FIBERROAD FR-7T4408BT Layer 3 Managed Industrial PoE Switch Instruction Manual

FIBERROAD FR-7T4408BT Layer 3 Managed Industrial PoE Switch

Product Information

The Layer 3 Managed Industrial PoE Switch is a high-performance network switch designed for industrial environments. It offers advanced features and reliable performance to meet the demands of industrial applications.

Main Features :

• Layer 3 Managed
• Industrial PoE Switch
• Operation Temp: -40~75°C
• Surge Protection
• IP40 RATED

Product Specifications:

Ethernet Interface Model Ports:

• FR-7T4408P: 8 PoE Ports
• FR-7T4408BT: 8 PoE Ports with extended power capabilities

Port Mode(Tx): Auto-Negotiation Full/Half Duplex Mode

Standards:

• IEEE 802.3 for 10BaseT
• IEEE 802.3u for 100BaseT(X) and 100BaseFX
• IEEE 802.3ab for 1000BaseT(X)
• IEEE 802.3z for 1000BaseSX/LX/LHX/ZX
• IEEE 802.3bz for 2.5G Ethernet
• IEEE 802.3ae for 10 Gigabit Ethernet
• IEEE 802.3x for flow control
• IEEE 802.1D-2004 for Spanning Tree Protocol
• IEEE 802.1w for Rapid Spanning Tree Protocol
• IEEE 802.1s for Multiple Spanning Tree Protocol
• IEEE 802.1p for Class of Service
• IEEE 802.1Q for VLAN Tagging
• IEEE 802.1X for authentication
• IEEE 802.3ad for Port Trunk with LACP
• Packet Buffer Size: 12Mbits
• Maximum Packet Length: Up to 10K
• MAC Address Table: 16K
• Transmission Mode: Store and Forward (full/half duplex mode)
• Exchange Property: Delay time < 7s, Backplane bandwidth:128Gbps
• IGMP Group: 4096
• Max. No. of VLAN: 256
• VLAN ID Range: VID 1 to 4094

PoE & Power Supply Model:

• FR-7T4408P PoE Ports: 1-8, Power Supply Pin: Default: 1/2(+), 3/6(-), IEEE802.3 af/at, Max Power Per Port: 30W, Total PWR / Input Voltage: Model dependent (240W with DC48-56V)
• FR-7T4408BT PoE Ports: 1-8, Power Supply Pin: Default: 1/2(+), 3/6(-), 4/5(+), 7/8(-), IEEE802.3 af/at/bt, Max Power Per Port: 90W, Total PWR / Input Voltage: Model dependent (360W with DC48-56V)

Power Consumption: 24 Watts Max (without PoE load)

Power Inputs:

• Non-PoE Mode: 9-56VDC
• PoE Mode: 48-56VDC (30W PoE Mode), 52-56VDC (90W PoE Mode)

Input Voltage Operating Voltage: 9-56VDC, Redundant dual inputs

Connector Protection: Overload Current Protection, Reverse Polarity Protection

Software Features:

• Management Interface: Local, SNTP, NTP
• Management File Management
• Management Access Filter
• Redundant Network
• VLAN Time Management
• Unicast Routing
• QOS
• ACL Type
• POE Management
• Diagnostic Maintenance
• Security
• MIB

Physical Characteristics:

• Housing: Aluminum case
• IP Rating: IP40
• Dimensions: 138mm x 108mm x 49mm (L x W x H)
• Installation: DIN Rail/Wall Mount
• Weight: 680g

Environmental:

• Operating Temperature: -40~75°C

• Operating Humidity: 5%~90% (non-condensing)

• Storage Temperature: -40~85°C

• MTBF: 1,043,909 hours @ Telcordia SR-332 Standard

• Heat Dissipation: 34 BTU/h (Non-PoE Model), 853 BTU/h (with
  240W PoE Load), 1262 BTU/h (with 360W PoE Load)

• Cooling: Fanless

• Noise Level: N/A

Product Usage Instructions

To use the Layer 3 Managed Industrial PoE Switch:

1. Ensure that the switch is installed in a suitable location, following the installation guidelines provided in the user manual.
2. Connect the Ethernet devices to the appropriate ports on the switch using Ethernet cables.
3. If using PoE functionality, connect the power input to the switch using the provided terminal blocks and ensure correct polarity.
4. Power on the switch by connecting it to a power source within the specified voltage range.
5. Configure the switch settings and management features using the provided management interface, such as Local, SNTP, or NTP.
6. Monitor and manage the switch performance and network connectivity through the management access filters, VLAN configurations, unicast routing, QoS settings, and other software features.
7. If necessary, perform diagnostic maintenance tasks and troubleshoot any issues using the available diagnostic tools and features.
8. Ensure proper security measures by configuring access control lists (ACLs), managing PoE operations, and implementing other security features supported by the switch.
9. Maintain and monitor the switch’s performance, environmental conditions, and heat dissipation to ensure optimal operation.

For detailed instructions and further information, refer to the complete user manual provided with the product.

L3 Managed Industrial PoE Switch is a multi-port, high-standard Industrial Managed PoE Ethernet Switch independently developed by Fiberroad for industrial ethernet network. This product adopts industryleading technical standards and can provide stable and reliable Ethernet transmission with high- quality design and reliability. They are designed in a rack mount aluminum housing and have 8Gigabit Ethernet ports ,21.25G/10G and 2×1.25G/2.5G/10G SFP/SFP+ Ports, supports Layer 3 routing functionality to facilitate the deployment of applications across networks. As a result, it can supply power to PD terminal equipment like wireless AP, webcam, VoIP, and IIoT Devices intercom through network cable and meet the infrastructure requirements of a high-density PoE/PoE+/PoE++ supply.

Main Features

• IEEE 802.3af/at/bt PoE++ Standard, without damaging not-PoE devices.
• Advanced PoE management functions : PoE output setting, Smart PoE, PoE scheduling and PoE Budget Management.
• Priority system for PoE Port, it will supply power to the high priority level port first when the power budget is insufficient.
• Layer 3 Model support OSPFv2, RIPv2, Static Route
• TACACS+, SNMPv3, IEEE 802.1X, HTTPS and SSH to enhance network security
• Link Aggregation, STP/RSTP/MSTP/ERPS for network redundancy
• ROMON for proactive and efficient network monitoring
• Fanless, IP40 Rating, -40 °C ~ 75℃ operation temperature design to ensure that the equipment adapts to a variety of harsh environments
• Redundant dual DC/AC power supplies are optional, anti-reverse connection, overcurrent protection
  Industrial Ethernet switches adopt mature technologies and open standards. They are equipped with a redundant power supply, high-temperature resistant, anti-electromagnetic interference, lowtemperature resistance, anti-vibration, and anti-shake features. They can also operate at -40 to 75°C and have 19” rack mounts that meet IP 40 protection standards. Industrial Ethernet switches are perfect for harsh environments such as military, utility market applications, and industrial networking.

Product Specifications

Ethernet Interface|
---|---
Model| FR-7T4408P/FR-7T4408BT
Ports| 2×1G/2.5G/10 Gigabit SFP (Port 9 and Port 11） 2x1G/10 Gigabit SFP+ （Port 10 and Port 12） 8×10/100/1000M Base-TX
Port Mode(Tx)| Auto-Negotiation Full/Half Duplex Mode

Auto MDI/MDI-X Connection

Standards

| IEEE 802.3 for 10BaseT

IEEE 802.3u for 100BaseT(X) and 100BaseFX IEEE 802.3ab for 1000BaseT(X)

IEEE 802.3z for 1000BaseSX/LX/LHX/ZX

IEEE 802.3bz for 2.5G Ethernet IEEE 802.3ae for 10 Gigabit Ethernet

IEEE 802.3x for flow control

IEEE 802.1D-2004 for Spanning Tree Protocol IEEE 802.1w for Rapid Spanning Tree Protocol IEEE 802.1s for Multiple Spanning Tree Protocol IEEE 802.1p for Class of Service

IEEE 802.1Q for VLAN Tagging IEEE 802.1X for authentication

IEEE 802.3ad for Port Trunk with LACP

Packet Buffer Size| 12Mbits
Maximum Packet Length| Up to 10K
MAC Address Table| 16K
Transmission Mode| Store and Forward (full/half duplex mode)
Exchange Property| Delay time: < 7μs

Backplane bandwidth: 128Gbps

IGMP Group| 4096
Max. No. of VLAN| 256
VLAN ID Range| VID 1 to 4094

Software Features

Physical Characteristics

853 BTU/h(with 240W PoE Load)

1262 BTU/h(with 360W PoE Load)

Cooling| Passive Cooling, Fanless Design
Noise Level| 0 dBA
LED| State| Description
---|---|---
PWR (P1 &P2)| ON| Power is being supplied
OFF| Power is not being Supplied.
RUN| Blinking| The system is running well

Link/ACT (1-12)

| ON| Port connection is active
Blinking| Data transmitted
OFF| Port connection is not active.

RJ45 Port Speed

| ON| 1000M is running
OFF| No 1000M is running

ALM

| ON| Has alarm information
OFF| No alarm information

Certification Standard

EMC/EMI/EMS

| FCC Part15 Class A CE-EMC/LVD

RoHS

EN61000-4-2 (ESD):LEVEL 4

IEC 6100-4-2 (EFT):LEVEL 4

IEC 6100-4-2 (Surge): LEVEL 4

IEC 6100-4-2 (CS)：LEVEL 3 IEC 61000-4-2(PFMP) : LEVEL 5 EN61000-4-3 (RS):LEVEL 4

---|---
| IEC60068-2-27
Shock|
Vibration| IEC60068-2-6
Freefall| IEC60068-2-31
Safety| EN 60950-1, UL 60950-1, CSA C22.2 No.60950-1, UL 508

Package Contents

2x Wall-Mount Kits

Documentation

| 1 x Quick Start Guide

1 x Warranty card 1x Product notice

Dimensions

Accessories

(Sold Separately)

Power Supply|
---|---
FR-I-40-24| DIN-rail 24 VDC power supply with 40W/1.7A, 85 to 264 VAC, or 120 to 370 VDC input, -20 to 70°C

operating temperature

FR-I-60-24| DIN-rail 24 VDC power supply with 60W/2.5A, 85 to 264 VAC, or 120 to 370 VDC input, -20 to 70°C operating temperature
SFP Optical Transceiver|
---|---
FRSX-1L311C-I| 1.25Gb/s 1310nm 10km SFP, wide operation temperature range of -40℃-85℃（-40℉ – 185℉）
FRSX-1L341C-I| 1.25Gb/s 1310nm 40km SFP，wide operation temperature range of -40℃-85℃（-40℉ – 185℉）
FRSX-1L5X1C-I| 1.25Gb/s 1550nm 80/100km SFP，wide operation temperature range of -40℃-85℃（-40℉ – 185℉）
FRSX-1L3523/5323C-I| 1.25Gb/s 1310nm/1550nm 20km BiDi SFP，wide operation temperature range of -40℃-85℃（-40℉ – 185℉）
FRSX-AL1N2C-I| 10 Gb/s 850nm 300m SFP+, wide operation temperature range of -40℃-85℃（-40℉ – 185℉）
FRSX-AL311C-I| 10 Gb/s 1310nm 10km SFP+, wide operation temperature range of -40℃-85℃（-40℉ – 185℉）
Armored Fiber Patch Cable / LAN Cable

FRPC-A-LC| Armored LSZH LC UPC to LC UPC Duplex OS2 single mode 7.0mm for Ourdoor Application , 1-50m
FRLC-A-CAT6| Armored Cat6 Snagless shielded(SFTP) Ethernet Network Patch Cable, 26AWG, 1000Base-T, 0.5m – 3m

Precautions

To avoid damage to the equipment and personal injury caused by improper use, please observe the following precautions:

-Keep the power off during installation, wear an anti
static wrist, and ensure that the anti static
wrist is in good contact with the skin to avoid potential safety hazards.

• The switch can work normally under the correct power supply. Please confirm that the power supply voltage matches the v oltage indicated by the switch.
• Before powering on the switch, please make sure that the power circuit is not overloaded, so as not to affect the normal operation of the switch and even cause unnecessary damage.
• To avoid the risk of electric shock, do not open the case while the switch is working, even if it is not charged, do not open it yourself.
• Before cleaning the switch, pull out the power plug of the switch. Do not wipe with a wet cloth. Do not use liquid to clean it.
• The equipment installed in the rack is generally from bottom to top to avoid overload installation.
• Avoid placing other heavy objects on the surface of the switch to avoid accidents.

Order Information

Model Number| 10/100/1000Bas e-T(X), RJ45| 1.25G/10G

SFP/SFP+ Port (Port 10 and 12)

| 1.25G/2.5G/10G

SFP/SFP+ Port (Port 9 and 11)

| Optical Port Connector Option| PoE Ports & Standard| Input Voltage| Operating Temp.
---|---|---|---|---|---|---|---
FR-7T4408| 8| 2| 2| LC| —| DC9-56V| -40 to +75℃

FR-7T4408P

| ****

8

| ****

2

| ****

2

| ****

LC

| Port 8-24 IEEE802.3 af/at| ****

DC9-56V

| -40 to +75℃

FR-7T4408BT

| ****

8

| ****

2

| ****

2

| ****

LC

| Port 8-24 IEEE802.3 af/at/bt| ****

DC9-56V

| -40 to +75℃

The information in this document is subject to change without notice. Fiberroad has made all effects to ensure the accuracy of the information, but all information in this document does not constitute any kind of warranty. Visit our website for the most up to date product information

For more information
For more information about Fiberroad Industrial Ethernet series products, Visit https://www.fiberroad.com or contact your local account representative.

© 2022 Fiberroad Technology Co Ltd All right reserved

References

• Industrial Ethernet & Optical Transport Network | Fiberroad
• Industrial Ethernet & Optical Transport Network | Fiberroad

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>