JASCO 55259 Z-Wave In-Wall Smart Fan Control Instruction Manual

JASCO 55259 Z-Wave In-Wall Smart Fan Control

Product Information

• Product Name: Z-Wave In-wall Smart Fan Control
• Model Number: 55259
• Brand: By Jasco Website: www.byjasco.com

Product Specifications

Requires neutral wire Switch must be mounted indoors Control fan motor only, not intended for lighting control No more than two fans – White/light almond paddles included Requires Z-Wave hub or controller (functions may vary depending on brand)

Installation Recommendations:

For single location wiring:

1. Connect the neutral wire, line, load, traveler, and ground wires according to the provided wiring diagram.
2. Mount the switch in the desired location.

For multi-location wiring:

1. Install a primary switch and add-on switch according to the provided wiring diagram.
2. Connect the neutral wire, line, load, traveler, and ground wires as indicated in the diagram.

Device Configuration:

To add the device to a Z-Wave network:

1. nsure that the Z-Wave hub is ready to add devices.
2. Press and release the top or bottom button on the smart fan control to add it to the network.

To remove and reset the device from the network:

1. Ensure that the Z-Wave controller is ready to remove devices.
2. Press and release the top or bottom button on the smart fan control to remove it from the network.

To return the device to factory defaults:

1. Quickly press the ON button three times.
2. Then, press the OFF button three times.
3. The LED on the device will flash ON/OFF five times when the reset is completed successfully.

Certifications & Compliances

FCC/IC certified – Complies with FCC RF exposure compliance requirements – Model: ZW4002/14314 – CAN ICES-3(B)/NMB-3(B)

Related Products
Z-Wave Smart Controls – Add-On Switch – In-Wall Smart Dimmer Motion Switch – In-Wall Smart Dimmer – In-Wall Smart Outlet

Important Note: To comply with FCC RF exposure compliance requirements, no changes to the antenna or the device are permitted. Any changes may result in the device exceeding RF exposure requirements and void the user’s authority to operate the device.

Warning: – Risk of fire – Risk of electrical shock – Risk of burns

Distributed By: Jasco Products Company LLC, 10 E. Memorial Rd., Oklahoma City, OK 73114.

Product Usage Instructions:

1. Ensure that you have a neutral wire available for installation.
2. Mount the Z-Wave In-wall Smart Fan Control indoors in the desired location.
3. Connect the wires according to the provided wiring diagram for either single-location or multi-location wiring.
4. If using multi-location wiring, install a primary switch and add-on switch.
5. Once the installation is complete, ensure that you have a Z-Wave hub or controller ready to add devices.
6. Press and release the top or bottom button on the smart fan control to add it to the Z-Wave network.
7. To remove the device from the network, press and release the top or bottom button on the smart fan control when the Z-Wave controller is ready to remove devices.
8. To reset the device to factory defaults, quickly press the ON button three times, then press the OFF button three times. The LED on the device will flash ON/OFF five times when the reset is completed successfully.
   Note: For any further assistance or troubleshooting, refer to the provided user manual or visit the website www.byjasco.com.

DIMENSION

Specifications

• Power: 120VAC, 60Hz Signal Frequency: 908.4/916 Maximum Fan Motor Load: 2.5A
• Range: Up to 150 feet from controller or closest Z-Wave device Operating Temperature: 32-104° F (0-40° C)
• Warranty: 5-year limited product warranty Requires neutral wire. Switch must be mounted indoors Control fan motor only, not intended for lighting control. No more than two fans

Design Features

• Remotely monitor with any mobile device*
• May be used in single pole installation or with up to four Jasco model 46560 Add-on switches in 3, 4, 5 or 6-way wiring configurations
• Turn ON/OFF and control speed level of the connected Ceiling fan manually or via Z- Wave remote control (On/Off, High, Medium, Low)
• Can be Included in multiple Groups and Scenes
• Supports Advanced Configuration; LED status, Invert switch (if unit is installed upside down)
• Screw Terminal installation; requires wiring connections for Line (Hot), Load, Neutral and Ground. Traveler wire required for multi pole installation
• Use a standard size wall plate for single gang installations (wallplate not included)
• Interchangeable Paddle switch: White & light almond paddle included in package
• LED can be enabled/disabled manually
• Inline traveler circuit protection

Z-Wave Plus Features

• Improved battery life and up to 50% more wireless range
• 250% faster processor
• 400% more memory
• 50% more energy efficient
• Supports wireless upgrades to future-proof your home

White/light almond paddles included

• Requires Z-Wave hub or controller, functions may vary depending on brand.

55259 PRODUCT SPECIFICATIONS

Single Location Wiring

Space-Saving Screw Terminals

Multi-Location Wiring

Installation Recommendations

• Devices require a 1-gang U.S. wall box. 3½ in deep recommended, 2¼ in deep minimum.
• Indoor use only
• Visit http://www.ezzwave.com/hubs/ for hub compatibility
• Wallplates sold separately
• Trilingual Instruction manual – (English, French, Spanish)

Device Configuration

• Adding your device to a Z-Wave network
  Once the hub is ready to add your smart fan control, press and release the top or bottom button on the smart fan control to add it in the network.

• To remove and reset the device
  Once the controller is ready to remove your device, press and release the top or bottom button on the smart fan control to remove it from the network.

• To return to factory defaults
  Quickly press the ON button 3 times, then press the OFF button 3 times.The LED will flash ON/OFF 5 times when completed successfully

Certifications & Compliances

Compliances, specifications and availability are subject to change without notice Distributed by Jasco Products Company LLC 10 E. Memorial Rd., Oklahoma City, OK
Questions? Contact our U.S.-based Consumer Care at 1-800-654-8483 between 7AM-8PM, M-F, Central Time.
©Jasco 2020

Related Products – Z-Wave Smart Controls

Additional Paddle Colors

FCC/IC

This device complies with Part 15 of the FCC and Industry Canada license- exempt RSS standards. Operation is subject to the following two conditions:

1.  this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Important note: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device.

READ IT OR WATCH IT

Read instructions or watch easy-to-follow video. Scan QR code or visit goo.gl/hEdRhS

Purchase additional items at EZzwave.com or visit your local retailer.

DO NOT RETURN THIS PRODUCT TO THE STORE

Questions? Contact our U.S.-based Consumer Care at 1-800-654-8483 between 7AM-8PM, M-F, Central Time.
For the most up-to-date product support, accessories, electronic (PDF) format manuals and more, visit www.byjasco.com/support.

WARNING

• RISK OF FIRE
• RISK OF ELECTRICAL SHOCK
• RISK OF BURNS
• CONTROLLING APPLIANCES:
• CONTROL FAN MOTOR ONLY (FOR USE ONLY WITH SPLIT-CAPACITOR OR SHADED-POLE CEILING FAN MOTORS).
• DO NOT USE Z-WAVE DEVICES TO CONTROL ELECTRIC HEATERS OR ANY OTHER APPLIANCES WHICH MAY PRESENTA HAZARDOUS CONDITION DUE TO UNATTENDED OR UNINTENTIONAL OR AUTOMATIC POWER ON CONTROL.

WARRANTY

Jasco Products Company warrants this product to be free from manufacturing defects five years from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this product. This warranty is in lieu of all other warranties, expressed or implied. Some states do not allow limitations on how long an implied warranty lasts or permit the exclusion
or limitation of incidental or consequential damage, so the above limitations may not apply to you. This warranty gives you specific rights, and you may also have other rights which vary from state
to state. Please contact our U.S.-based Consumer Care at 1-800-654-8483 (option 1) between
7AM – 8PM CT or www.byjasco.com if the unit should prove defective within the warranty period.

Jasco Products Company LLC, Building B 10 E. Memorial Rd. Oklahoma City, OK 73114.

SPECIFICATIONS

ZW4002

• Power: 120VAC, 60Hz | Signal (frequency): 908.4/916MHz
• Maximum loads: 2.5A no more than two identical fans to the switch. Not to exceed 2.5A resistive load. CONTROLS FAN MOTOR ONLY. For use only with split-capacitor or shaded-pole ceiling fan motors
• Range: Up to 150ft. line of sight between the wireless controller and the closest Z-Wave receiver module.
• Operating temperature range: 32-104° F (0-40° C)
  For indoor use only
  Specifications subject to change without notice due to continuing product improvement

Tools you will need

IMPORTANT!
No more than two identical fans to the smart switch. Not to exceed 2.5A resistive load. CONTROLS FAN MOTOR ONLY. For use only with split-capacitor or shaded-pole ceiling fan motors.

Getting to know your new Z-Wave device

• Turn ON/OFF and adjust fan speed levels manually or remotely via the Z-Wave controller
• Can be included in multiple groups and scenes
• May be used in single-pole installation or with up to two Jasco add-on switches in 3-way or 4-way wiring configurations
• Interchangeable paddle switch — white & light almond paddle in package Uses a standard, rocker-style wallplate for single-gang installations (wallplate not included)
• Blue LED indicates switch location in a dark room
• Z-Wave certified for simple pairing and integrated home automation
• Screw terminal installation — requires wiring connections for line (hot), load, neutral and ground. Traveler wire required for 3-way or 4-way installation
• This Z-Wave device has advanced features that allow you to customize your experience. These features can only be adjusted by a Z-Wave enabled controller that supports the Z-Wave configuration command class. For a complete list of adjustable configurations, visit www.byjasco.com/z-waveconfig

PRODUCT OVERVIEW

• A. Ground (Green/Bare)
• B. Load (Black)
• C. Line (Black)
• D. Traveler (Red/Other)
• E. Neutral (White)
• F. Top Rocker — Press & release to turn fan on, press & hold to increases speed
• G. Bottom Rocker — Press & release to turn fan off, press & hold to decrease speed

Multiple-gang boxes
When installing the smart fan control in multiple-gang boxes it may be necessary to break off one or both sides of the scored tabs on the front yoke. This does not affect the electrical rating of the switch (see specifications for details).

WARNING — SHOCK HAZARD
Turn OFF the power to the branch circuit for the switch and fixture at the service panel. All wiring connections must be made with the POWER OFF to avoid personal injury and/or damage to the switch. This device is intended for installation in accordance with the National Electric Code and local regulations in the United States, or the Canadian Electrical Code and local regulations in Canada. If you are unsure or uncomfortable about performing this installation consult a qualified electrician.

Multi-switch wiring
For 3-way installations, please refer to add-on switch manual

Single-switch wiring
Before installation, you may wish to change the paddle color to match your wallplate or décor. Please proceed to section 5.

1. Shut off power to the circuit at circuit breaker or fuse box.
   IMPORTANT! Verify power is OFF to switch box before continuing.

2. Remove wallplate.

3. Remove the switch mounting screws.

4. Carefully remove the switch from the switch box. DO NOT disconnect the wires.

5. There are five screw terminals on the fan control; these are marked:

   • A. GROUND – Green/Bare
   • B. L OAD – Black (connected to fan)
   • C. L INE (Hot) – Black (connected to power)
   • D. TRAVELER – Red/Other (only in 3-way installations)
   • E. NEUTRAL – White Match these screw terminals to the wires connected to the existing switch.

6. Disconnect the wires from the existing switch. Label wires according to the previous

Observe important wiring information

IMPORTANT! This fan control is rated for and intended to only be used with copper wire.

Wire gauge requirements
Use 14AWG or larger wires suitable for at least 80° C for supplying line (hot), load, neutral, ground and traveler connections.

Wire strip length
For attachment using the enclosure’s holes, strip insulation 5/8in. (16mm).
UL specifies the tightening torque for the screws is 14Kgf-cm (12bl f-in.).

1. Connect the green or bare copper ground wire to the GROUND terminal.

2. Connect the black wire from the fan to the LOAD terminal.

3. Connect the black wire from the electrical service panel (hot) to the LINE terminal.

4. Connect the white wire to the NEUTRAL terminal (use jumper wire if needed).
   Note: The traveler terminal is only used for 3-way or 4-way wiring and should not be connected if the fan control is installed in a 2-way system (one switch & one load).

5. Insert fan control into the switch box being careful not to pinch or crush wires.

6. Secure the fan control to the box using the supplied screws.

7. Mount the wallplate.

8. Reapply power to the circuit at fuse box or circuit breaker and test the system.

Basic operation
Note: Before starting, fan must be set to HIGH position using pull chain.
The connected fan can then be turned ON/OFF and adjust speed levels in two ways:

1. Manually from the front panel of the fan control.
2. Remotely with a Z-Wave controller.

Manual control

1. To turn the connected fan ON, press and release the top of the orcker.
Note: Fan will return to last speed setting of the fan control – default = HIGH.
2. To turn the connected fan OFF, press and release the bottom of the rocker.

Adjust fan speed
The LED indicator confirms fan speed settings by flashing patterns:

• LOW – Blinks every two seconds for 10 seconds
• MEDIUM – Blinks every second for 10 seconds
• HIGH – Blinks every half second for 10 seconds

1. To increase fan speed, press and hold the top of the rocke.r
2. To decrease fan speed, press and hold the bottom of the rocke.r
   Note: The smart device only controls the fan motor and does not control any lighting connected to the fan. If your fan has an integrated light, a second switch needs to be installed to control the lighting directly. No more than two identical fans should be connected to the fan control. The total load of the fan(s) should not exceed 2.5A.

Adding your device to a Z-Wave network

1. Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave network.

2. Once the controller is ready to add your device, press the topo r bottom rocker of the fan control.
   You have complete control to turn your fan ON/OFF and adjust speed according to groups, scenes, schedules and interactive automations programmed by your controller.
   If your Z-Wave certified controller features remote access, you can control your fixture from your mobile devices.
   If prompted by the controller to enter the S2 security code, refer to the Verify this product supports S2/SmartStart QR code/security number on the side of the box or the QR code label on the product (see Figure

3. Enter the 5-digit pin code

To remove and reset the device

1. Follow the instructions for your Z-Wave certified controller to remove a device from the Z-Wave network.
2. Once the controller is ready to remove your device, press and release the top or bottom rocker of the fan control.

To return your switch to factory defaults
Quickly press ON (top) button three times. Then, immediately press the OFF (bottom) button three times. The LED flashes ON/OFF five times when completed successfully.
NOTE: This should only be used in the event your networks’ primary controller is missing or otherwise inoperable.

To change color of the paddle

This step is optional. Before installation, you may want to change the color of the paddle to match your wallplate or décor.

1. Lift the air gap tab at the base of the paddle.
2. Push the side tabs in on one side and then the other to reealse paddle. Lift the cover up and of.
3. Simply put the new paddle onto the fan control by insertingt he air gap and side tabs and snapping securely into place.
   Once this step is complete, return to section 3.

The Jasco add-on switch is required for multi-switch 3-way or 4-way installations. Connecting the traveler terminal of this switch to a standard, non-Jasco switch will cause damage or result in improper function. If this switch is part of a multi-switch installation, do not connect the traveler wire or apply power until Jasco add-on switches are correctly installed. For more information on multi-switch installations, view the Jasco add-on switch manual.

Z-WAVE INTEROPERABILITY
This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.

This device supports Association Command Class (3 Groups)

• Association Group 1 supports Lifeline, Switch Multilevel Report
• Association Group 2 supports Basic Set and is controlled by pressing the ON or OFF button with the local load
• Association Group 3 supports Basic Set and is controlled by double pressing the ON or OFF button
• Each Association Group supports 5 total nodes

References

• Z-Wave by Jasco
• Jasco
• Support
• Z-Wave Hubs

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>