pin assignment of
standard M.2 for Key E.
VT-MITX-TGL | User Manual
26
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
2.3.23 J31/J34 GPIO (23)
There are two GPIO connectors on the Board, offering 16 GPIO signals. Specification: 2 x 5 x 2.0mm, 1.5A, 5.5mm (H), Male, Vertical, WDT, THR, RoHS
Pin 1 Pin 2
Pinout description of J31:
Pin
Signal
1
GPIO_0_3.3V
2
GPIO_1_3.3V
3
GPIO_2_3.3V
4
GPIO_3_3.3V
5
GPIO_4_3.3V
6
GPIO_5_3.3V
7
GPIO_6_3.3V
8
GPIO_7_3.3V
9
GND
10
GPIO POWER
Description GPP_U4 GPP_U5 GPP_U2 GPP_H4 GPP_D0 GPP_D1 GPP_D2 GPP_D3 Ground
GPIO POWER
Pinout description of J34:
Pin
Signal
1
GPIO_8_3.3V
2
GPIO_9_3.3V
3
GPIO_10_3.3V
4
GPIO_11_3.3V
5
GPIO_12_3.3V
6
GPIO_13_3.3V
7
GPIO_14_3.3V
8
GPIO_15_3.3V
9
GND
10
GPIO POWER
Description GPP_S1 GPP_S0 GPP_S3 GPP_S2 GPP_R0 GPP_R1 GPP_R2 GPP_R3 Ground
GPIO POWER
VT-MITX-TGL | User Manual
27
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
2.3.24 J29 GPIO power (24)
There is a GPIO power connector on the Board for connecting a power source to
supply power to the GPIO. Specifications: 1 x 3, 2.0mm, 1.5A, 6mm (H), Male,
Vertical, WDT, THR, RoHS
Pin 1
Pinout description: Pin 1 2 3
Signal +V5S VCC_GPIO +V3.3S
Description +V5 POWER
GPIO +V3.3 POWER
2.3.25 J9 I2C (25)
The Board offers a three-pin I2C connector. Specification: 1 x 3 x 1.25mm, 1A,
4.6mm (H), Male, Vertical, THR, RoHS
Pin 1
Pinout description:
Pin
Signal
1
GND
2
I2C5_SDA_PWRMTR
3
I2C5_SCL_PWRMTR
Description Ground I2C5 SDA I2C5 SCL
VT-MITX-TGL | User Manual
28
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
2.3.26 J12/J13 DDR4 SO-DIMM Sockets (26)
The two DDR4 SO-DIMM sockets on the Board support up to 64GB RAM in total with transfer rate at 3200MHz.
2.3.27 J5/J6 Fan Connectors (27)
VT-MITX-TGL implements two fan connectors, one (J6) is connected to a fan that
offers active heat dissipation for the system, and the other (J5) is a CPU fan
connector for user to customize.
Specification: 1 x 4 x 2.54mm, 4A, 11.4mm (H), Male, Vertical, THR, RoHS
Pinout description of J5:
Pin
Signal
1
GND
2
FAN SUPPLY_+V12
3
CPU_TACHO_R_FAN
4
FAN_CONN_PWM_IN
Description Ground
+12V POWER FAN SPEED FEEDBACK FAN SPEED CONTROL
Pinout description of J6:
Pin
Signal
1
GND
2
FAN SUPPLY_+V12
3
NA
4
NA
Description Ground
+12V POWER
VT-MITX-TGL | User Manual
29
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
CHAPTER 3 FIRST-USE DEBUGGING
VT-MITX-TGL | User Manual
30
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
3.1 Driver Introduction
The table below lists the drivers in the software release package of the Board (path: 700RBX730K302_VT-mITX-TGL_Win11_22H2_en_x64_vxx_xxx-xxx-xxx3 Sw-Driver) that might be used to run VT-MITX-TGL and their respective use.
Driver
Description
Audio
Codec and SST drivers for running the audio devices
Chipset
To tell the user if the chipset INF file needs to be updated
Graphic
Intel graphics driver
LAN
Microchip LAN7400 device driver
Serial IO
Intel serial IO driver
TXE
To manage the Intel CSME firmware
USB2COM
USB to UART driver
VT-MITX-TGL | User Manual
31
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
3.2 Serial Port Setup
VT-MITX-TGL implements 4 high-speed serial connectors (COM1 ~ COM4). COM1 and
COM2 are mapped as serial port 1 and serial port 2 respectively in the BIOS
system. COM1 and COM2 support RS232, RS485, RS422 protocols, while COM3 and
COM4 support RS232 protocol. If you wish to change the mode of COM1 and COM2,
- Press F2 during the system boot to enter BIOS; 2. Navigate to Advanced >
Intel Advanced Menu > Vantron Configuration; 3. Move the cursor to Serial Port
1 Mode / Serial Port 2 Mode
, and press Enter; 4. Use the up & down arrows to change the mode;
5. Press F10 to save and exit.
Then You can run the TestCommPC Vxxx program in the release package (4 SWTestsUART) for serial debugging.
VT-MITX-TGL | User Manual
32
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
3.3 GPIO Setup
VT-MITX-TGL implements 16 GPIOs with details shown below:
Pin J57.1 J57.2 J57.3 J57.4 J57.5 J57. 6 J57.7 J57.8 J59.1 J59.2 J59.3 J59.4 J59.5 J59. 6 J59.7 J59.8
Name GPIO_0 GPIO_1 GPIO_2 GPIO_3 GPIO_4 GPIO_5 GPIO_6 GPIO_7 GPIO_8 GPIO_9 GPIO_10 GPIO_11 GPIO_12 GPIO_13 GPIO_14 GPIO_15
Default mode Output Output Output Output Output Output Output Output Output Output Output Output Output Output Output Output
Default level High High High High High High High High High High High High High High High High
You can use the Test_Tgl_OnboardGPIO program (4 SW-TestsGPIO) in the release package for GPIO debugging.
VT-MITX-TGL | User Manual
33
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
In the above figure:
1. GpioPins: You can select a pin of the GPIO header from the drop-down list
for the configuration;
2. Out: Set the mode of the selected GPIO pin as output (checked)/input
(unchecked);
3. High: Set the level of the selected GPIO pin as high (checked)/low
(unchecked).
Please run this program as administrator.
VT-MITX-TGL | User Manual
34
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
CHAPTER 4 BIOS AND WINDOWS
VT-MITX-TGL | User Manual
35
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
4.1 BIOS Introduction
BIOS initializes hardware like CPU and memory, and saves hardware settings for
installation and loading of the operating system (OS). Users may need to run
BIOS Setup program when: · An error message appears suggesting that the user
should run BIOS Setup; · Default settings need to be customized.
Please be aware that BIOS will be under continuous update for better system
performance, therefore the description in this chapter might vary slightly and
is for reference only.
4.2 BIOS Setup
4.2.1 Entering BIOS Setup Utility
When the Board is powered on, the system will start the power-on self-test
process. Then you can press F2 to enter the BIOS configuration page for more
settings.
The menu bar comprises:
· Platform Information Menu: Basic system configurations, like BIOS
information, FSP information, Board information, processor information,
firmware information, system time and date, etc.
· Advanced: Advanced configurations that allow users to customize the system
and board settings
· Security: System security settings where users can set the administrator and
user passwords, manage the passwords, etc.
· Boot: System boot options
· Exit: BIOS load or exit options with or without changes saved
VT-MITX-TGL | User Manual
36
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
4.2.2 Selecting a Boot Option
After powering on the Board, you can press F7 to enter the boot manager menu.
Windows Boot Manager is used to access the Windows operating system installed
on the Board. When selected, it initiates the boot process for Windows.
Internal UEFI Shell is a command line interface that provides access to a
range of commands and utilities to be used for network booting, system
management or recovery, system diagnostics, troubleshooting, etc. UEFI SanDisk
xxxx is a specific boot entry associated with the SanDisk device. This option
allows you to boot the Board from this bootable device. Please refer to 4.3.2
Making a Bootable USB Drive for Window 10 for the details of making a bootable
USB device.
VT-MITX-TGL | User Manual
37
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
4.3 Windows 10 System Upgrade
4.3.1 Prerequisites
· A USB drive with capacity no less than 8GB, preferably supporting USB 3.0 ·
Program for making the bootable device: rufus-xxx .exe (available in the
release
package under 5 image) · Windows 10 image (available in the release package
under 5 image) · A host computer running Windows system · An HDMI cable to
connect the Board and the host PC · A USB mouse and keyboard
4.3.2 Making a Bootable USB Drive for Windows 10
Plug the USB drive into the host PC. Run rufus-xxx .exe and it will
automatically detect the USB drive. Then follow the steps below to make a
bootable USB drive. 1. Click on Device and choose the USB you want to use from
the drop-down; 2. Select the ISO image you want to burn onto the USB from the
drop-down and click
Select; 3. Generally, users would like to create a Standard Windows
installation, and Rufus will
automatically detect the correct Partition Scheme based on the USB drive. Yet
make sure the partition scheme is GPT; 4. Set the Target system as UEFI and
the File system as FAT32 or NTFS; 5. Click START to make the bootable USB
drive.
VT-MITX-TGL | User Manual
38
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions 6. Unplug the
USB drive from the host computer after the bootable device is successfully
made.
4.3.3 Installing Windows 10
1. Plug the bootable USB drive into the Board; 2. Power the Board on and it
will enter the boot process; 3. Press F7 to enter the BIOS boot manager menu;
4. Select the bootable USB drive you created for Windows 10 and press ENTER;
5. Wait for the installation of Windows 10 on the Board.
VT-MITX-TGL | User Manual
39
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
CHAPTER 5 DISPOSAL AND WARRANTY
VT-MITX-TGL | User Manual
40
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
5.1 Disposal
When the device comes to end of life, you are suggested to properly dispose of
the device for the sake of the environment and safety.
Before you dispose of the device, please back up your data and erase it from
the device.
It is recommended that the device is disassembled prior to disposal in
conformity with local regulations. Please ensure that the abandoned batteries
are disposed of according to local regulations on waste disposal. Do not throw
batteries into fire or put in common waste canister as they are explosive.
Products or product packages labeled with the sign of “explosive” should not
be disposed of like household waste but delivered to specialized electrical &
electronic waste recycling/disposal center.
Proper disposal of this sort of waste helps avoid harm and adverse effect upon
surroundings and people’s health. Please contact local organizations or
recycling/disposal center for more recycling/disposal methods of related
products.
VT-MITX-TGL | User Manual
41
www.vantrontech.com
Vantron | Embedded in your success, Embedded in your better life
World-leading provider of embedded/IoT products and solutions
5.2 Warranty
Product warranty
VANTRON warrants to its CUSTOMER that the Product manufactured by VANTRON, or
its subcontractors will conform strictly to the mutually agreed specifications
and be free from defects in workmanship and materials (except that which is
furnished by the CUSTOMER) upon shipment from VANTRON. VANTRON’s obligation
under this warranty is limited to replacing or repairing at its option of the
Product which shall, within 24 months after shipment, effective from invoice
date, be returned to VANTRON’s factory with transportation fee paid by the
CUSTOMER and which shall, after examination, be disclosed to VANTRON’s
reasonable satisfaction to be thus defective. VANTRON shall bear the
transportation fee for the shipment of the Product to the CUSTOMER.
Out-of-Warranty Repair
VANTRON will furnish the repair services for the Product which are out-of-
warranty at VANTRON’s then-prevailing rates for such services. At customer’s
request, VANTRON will provide components to the CUSTOMER for non-warranty
repair. VANTRON will provide this service as long as the components are
available in the market; and the CUSTOMER is requested to place a purchase
order up front. Parts repaired will have an extended warranty of 3 months.
Returned Products
Any Product found to be defective and covered under warranty pursuant to
Clause above, shall be returned to VANTRON only upon the CUSTOMER’s receipt of
and with reference to a VANTRON supplied Returned Materials Authorization
(RMA) number. VANTRON shall supply an RMA, when required within three (3)
working days of request by the CUSTOMER. VANTRON shall submit a new invoice to
the CUSTOMER upon shipping of the returned products to the CUSTOMER. Prior to
the return of any products by the CUSTOMER due to rejection or warranty
defect, the CUSTOMER shall afford VANTRON the opportunity to inspect such
products at the CUSTOMER’s location and no Product so inspected shall be
returned to VANTRON unless the cause for the rejection or defect is determined
to be the responsibility of VANTRON. VANTRON shall in turn provide the
CUSTOMER turnaround shipment on defective Product within fourteen (14) working
days upon its receipt at VANTRON. If such turnaround cannot be provided by
VANTRON due to causes beyond the control of VANTRON, VANTRON shall document
such instances and notify the CUSTOMER immediately.
VT-MITX-TGL | User Manual
42
www.vantrontech.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>