Fly Air 10 8 Inch 2015 Fanatic Inflatable Board User Guide
- June 13, 2024
- FANATIC
Table of Contents
Fly Air 10 8 Inch 2015 Fanatic Inflatable Board
Product Information
Overview:
The Fanatic Fly Air is an inflatable board designed for water activities. This user guide provides step-by-step instructions for setting up and using the Fly Air to ensure maximum enjoyment on the water.
Delivery Status:
Before inflating the board, make sure that the valve on the Fanatic Fly Air is in the outer position. To release the valve, push lightly downwards and twist to the left. The valve should now be in the upper position.
Setup Instructions:
-
Roll out your board on a flat surface. Grass is an ideal surface for setup.
-
Screw the pump hose and pressure gauge onto the pump handle.
The pressure gauge should be on the upper side of the pump, while the air hose should be on the side. -
Connect the air hose to the pump and attach it to the valve of the Fanatic Fly Air with a twist.
-
Ensure your feet are firmly placed on the foot rests of the pump and push directly down over the pump shaft.
-
Pump until you reach a pressure of 10psi, which should take approximately 3 minutes. For higher pressure, continue pumping with a little more effort until you reach 15psi/1 bar. We recommend using a pressure between 15-25psi for optimal performance.
-
Insert the screw into the fin tab, ensuring that the fin box is clean and free of debris. Push the fin flush with the fin box and tighten the fin screw.
Deflation and Storage:
To deflate the Fanatic Fly Air, unscrew the valve cover. Push the valve downwards and twist to the right. Roll up the board starting from the nose, keeping the fins on the outside.
For storage, the Fly Air can be stored inflated. However, prolonged exposure to direct sunlight may cause fading. On hot days, the air inside the board may expand, making it harder. If not using for longer periods, it is recommended to store the Fly Air lightly coiled or ideally unrolled.
SET-UP USER Guide
A guide for all Fanatic Fly Air inflatables. This step by step guide makes sure, that you set up the Fly Air correctly for maximum enjoyment on the water.
-
Roll out your board on a flat surface, grass is ideal.
-
Make sure that the valve on the Fanatic Fly Air is in the outer position. The valve must be released for inflation. To release the valve, push lightly downwards and twist to the left (see picture). The valve is now in the upper position.
- Screw the pump hose and pressure gauge onto the pump handle. The pressure gauge is on the upper side of the pump and the air hose on the side. Connect the air hose with a twist to the pump and on the valve of the Fanatic Fly Air.
-
Make sure your feet are firmly placed on the foot rests of the pump and that you push directly down over the pump shaft.
You will find that you reach 10psi in about 3 minutes and a little more effort will get you to 15psi/ 1 bar.
The harder the board, the better it performs. We recommend using the board at a pres-sure between 15 — 25psi. Don’t worry, it is impossible to over inflate the board using the supplied hand pump. -
Insert the screw into the fin tab. Be sure the fin box is clean and free of debris. Insert the fin into the box opening and push it flush with the fin box. Tighten up the fin screw.
- To deflate the Fanatic Fly Air, unscrew the valve cover. To release the valve, push it down-wards and twist to the right. (see picture). Roll up the board starting from the nose, so the fins are on the outside.
StorAge: The Fly Air can be stored inflated. Direct sunlight over longer periods can cause fading. On hot days, the Fly Air will be harder, as the air expands. When not using for longer periods, store the Fly Air lightly coiled or ideally unrolled.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>