fender Series 2 Passport Venue Portable PA System Owner’s Manual
- June 13, 2024
- fender
Table of Contents
fender Series 2 Passport Venue Portable PA System Owner’s Manual
PASSPORT® VENUE SERIES 2
Congratulations on purchasing a Fender® Passport Venue Series 2 audio system—a self-contained portable audio system designed for great sound anywhere. Carry Passport like a suitcase, and simply flip open the cabinet-release latches to access two full-range speaker cabinets, a powered mixer, and power and speaker cables.
Use Passport as a public address system or to amplify musical instruments and vocals. Connect mobile devices for easy accompaniment, including Bluetooth audio streaming.
Passport’s quick and easy setup, its ability to cover large audiences and its simple operation are the hallmarks of this innovative product. Its control panel features mono mic/line channels and stereo line channels with a variety of input and output jacks to provide superb flexibility.
Register your Passport Venue Series 2 online at start.fender.com.
SYSTEM SETUP
-
OPEN: Flip open cabinet latches on top of Passport and detach speaker cabinets from powered mixer section:
-
PLACEMENT: For optimal results, elevate speaker cabinets on Passport speaker stands or sturdy tables. Place the speakers far apart to maximize stereo separation. Position mixer close by for easy access to control panel:
-
SPEAKER CABLE/POWER CORD STORAGE: Open storage compartment on rear of mixer and remove power cord and speaker cables:
-
POWER CORD/SPEAKER CABLE CONNECTION : Plug speaker cables into left and right speaker jacks on back of the mixer (upper right arrow), then connect corresponding left and right speakers. Make sure power switch is off before connecting power cord (included) into power inlet on back of mixer (lower left arrow); plug other end into a grounded AC power outlet:
-
INPUTS Connect microphones to channels 1 through 4; connect other mono sound sources such as instruments to any channel. Use channel 7/8 and 9/10 inputs for stereo/mono sound sources such as keyboards, other line-level audio sources, and mobile devices:
-
INITIAL VOLUME/REVERB: Turn MASTER VOLUME knob, all channel VOLUME knobs and all REVERB knobs fully counterclockwise to start
-
POWER UP: Turn on all external equipment connected to Passport first, then turn Passport on. Power LED will illuminate green: SETTING MASTER VOLUME: Turn MASTER VOLUME up to 1/4 volume:
-
SETTING LEVELS: Connect a microphone or other sound source and slowly turn up that channel’s VOLUME control. LED above VOLUME control will illuminate green when signal is present. LED will illuminate yellow when signal is approaching clipping level; will illuminate red when clipping (distortion) occurs. For best performance, set channel VOLUME and TONE controls so that LED is green and occasionally yellow. If LED turns red, reduce VOLUME or TONE control settings. If LED is still turning red after adjusting VOLUME and TONE controls, press MIC/LINE button in
-
SETTING LEVELS: Connect a microphone or other sound source and slowly turn up that channel’s VOLUME control. LED above VOLUME control will illuminate green when signal is present. LED will illuminate yellow when signal is approaching clipping level; will illuminate red when clipping (distortion) occurs. For best performance, set channel VOLUME and TONE controls so that LED is green and occasionally yellow. If LED turns red, reduce VOLUME or TONE control settings. If LED is still turning red after adjusting VOLUME and TONE controls, press MIC/LINE button in
Adjust each channel the same way. Use channel VOLUME knobs to set relative loudness of each channel for overall balance, then adjust MASTER VOLUME knob for overall mix loudness. MASTER VOLUME has a SIGNAL LEVEL METER just to the right; if meter illuminates red, decrease MASTER VOLUME accordingly. -
SETTING TONE/REVERB: Starting with each TONE control (TREBLE, BASS) in the center-détente position (flat equalization), set each TONE control to preference for best clear and consistent sound coverage throughout the area. REVERB controls are not center détente; set these to preference:
FRONT PANEL
A. MASTER VOLUME: Adjusts overall loudness. No sound is produced at full
counterclockwise position.
B. SIGNAL LEVEL METERS: Indicate left/right power amp output signal
level. If meters illuminate red, reduce MASTER VOLUME (A) to prevent
distortion and avoid amp overload/shutdown (see item V, POWER/PROTECT LED, to
reset unit after protect mode shutdown).
C. TONE: Adjusts overall tonal character, with “flat” response at center-
detente position. Rotate clockwise to boost high frequencies and reduce lows;
counterclockwise to reduce highs and boost lows.
D. REVERB SELECT: Press to select one of two reverb types.
“Reverb 1” produces dark hall to bright plate reverb depending on REVERB TONE
(E) setting, with short to long diffusion depending on REVERB TIME (E)
setting. “Reverb 2” produces medium dark to bright hall reverb depending on
REVERB TONE (E) setting, with short to long diffusion depending on REVERB TIME
(E) setting.
E. REVERB TIME/TONE: TIME adjusts reverb “tail” length; TONE adjusts
reverb tonal character.
F. SIGNAL/CLIP LED: Illuminates green when signal is present; yellow when
signal level is -10dB away from clipping. Illuminates red during clipping (see
step 9 under SYSTEM SETUP).
G. CHANNEL VOLUME: Adjusts individual channel loudness.
H. TREBLE/BASS: Adjusts individual channel treble and bass tone, with
“flat” response at center-detented position.
I. REVERB: Adjusts individual channel reverb effect.
J. MIC/LINE SWITCH: For channels 1 through 4 only; if signal source level
is too high (see step 9 under SYSTEM SETUP), press in to reduce input
sensitivity by 24dB.
K. PHANTOM POWER: Press to supply 48V phantom power to channels 1 through
4. NOTE: Use caution when using ribbon microphones, as not all are compatible
with phantom power.
L. MONO CHANNEL INPUT: For channels 1 through 4 only; XLR and 1/4” input
for microphones, instruments and other mono line-level sources.
M. LINE/INSTRUMENT SWITCH: For channels 5 and 6 only, switch activates
high-impedance (“Hi-Z”) preamp for passive instruments such as electric
guitars and basses. For line-level input or if clipping (distortion) occurs,
disengage switch.
N. PAIR BLUETOOTH: For channel 9/10 only; press for Bluetooth pairing
with external devices. When button is flashing blue, select “PASSPORT VENUE”
in external device Bluetooth menu. Button will stop flashing and illuminate
blue continuously when connection is successful. Press and hold button to
disconnect Bluetooth. For best sound quality, set volume control on external
device (i.e., smart phone) to 75-100 percent of its maximum level.
O. 1/4”-ONLY MONO CHANNEL INPUT: For channels 5 and 6 only; 1/4” input
for instruments and other line-level sources.
P. 1/4” LEFT (MONO)/RIGHT INPUT: For channels 7/8 and 9/10 only; inputs
for line-level stereo audio sources requiring separate 1/4” jacks for each
channel. Using stereo L/MONO jack by itself functions as mono channel; mono
output will be heard from both speakers.
Q. 1/8” STEREO INPUT: For channels 7/8 and 9/10 only; input for mobile
devices, computers and other line-level stereo audio sources with 1/8”
connection.
R. HEADPHONE OUTPUT: Connect headphones and recording equipment here.
Individual channel controls affect this output; MASTER VOLUME (A) does not.
S. LEVEL CONTROL: Adjusts HEADPHONE OUTPUT (R) and MONO OUTPUT (T) signal
levels.
T. MONO OUTPUT: For connection to a powered monitor. Signal level is pre-
MASTER VOLUME (A); can be adjusted using LEVEL CONTROL (S).
U. SUB OUTPUT: For connection to a powered subwoofer. Set subwoofer
crossover frequency control to 120Hz. Use subwoofer’s volume or level control
to set bass level to preference. External subwoofer use automatically removes
signals below 120Hz from main Passport amp and speakers.
V. POWER/PROTECT LEDS: POWER LED illuminates green when system is on.
Passport features internal protection measures that will shut down audio
output in the event of electrical or thermal problems; PROTECT LED will
illuminate red when this happens. Passport will automatically reset itself on
resolution of such problems. If Passport does not reset automatically, check
fuse in power cord socket on rear panel (Y). If PROTECT LED remains
illuminated after unit has had sufficient cooling time and other power outlets
have been tried, consult an authorized Fender Service Center.
REAR PANEL
W. VOLTAGE SELECTOR: Change the setting of this 100V/120V– 220V/240V
switch only when using Passport in a country that requires a different voltage
setting.
X. POWER: Turns Passport on and off.
Y. POWER CORD SOCKET/FUSE: Connect power cord (included) to this socket;
plug other end into a grounded AC outlet in accordance with correct VOLTAGE
SELECTOR (W) setting. To check/replace fuse, unplug power cord and pry fuse
holder from POWER CORD SOCKET; replace fuse only with another of the same type
and rating.
Z. SPEAKER OUTPUTS: Connect Passport speaker cables (included) here.
SPECIFICATIONS
TYPE: PR 846
POWER REQUIREMENT: 750W
POWER OUTPUT: 600W
FUSE: T10A H, 250V
AMPLIFIER TYPE: Class D
SPEAKERS: Two 10” woofers, two 1.2” HF drivers
DIMENSIONS AND WEIGHT: Width: 29” (73.6 cm) Height: 23” (58.4 cm) Depth:
11” (27.9 cm) Weight: 44 lbs. (19.96 kg)
Product specifications subject to change without notice.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>