TARAMPS TS 400X4 4 Channels 400 Watts Rms Car Audio Instruction Manual

TARAMPS TS 400X4 4 Channels 400 Watts Rms Car Audio

Product Information

The Amplifier is a Taramps product with a power output of 400Watts at 2 Ohms, providing 4 x 100W RMS. It belongs to the aftermarket product family and is designed for use with electronic equipment in vehicles. The amplifier has a crossover feature with options for LPF (Low Pass Filter), HPF (High Pass Filter), and FULL. It also has LED indicators for easy monitoring. The amplifier is compact in size, measuring 138 x 49 x 121mm and weighs 0.60Kg. It operates within a frequency range of 18Hz to 30KHz. The amplifier requires a 12V to 16VDC power supply and has an input sensitivity of 200mV. It is designed to dissipate heat effectively with its aluminum chassis acting as a heatsink.

Product Usage Instructions

1. Before using the amplifier, carefully read the user manual and familiarize yourself with its features and specifications.
2. Connect the amplifier to the RCA outputs of your Head Unit using good quality shielded cables to minimize noise interference.
3. Set the amplifier’s input sensitivity using the LEVEL control. This allows for optimal adjustment to the output signal levels of your Head Unit.
4. Choose the desired operating mode of the amplifier’s crossover by selecting either LPF (Low Pass Filter), HPF (High Pass Filter), or FULL.
5. Use the CROSSOVER controls to set the frequency range for the selected operating mode. The available frequency range is from 18Hz to 30KHz.
6. Ensure that the amplifier is connected to a stable power supply within the specified voltage range of 12V to 16VDC.
7. Pay attention to the LED indicators on the amplifier to monitor its status and performance.
8. Take caution when connecting the amplifier’s inputs and outputs, ensuring that the negative (-) terminal is properly connected to avoid any loss of signal or damage.
9. It is recommended to use Taramps RCA cables for optimal performance.
10. The amplifier’s aluminum chassis acts as a heatsink, dissipating heat when the amplifier is in use. Ensure proper ventilation for efficient heat dissipation.
11. For any technical assistance or further information, refer to the provided contact details in the user manual or visit the manufacturer’s website.

Term of warranty

TARAMPS, located on Abilio Daguano Street 274, Res. Manoel Martins – Alfredo Marcondes, SP – Brazil,ZIP CODE 19180-000, guarantees this product against any defects on terms of project, making,assembling, and/or with solidarity, due to project vices which cause it improper or inadequate to its original use within 12 months from the date of purchase. In case of defect during the warranty period,TARAMPS responsibility is limited to the repairing or substitution of the device of its own making.

This warranty excludes:

• Damaged products by improper installation, water infiltration, violation by unauthorized individuals;

• Tamper or torn warranty seal;
  Cases in which the product is not used in adequate conditions;

• Defects caused by accessories, modifications or features attached to the product;

• The product with damage from falling, bumps or nature related problems (flooding, lightning, etc.);

• Warranty card is not properly filled or torn;

• Costs involving uninstallation, reinstallation of equipment as well as shipment to the factory;

• Damage of any kind, due to problems in the product, as well as losses caused by discontinued use of the product.

Technical assistance

For international support, check on our website: www.taramps.com.br/en/rede- de-assistencias-tecnicas or contact direct the factory support:
Phones: +55 18 3266-4050 / +55 18 99749-3391
E-mail: service@taramps.com.br

Introduction
Read this manual before preparing the product. In case of doubt, contact our technical support: (18) 3266-4050 or www.taramps.com.br.
At the end of its useful life, this product must not be disposed of in household waste. Look for an electronic equipment collection or recycling center for proper disposal.

Declaration of Conformity
TARAMPS ELECTRONICS LTDA
Alfredo Marcondes – SP
Brazil

Hereby, Taramps Electronics Ltda declares that the product TS 400X4 complies with the Directive 2014/30/EU, according with the following harmonized standard:
-EN 50498:2010 Electromagnetic compatibility (EMC) -Product family standard for aftermarket electronic equipment in vehicles
The full text of the EU Declaration of Conformity is available at the following Product Page on Internet.

Safety requirements

To ensure proper use, please read through this manual before using the amplifier. It is specially important that you know the WARNINGS and CAUTIONS contained here.

• The installation of this amplifier must be done by a qualified professional.

• Wear safety glasses, insulated gloves and correct tools for installing this product.

• This amplifier is for use with 12V batteries. Always check the voltage before installing.

• This amplifier must be installed in a firm place with at least 1″ space around the heatsink for proper heat spreading.

• Never install the amplifier in places exposed to dust, humidity and water. Pay attention to install it far from fuel tank, fuel lines, heat sources and other parts of vehicle.

• Be sure to install protection fuse or a circuit braker near to battery. Follow the ampere rating as indicated here in this manual. Use of improper fuse or circuit breaker could result in overheat, smoke, damage to product, injury or burns.

• Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through car’s body.

• Before make any connection to amplifier, disconnect the battery negative terminal.

• When in use, the external surface of may amplifier becomes hot. Avoid touching the heatsink area and keep childrens far from the amplifier.

• This amplifier may produce high sound pressure levels. Avoid continuous exposure to levels over 85dB to prevent permanent hearing loss.

• Output connections for speakers may have voltage levels when the amplifier is operating.
  Make sure that the amplifier is turned OFF before proceed any connection or disconnection in this terminals.

• If you want to dispose this amplifier, don’t throw it on domestic waste. It must be collected by an used electronic product disposal service for proper recycling.

Safety

As you read this manual, pay attention to the safety symbols.

CAUTION
This symbol with “CAUTION” is intended to alert the user to the presence of important instructions. Failure to heed the instructions will result in risk of injury to user or product damage.

Taramps reserves the right to modify the contents of this document at any time without prior notice and does I not have the obligation to apply the changes in units which were previously produced.

Functions & inputs

1. INPUT: Inputs of signals to be amplified. Connect these signals to RCA outputs of Head Unit, using good quality shielded cables to avoid noise interference.
2. LEVEL: It sets the amplifier input sensitivity, which allows an optimal adjustment to the output signals levels of nearly all models of Head Units found in the market.
3. CROSSOVER: Set the operating mode of amplifier:

SELECTOR POSITION – FULL
Amplifies the whole audio range, responding from 18Hz to 30KHz. This function is normally used when there is an external crossover in the system.

SELECTOR POSITION – HPF – (HIGH PASS)
Amplifies signals with more intensity above 90Hz. This type of function is used mid-bass, mid-range speakers or tweeters.

SELECTOR POSITION – LPF – (LOW PASS)
Amplifies only bass signal, the response is limited to 90Hz (-12dB/8ª), an optimal frequency cutoff for sub-woofers.

LED indicator

ON: Indicates that amplifier is on.

Output & power supply connector

1. POWER (Power Supply Connector): The connector terminal (+) must be connected to the battery’s positive pole with a 4mm (minimum) wire gauge. The connector terminal (-) must be properly connect to the battery’s negative pole with a same wire gauge. The remote terminal must be connected to the Head Unit REMOTE output with a 0.75mm’ wire.
2. OUTPUT: To connect the speakers. Follow the polarity and the minimum impedance recommended.
   For STEREO connections, the minimum impedance is 2 ohms at each channel; for BRIGDED connections is 4 ohms.
   To combine speakers, the resulting impedance must be taken in consideration.
   See the examples below:

CAUTION
Before making any connections to the power terminals, make sure that the negative (-) ofthe vehicle battery is disconnected.

Protection system

Short-circuit Protection: Shutdown the amplifier when detect a short- circuit or impedance lower than the supported at the output.
Thermal Protection: The amplifier will shutdown if the heatsink gets too hot. Check the installation (speakers impedance, hot places or wrong installation).

Installation

CAUTION: All connections to power supply, input and output connectors must be carried out only with amplifier off.

Recommended wire gauge & fuse

• Positive/negative power supply cable ____ 11 AWG
• Output cables wire gauge___15 AWG
• Remote cable ____ 18 AWG
• Protection fuse or circuit breaker_____20A

Calculated considering a maximum length of 4m. Distance greater than this, you will need to increase the cable gauges.

CAUTION

• Using wire gauges below the recommendation will result in power loss and overheating of wiring.
• Check polarity and never reverse power supply cables due to the risk of damage to the amplifier.
• It is compulsory to install a protection fuses or circuit breakers as close as possible from batteries.

CAUTION

• The entire aluminum surface of the amplifier serves as a heat sink. The usually working temperature is 65°C. So, avoid contact with this surface when the amplifier is in use.
• This equipment is not suitable for use in places where children may be present.

Connection example in the output: Stereo + Bridged

Note: In case of compression driver and tweeters you must install a passive filter in the positive terminal of the same ones (Consult transducer’s manufacturer manual).

Technical features

Rated power at 1KHz, resistive load at the indicated impedance, with THD ≤ 10% and V = 13.8V.
Due to the natural tolerances of the internal components of the manufacturing process, the technical characteristics presented here may vary.

+55 18 3266-4050
Fabricado por / Manufactured by:
TARAMPS ELECTRONICS LTDA
CNPJ / TAX ID: 11.273.485/0001-03
Res. Manoel Martins
Alfredo Marcondes – SP
Indústria Brasileira – Made in Brazil
www.taramps.com.br

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>