JAMES ALLAN ZPL47810S Silver Roland 11 Tall LED Pier Mount Post Light Instruction Manual

JAMES ALLAN ZPL47810S Silver Roland 11 Tall LED Pier Mount Post Light

GENERAL

1. Be sure to read these instructions and review the diagrams thoroughly before beginning.
2. Electrical connections must be in accordance with local codes, ordinances, or the National Electric Code. If you are unfamiliar with methods of installing electrical wiring, secure the services of a qualified licensed electrician.
3. Before starting the installation, disconnect the power by turning off the circuit breaker or by removing the appropriate fuse at the fuse box. Turning the power off at the light switch is not sufficient to prevent electrical shock.

PREPARE THE FIXTURE

NOTE: First turn off the electricity
FINAL ASSEMBLY

1. Pull the black, white and ground wires out of the mounting post.

2. While supporting the fixture, connect electrical wires. If your post has a ground wire (green or bare copper), connect the fixture ground wire to it. If not, consult your electrician for proper grounding
   ELECTRICAL CONNECTIONS 120V~, 60Hz
   Connect white wire(s) from the fixture to white neutral wire from the supply circuit. Connect black wire(s) to black hot wire from the supply circuit. Connect green wire to green or bare wire or grounding screw on the mounting bracket. In all cases grounding conductor to earth must be used. Use UL/CSA- listed wire connects suitable for the size, type, and number of conductors. No loose strands or loose wires should be present. Secure wire connectors with UL /CSA-listed electrical tape. After the wires are connected, tuck them carefully inside the post cup.

3. Align the lantern with the mounting post and secure it with screws

4. Installation is complete. Turn on the power at the circuit breaker or fuse box. Turn the light switch on to activate the fixture.

5. LED replacement. Take down the finial(1), unscrew the decorative knobs(2), take down the one-shaped panel, unscrew the decorative knobs(3), take down glass(4), unscrew the screws(5), take down the heatsink, unscrew the LED screws(6) then pull out LED module, reapply the heat-conducting glue, finally replace LED module by the quick connector, secure the screws.

CAUTION: LED fixtures can operate at high temperatures please use caution when touching during operation or after operation.

ASSEMBLY AND INSTALLATION INSTRUCTIONS

WARNING: Be sure the electricity to the wires you are working on is shut off, either the fuse is removed or the circuit breaker is shut off.

NOTE: Before installing, consult local electrical codes for wiring and grounding requirements.

• Carefully remove the fixture from the carton, and check that all parts are included, as shown in the figure.
• Be careful not to misplace any of the screws or parts which are needed for installing the fixture.

Assembly and Installation Step:

1. Drill 4 holes 35mm deep for the Anchor sleeves and insert Wood screws so they are flush with the surface.
2. Place the Post of the Fixture to the Base, and then secure it with 3 Mounting Screws.

FOR YOUR SAFETY WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE IS REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF. GENERAL

You don’t need special tools to install this fixture. Be sure to follow the steps in the order given. Under no circumstances should a fixture be hung on house electrical wires, nor should a swag-type fixture be installed on a ceiling that contains a radiant-type heating system.
Read instructions carefully. If you are unclear as to how to proceed, consult a qualified electrician.
NOTE: Proper wiring is essential for the safe operation of this fixture

ASSEMBLY INSTRUCTIONS

READ & SAVE
INSTALLATION & OPERATION INSTRUCTIONS

TOOLS & MATERIALS REQUIRED

• Screwdriver
• Adjustable Wrench
• Wire Cutters
• Wiring Supplies

CAUTION

Prior to assembly, refer to the ELECTRICAL CONNECTIONS section. If you do not have electrical wiring experience, refer to a do-it-yourself wiring handbook or have your fixture installed by a qualified licensed electrician.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>