marta MT-2215 Hair Clipper Set User Manual

: June 13, 2024
: MARTA

Table of Contents

marta MT-2215 Hair Clipper Set
Product Information
Product Usage Instructions
Parts list
PRECAUTION
INSTRUCTIONS FOR HAIR CUTTING
TIPS
BLADES ALIGNMENT
CLEANING
BLADES LUBRICATION
SPECIFICATION
WARRANTY
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

marta MT-2215 Hair Clipper Set

Product Information

The Hair Clipper Set (Models: MT-2215, MT-2216, MT-2217) is a grooming tool designed for cutting and styling hair. It is equipped with various components including blades, a blade adjustment lever, housing, an on/off switch, a hanging loop, 4 removable combs, oil, and a brush for blade cleaning. The set is available in different variations depending on the country of purchase. The hair clippers operate on a power supply of 220-240V and 50Hz frequency. The net weight of the clippers is 0.32kg, and the gross weight is 0.40kg. The package size is 100mm x 65mm x 236mm. The product is produced by Cosmos Far View International Limited in Ningbo, China. It is important to note that the actual set of the appliance may differ from what is listed in the user manual, so it is recommended to check the contents before making a purchase. The producer reserves the right to change the complete set, appearance, country of manufacture, warranty, and technical characteristics of the model without notice.

Product Usage Instructions

Caution: Before using the hair clippers, it is important to read and understand the user manual.

Instructions for Hair Cutting:

Make sure the hair clippers are fully charged or connected to a power source.
Select the desired comb attachment based on the desired hair length.
Attach the selected comb to the housing of the hair clippers.
Turn on the hair clippers using the on/off switch.
Hold the hair clippers at a comfortable angle and start cutting the hair in the desired style.
Use the blade adjustment lever to adjust the cutting length if necessary.
After cutting, turn off the hair clippers and detach the comb attachment for cleaning.
Use the provided brush to clean the blades of any hair or debris.

Extra Combs: The hair clipper set includes 4 removable combs that can be used for achieving different hair lengths. Attach the desired comb to the housing of the hair clippers before cutting.

Blade Adjustment Level: The blade adjustment lever allows you to adjust the cutting length of the hair clippers. Move the lever up or down to increase or decrease the cutting length respectively.

Tips:

Start cutting from the bottom and work your way up for even results.
For a more precise cut, hold the hair clippers at a slight angle against the scalp.
Regularly clean and lubricate the blades for optimal performance and longevity.

Parts list

Blades
Blade adjustment lever
Housing
On / Off switch
Hanging loop
4 removable combs
Oil
Brush for blade cleaning
$marta-MT-2215-Hair-Clipper-Set-FIG-1 $1$$

PRECAUTION

CAUTION
Before the first use, check the device specifications and the power supply in your network.

The appliance is not intended for industrial or commercial use.
For indoor use only. Use only for domestic purposes according to the instruction manual.
Do not use it with a damaged cord, plug, or other injuries.
Keep the power cord away from sharp edges and hot surfaces.
Do not pull the cord. Always take the plug. Do not reel the cord around the device housing.
Never attempt to frame and repair the appliance by yourself. If you encounter problems, please contact the nearest customer service center.
Using accessories or replacement parts that are not recommended or sold by the manufacturer may cause damage to the appliance.
Always unplug the appliance and let it cool down before cleaning and removing parts. Keep unplugged if not in use.
To avoid electric shock and fire, do not immerse in water or other liquids. If that occurs, immediately unplug the appliance and contact the service center for inspection.
The appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
Never drop or insert any object into any opening on the appliance.
Make sure before use that blades are aligned properly.
Do not place the appliance on a surface while it is operating.
Do not use the appliance with a damaged or broken comb or with teeth missing from the blades as injury may occur.

NOTE: keep the blades oiled!

INSTRUCTIONS FOR HAIR CUTTING

Before starting a haircut cut inspect the clipper, and ensure that it is free of oil between the cutting blade teeth.
Switch the appliance on to distribute the oil and make sure it is running smoothly. Wipe off any excess oil.
While using the appliance, untwist the cord from time to time to avoid tangling.
Seat the person so that the head is at your eye level. That provides better control of haircutting.
Before cutting comb hair to ensure that there are no tangles.
Place a towel around the neck and over the shoulders of the person having the haircut.
- NOTE: When you use the hair clipper for the first time, the appliance may vibrate and make a snapping sound. This is normal and is a feature of the design.

EXTRA COMBS

Attachment comb № 1 leaves 3 mm hair length.
Attachment comb № 2 leaves 6 mm hair length.
Attachment comb № 3 leaves 9 mm hair length.
Attachment comb № 4 leaves 12 mm hair length.
To attach a comb hold it with its teeth upward and slide it onto and along the clipper blade until the front of the comb is firmly placed against the clipper blade.
When you use the clipper for the first time, cut only small portions of hair until you are accustomed to the cutting length with a certain comb attachment.
For even cutting, allow the comb attachment/cutter to cut its way through the hair. Do not force it through quickly. Also, remember to comb the hair frequently to remove trimmed hair and check for uneven strands.

BLADE ADJUSTMENT LEVEL

The lever of blade adjustment is located near your thumb (if you are right-handed) so it can easily be adjusted while the clipper is in your hand.
The blade adjustment level adds versatility to your clipper. It allows you to change gradually the length of your haircut without a comb.
When the level is in the upper position, the blades make the shortest cut.
Pushing the lever downward gradually you could increase the length of the haircut.
In the lowest position of the lever hair length is approximately the same as after № 1(3mm) comb.
The level also extends the use of your blades as different cutting edge is used in each setting.
To remove stuck hair move rapidly the lever from the lower to the upper position several times.
If your clipper stops cutting and removing stuck hair doesn’t help, replace the blades with new ones.

TIPS

Cut the hair in a relaxed and slow manner. Use short strokes only to work gradually over the head.
Always take off a little at a time.
Cut dry hair only as it is easier to control haircut length.
Don’t cut fast.
Don’t press hard on the clipper.
If you cut for the first time start with maximum comb attachment.

STEP 1 – NAPE AND NECK

Set № 1 (3 mm) or № 2 (6 mm) comb.
Hold the clipper cutting edge up and begin the haircut. Start at the center of the head at the base of the neck (fig. 1).
Slowly lead the clipper, working upwards and outwards, through the hair, trimming just a little at a time.
Continue to cut back area from the bottom of the neck upwards to the top of the ears.

STEP 2 – BACK OF THE HEAD

Set № 3 (9 mm) or № 4 (12 mm) comb and cut the back of the head (fig. 2).
STEP 3 – TEMPLES AND SIDE OF THE HEAD
Set № 1 (3 mm) or № 2 (6 mm) comb and cut hairs in temples area.
Set № 3 (9 mm) or № 4 (12 mm) comb and continue to cut hair to the top of the head (fig. 3).

STEP 4 – TOP OF THE HEAD

Set № 3 (9 mm) or № 4 (12 mm) comb and start to cut top of the head from back to front along the direction of normal hair growth (fig. 4).
Comb attachment № 1 (3mm) or № 2 (6mm) are used to achieve a close crew cut or short cut.
For longer haircut on the top of the head use the flat comb and lift hair on the top of the head. Cut over the comb, with the hair lifted or hold the hair between the fingers to lift it and cut it to desired length (fig. 5-6). Always start from the back of the head. You can cut the hair shorter gradually by reducing the space between the comb/fingers, and the head. Comb out trimmed hair and check for uneven strands.

STEP 5 – FINAL HAIR LEVELING

Finally, use the lowest blade adjustment level. You don’t need any comb. Trim hair around the base of the neck, sides of the neck and the ears with the clipper.
Reverse the hair clipper (fig. 7).
Press the clipper right angles to the head, tips of the blades lightly touching the skin and work downwards.

SHORT HAIRCUTS AND FLAT TOPS

Set № 4 (12 mm) comb and move the clipper from nape to the top of the head.
Hold the comb parallel to the head and slowly move the clipper through the hair as shown (fig. 8).
Cut the hair against the direction of their growth from the front to the top of the head. Then cut the side parts of the head.
For “flat top” use the flat comb, not attachments. Starts to cut from the top of the head lifting hair with the comb.
Using lower blade adjustment levels or smaller attachment combs cut hair to taper the hair down to the neckline.

BLADES ALIGNMENT

Blades must be realigned if they have been removed for cleaning or replacement.
To realign the blades simply match the upper and bottom blades teeth up, point for point.
The end of the top blade teeth should be approximately 1.2 mm back from the bottom blade. Compare your clipper blades with the figure.
If blades are set incorrectly, add a few drops of oil to the blades, switch on the clipper for a few seconds, then switch it off and unplug.
Loosen the screws slightly and adjust the blades. Tighten the screws after the blade is aligned.
If the hair clipper buzzes, then adjust it using the screws (on the device). Before adjusting the oil the blades.

CLEANING

Mind to clean the appliance regularly for appliance and blades long life.
Ensure that the appliance is switched off.
Remove cut hair from the blades with the brush.
Wipe the body of the hair clipper with a wet cloth. Dry the appliance.
Don’t immerse the appliance in water or another liquid.
Don’t use chemical or abrasive cleaners.

BLADES LUBRICATION

Mind to oil the blades of the clipper every few haircuts for appliance and blades long life.
Use only oil that is in the set.

SPECIFICATION

Model| Power supply| Net weight / Gross

weight

| Package size (L х W х H)
---|---|---|---
MT-2215

MT-2216 MT-2217

| 220-240 V, 50 Hz| 0,32 kg / 0,40 kg| 100 mm х 65 mm х 236 mm

Producer:

Cosmos Far View International Limited
Room 701, 16 apt, Lane 165, Rainbow North Street, Ningbo, China
Made in China

WARRANTY

WARRANTY DOES NOT COVER SUPPLIES (filters, ceramic and non-stick coating, rubber seals, etc.)

The production date is available in the serial number located on the identification sticker on the gift box and/or on the sticker on the device. The serial number consists of 13 characters, the 4th and 5th characters indicate the month, and the 6th and 7th indicate the year of device production. The producer may change the complete set, appearance, country of manufacture, warranty, and technical characteristics of the model without notice. Please check when purchasing the device.